Philips AZ1027/96 User manual

Register your product and get support at AZ1027
EN User manual

© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
AZ1027_96_UM_V1.1

EN
1 Important
Safety
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
h Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
i Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
j Only use attachments/accessories specified by the
manufacturer.
k Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
l Unplug this apparatus during lightning storms or when unused
for long periods of time.
m Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
n Battery usage CAUTION – To prevent battery leakage which
may result in bodily injury, property damage, or damage to
the unit:
Install all batteries correctly, + and - as marked on the unit.
•
Do not mix batteries (old and new or carbon and alkaline, etc.).
•
Remove batteries when the unit is not used for a long time.
•
o Apparatus shall not be exposed to dripping or splashing.
p Do not place any sources of danger on the apparatus (e.g.
liquid filled objects, lighted candles).
q This product may contain lead and mercury. Disposal of
these materials may be regulated due to environmental
considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries
Alliance: www.eiae.org.

EN
1 Important
Safety
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
h Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
i Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
j Only use attachments/accessories specified by the
manufacturer.
k Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
l Unplug this apparatus during lightning storms or when unused
for long periods of time.
m Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
n Battery usage CAUTION – To prevent battery leakage which
may result in bodily injury, property damage, or damage to
the unit:
Install all batteries correctly, + and - as marked on the unit.
•
Do not mix batteries (old and new or carbon and alkaline, etc.).
•
Remove batteries when the unit is not used for a long time.
•
o Apparatus shall not be exposed to dripping or splashing.
p Do not place any sources of danger on the apparatus (e.g.
liquid filled objects, lighted candles).
q This product may contain lead and mercury. Disposal of
these materials may be regulated due to environmental
considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries
Alliance: www.eiae.org.

Warning
Never look into the laser beam inside the product. •
Never lubricate any part of this product. •
Never place this CD Soundmachine on other electrical equipment. •
Keep this product away from direct sunlight, naked flames or heat. •
Never look into the laser beam inside the product. •
Ensure that you always have easy access to the power cord, plug or •
adaptor to disconnect the CD Soundmachine from the power.
Notice
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Electronics may void the
user’s authority to operate the equipment.
This product complies with the radio interference requirements of
the European Community.
This product complies with the requirements of the following
directives and guidelines: 2004/108/EC + 2006/95/EC
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and constitute a criminal
offence. This equipment should not be used for such purposes.
Recording and playback of material might require consent. See
Copyright Act 1956 and The Performer’s Protection Acts 1958 to
1972.
Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
When you see the crossed-out wheel bin symbol with the chemical
symbol ‘Pb’, it means that the batteries comply with the requirement
set by the directive for lead:
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
This CD Soundmachine includes this label:
2 Your CD Soundmachine
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the CD Soundmachine you can play audio discs and listen to FM/
MW radio. You can also program the play sequence of tracks. Dynamic
Bass Boost (DBB) helps you to maximizes music enjoyment.
What’s in the box
Check and identify the contents of the package:
CD Soundmachine•
AC power cord•
User Manual•
Overview of the CD Soundmachine
MP3 LINK
c
a
b
h
dk
j
i
e
f
g
MP3 LINK
l
m
p
n
o
a VOLUME
Adjust volume level•
b DBB
Turn the bass enhancement on/off•
c Cassette recorder buttons

Warning
Never look into the laser beam inside the product. •
Never lubricate any part of this product. •
Never place this CD Soundmachine on other electrical equipment. •
Keep this product away from direct sunlight, naked flames or heat. •
Never look into the laser beam inside the product. •
Ensure that you always have easy access to the power cord, plug or •
adaptor to disconnect the CD Soundmachine from the power.
Notice
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Electronics may void the
user’s authority to operate the equipment.
This product complies with the radio interference requirements of
the European Community.
This product complies with the requirements of the following
directives and guidelines: 2004/108/EC + 2006/95/EC
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and constitute a criminal
offence. This equipment should not be used for such purposes.
Recording and playback of material might require consent. See
Copyright Act 1956 and The Performer’s Protection Acts 1958 to
1972.
Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
When you see the crossed-out wheel bin symbol with the chemical
symbol ‘Pb’, it means that the batteries comply with the requirement
set by the directive for lead:
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
This CD Soundmachine includes this label:
2 Your CD Soundmachine
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the CD Soundmachine you can play audio discs and listen to FM/
MW radio. You can also program the play sequence of tracks. Dynamic
Bass Boost (DBB) helps you to maximizes music enjoyment.
What’s in the box
Check and identify the contents of the package:
CD Soundmachine•
AC power cord•
User Manual•
Overview of the CD Soundmachine
MP3 LINK
c
a
b
h
dk
j
i
e
f
g
MP3 LINK
l
m
p
n
o
a VOLUME
Adjust volume level•
b DBB
Turn the bass enhancement on/off•
c Cassette recorder buttons

Warning
Never look into the laser beam inside the product. •
Never lubricate any part of this product. •
Never place this CD Soundmachine on other electrical equipment. •
Keep this product away from direct sunlight, naked flames or heat. •
Never look into the laser beam inside the product. •
Ensure that you always have easy access to the power cord, plug or •
adaptor to disconnect the CD Soundmachine from the power.
Notice
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Electronics may void the
user’s authority to operate the equipment.
This product complies with the radio interference requirements of
the European Community.
This product complies with the requirements of the following
directives and guidelines: 2004/108/EC + 2006/95/EC
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and constitute a criminal
offence. This equipment should not be used for such purposes.
Recording and playback of material might require consent. See
Copyright Act 1956 and The Performer’s Protection Acts 1958 to
1972.
Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
When you see the crossed-out wheel bin symbol with the chemical
symbol ‘Pb’, it means that the batteries comply with the requirement
set by the directive for lead:
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
This CD Soundmachine includes this label:
2 Your CD Soundmachine
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the CD Soundmachine you can play audio discs and listen to FM/
MW radio. You can also program the play sequence of tracks. Dynamic
Bass Boost (DBB) helps you to maximizes music enjoyment.
What’s in the box
Check and identify the contents of the package:
CD Soundmachine•
AC power cord•
User Manual•
Overview of the CD Soundmachine
MP3 LINK
c
a
b
h
dk
j
i
e
f
g
MP3 LINK
l
m
p
n
o
a VOLUME
Adjust volume level•
b DBB
Turn the bass enhancement on/off•
c Cassette recorder buttons

Warning
Never look into the laser beam inside the product. •
Never lubricate any part of this product. •
Never place this CD Soundmachine on other electrical equipment. •
Keep this product away from direct sunlight, naked flames or heat. •
Never look into the laser beam inside the product. •
Ensure that you always have easy access to the power cord, plug or •
adaptor to disconnect the CD Soundmachine from the power.
Notice
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Electronics may void the
user’s authority to operate the equipment.
This product complies with the radio interference requirements of
the European Community.
This product complies with the requirements of the following
directives and guidelines: 2004/108/EC + 2006/95/EC
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and constitute a criminal
offence. This equipment should not be used for such purposes.
Recording and playback of material might require consent. See
Copyright Act 1956 and The Performer’s Protection Acts 1958 to
1972.
Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
When you see the crossed-out wheel bin symbol with the chemical
symbol ‘Pb’, it means that the batteries comply with the requirement
set by the directive for lead:
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
This CD Soundmachine includes this label:
2 Your CD Soundmachine
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the CD Soundmachine you can play audio discs and listen to FM/
MW radio. You can also program the play sequence of tracks. Dynamic
Bass Boost (DBB) helps you to maximizes music enjoyment.
What’s in the box
Check and identify the contents of the package:
CD Soundmachine•
AC power cord•
User Manual•
Overview of the CD Soundmachine
MP3 LINK
c
a
b
h
dk
j
i
e
f
g
MP3 LINK
l
m
p
n
o
a VOLUME
Adjust volume level•
b DBB
Turn the bass enhancement on/off•
c Cassette recorder buttons

Warning
Never look into the laser beam inside the product. •
Never lubricate any part of this product. •
Never place this CD Soundmachine on other electrical equipment. •
Keep this product away from direct sunlight, naked flames or heat. •
Never look into the laser beam inside the product. •
Ensure that you always have easy access to the power cord, plug or •
adaptor to disconnect the CD Soundmachine from the power.
Notice
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Electronics may void the
user’s authority to operate the equipment.
This product complies with the radio interference requirements of
the European Community.
This product complies with the requirements of the following
directives and guidelines: 2004/108/EC + 2006/95/EC
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and constitute a criminal
offence. This equipment should not be used for such purposes.
Recording and playback of material might require consent. See
Copyright Act 1956 and The Performer’s Protection Acts 1958 to
1972.
Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
When you see the crossed-out wheel bin symbol with the chemical
symbol ‘Pb’, it means that the batteries comply with the requirement
set by the directive for lead:
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
This CD Soundmachine includes this label:
2 Your CD Soundmachine
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the CD Soundmachine you can play audio discs and listen to FM/
MW radio. You can also program the play sequence of tracks. Dynamic
Bass Boost (DBB) helps you to maximizes music enjoyment.
What’s in the box
Check and identify the contents of the package:
CD Soundmachine•
AC power cord•
User Manual•
Overview of the CD Soundmachine
MP3 LINK
c
a
b
h
dk
j
i
e
f
g
MP3 LINK
l
m
p
n
o
a VOLUME
Adjust volume level•
b DBB
Turn the bass enhancement on/off•
c Cassette recorder buttons

Pause play or record•
Stop cassette play or record•
Open the cassette holder•
/
Fast forward/rewind cassette•
Start cassette play•
Start cassette record•
d Display
e CD Buttons
Stop CD play•
Erase a CD program•
Start or pause CD play•
/
Select the previous/next track•
Fast search backward/forward within the current track•
f PROG
Program tracks and browse the program•
g LIFT TO OPEN
Open/Close the CD compartment•
h MODE
Select a play mode: REPEAT or SHUFFLE•
i BAND
Select a wave band•
j MP3 LINK
Socket for audio input•
k TUNING +/-
Tune to radio stations•
l Telescopic antenna
Improve FM reception•
m AC MAINS~
Socket for the power cord•
n Battery door
o Voltage Selector
p Source selector: CD, TUNER, MP3 LINK, TAPE/OFF
Select sound source•
Switch to standby mode•
3 Get started
Caution
Use of controls or adjustments or performance of procedures other •
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the
bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
1 Open the battery compartment.
2 Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct polarity
(+/-) as indicated.
3 Close the battery compartment.
Tip
If you want to save battery life, use the supplied power cord. •
Connect AC power
Warning
Risk of product damage! Ensure that the power supply voltage •
corresponds to the voltage printed on the back or the underside of
the CD Soundmachine.
Risk of electric shock! When you unplug the AC adaptor, always pull
•
the plug from the socket. Never pull the cord.
Note
Install the unit near the power supply socket and where the AC •
power plug can be easily reached.
1 Connect the power cord to the AC MAINS~ socket on the CD
Soundmachine and to the power supply socket.
To switch the CD Soundmachine off completely, disconnect the
•
power cord from the power supply socket.
Tip
To save energy: After use, set the source selector to • TAPE/OFF.
4 Use your CD Soundmachine
Play a CD
Note
You cannot play CDs encoded with copyright protection •
technologies.
You can play commercially available audio:
CDs•
6 x 1.5V R-14/UM-2/C-cell

Pause play or record•
Stop cassette play or record•
Open the cassette holder•
/
Fast forward/rewind cassette•
Start cassette play•
Start cassette record•
d Display
e CD Buttons
Stop CD play•
Erase a CD program•
Start or pause CD play•
/
Select the previous/next track•
Fast search backward/forward within the current track•
f PROG
Program tracks and browse the program•
g LIFT TO OPEN
Open/Close the CD compartment•
h MODE
Select a play mode: REPEAT or SHUFFLE•
i BAND
Select a wave band•
j MP3 LINK
Socket for audio input•
k TUNING +/-
Tune to radio stations•
l Telescopic antenna
Improve FM reception•
m AC MAINS~
Socket for the power cord•
n Battery door
o Voltage Selector
p Source selector: CD, TUNER, MP3 LINK, TAPE/OFF
Select sound source•
Switch to standby mode•
3 Get started
Caution
Use of controls or adjustments or performance of procedures other •
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the
bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
1 Open the battery compartment.
2 Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct polarity
(+/-) as indicated.
3 Close the battery compartment.
Tip
If you want to save battery life, use the supplied power cord. •
Connect AC power
Warning
Risk of product damage! Ensure that the power supply voltage •
corresponds to the voltage printed on the back or the underside of
the CD Soundmachine.
Risk of electric shock! When you unplug the AC adaptor, always pull
•
the plug from the socket. Never pull the cord.
Note
Install the unit near the power supply socket and where the AC •
power plug can be easily reached.
1 Connect the power cord to the AC MAINS~ socket on the CD
Soundmachine and to the power supply socket.
To switch the CD Soundmachine off completely, disconnect the
•
power cord from the power supply socket.
Tip
To save energy: After use, set the source selector to • TAPE/OFF.
4 Use your CD Soundmachine
Play a CD
Note
You cannot play CDs encoded with copyright protection •
technologies.
You can play commercially available audio:
CDs•
6 x 1.5V R-14/UM-2/C-cell

Pause play or record•
Stop cassette play or record•
Open the cassette holder•
/
Fast forward/rewind cassette•
Start cassette play•
Start cassette record•
d Display
e CD Buttons
Stop CD play•
Erase a CD program•
Start or pause CD play•
/
Select the previous/next track•
Fast search backward/forward within the current track•
f PROG
Program tracks and browse the program•
g LIFT TO OPEN
Open/Close the CD compartment•
h MODE
Select a play mode: REPEAT or SHUFFLE•
i BAND
Select a wave band•
j MP3 LINK
Socket for audio input•
k TUNING +/-
Tune to radio stations•
l Telescopic antenna
Improve FM reception•
m AC MAINS~
Socket for the power cord•
n Battery door
o Voltage Selector
p Source selector: CD, TUNER, MP3 LINK, TAPE/OFF
Select sound source•
Switch to standby mode•
3 Get started
Caution
Use of controls or adjustments or performance of procedures other •
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the
bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
1 Open the battery compartment.
2 Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct polarity
(+/-) as indicated.
3 Close the battery compartment.
Tip
If you want to save battery life, use the supplied power cord. •
Connect AC power
Warning
Risk of product damage! Ensure that the power supply voltage •
corresponds to the voltage printed on the back or the underside of
the CD Soundmachine.
Risk of electric shock! When you unplug the AC adaptor, always pull
•
the plug from the socket. Never pull the cord.
Note
Install the unit near the power supply socket and where the AC •
power plug can be easily reached.
1 Connect the power cord to the AC MAINS~ socket on the CD
Soundmachine and to the power supply socket.
To switch the CD Soundmachine off completely, disconnect the
•
power cord from the power supply socket.
Tip
To save energy: After use, set the source selector to • TAPE/OFF.
4 Use your CD Soundmachine
Play a CD
Note
You cannot play CDs encoded with copyright protection •
technologies.
You can play commercially available audio:
CDs•
6 x 1.5V R-14/UM-2/C-cell

Pause play or record•
Stop cassette play or record•
Open the cassette holder•
/
Fast forward/rewind cassette•
Start cassette play•
Start cassette record•
d Display
e CD Buttons
Stop CD play•
Erase a CD program•
Start or pause CD play•
/
Select the previous/next track•
Fast search backward/forward within the current track•
f PROG
Program tracks and browse the program•
g LIFT TO OPEN
Open/Close the CD compartment•
h MODE
Select a play mode: REPEAT or SHUFFLE•
i BAND
Select a wave band•
j MP3 LINK
Socket for audio input•
k TUNING +/-
Tune to radio stations•
l Telescopic antenna
Improve FM reception•
m AC MAINS~
Socket for the power cord•
n Battery door
o Voltage Selector
p Source selector: CD, TUNER, MP3 LINK, TAPE/OFF
Select sound source•
Switch to standby mode•
3 Get started
Caution
Use of controls or adjustments or performance of procedures other •
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the
bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
1 Open the battery compartment.
2 Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct polarity
(+/-) as indicated.
3 Close the battery compartment.
Tip
If you want to save battery life, use the supplied power cord. •
Connect AC power
Warning
Risk of product damage! Ensure that the power supply voltage •
corresponds to the voltage printed on the back or the underside of
the CD Soundmachine.
Risk of electric shock! When you unplug the AC adaptor, always pull
•
the plug from the socket. Never pull the cord.
Note
Install the unit near the power supply socket and where the AC •
power plug can be easily reached.
1 Connect the power cord to the AC MAINS~ socket on the CD
Soundmachine and to the power supply socket.
To switch the CD Soundmachine off completely, disconnect the
•
power cord from the power supply socket.
Tip
To save energy: After use, set the source selector to • TAPE/OFF.
4 Use your CD Soundmachine
Play a CD
Note
You cannot play CDs encoded with copyright protection •
technologies.
You can play commercially available audio:
CDs•
6 x 1.5V R-14/UM-2/C-cell

Pause play or record•
Stop cassette play or record•
Open the cassette holder•
/
Fast forward/rewind cassette•
Start cassette play•
Start cassette record•
d Display
e CD Buttons
Stop CD play•
Erase a CD program•
Start or pause CD play•
/
Select the previous/next track•
Fast search backward/forward within the current track•
f PROG
Program tracks and browse the program•
g LIFT TO OPEN
Open/Close the CD compartment•
h MODE
Select a play mode: REPEAT or SHUFFLE•
i BAND
Select a wave band•
j MP3 LINK
Socket for audio input•
k TUNING +/-
Tune to radio stations•
l Telescopic antenna
Improve FM reception•
m AC MAINS~
Socket for the power cord•
n Battery door
o Voltage Selector
p Source selector: CD, TUNER, MP3 LINK, TAPE/OFF
Select sound source•
Switch to standby mode•
3 Get started
Caution
Use of controls or adjustments or performance of procedures other •
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the
bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
1 Open the battery compartment.
2 Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct polarity
(+/-) as indicated.
3 Close the battery compartment.
Tip
If you want to save battery life, use the supplied power cord. •
Connect AC power
Warning
Risk of product damage! Ensure that the power supply voltage •
corresponds to the voltage printed on the back or the underside of
the CD Soundmachine.
Risk of electric shock! When you unplug the AC adaptor, always pull
•
the plug from the socket. Never pull the cord.
Note
Install the unit near the power supply socket and where the AC •
power plug can be easily reached.
1 Connect the power cord to the AC MAINS~ socket on the CD
Soundmachine and to the power supply socket.
To switch the CD Soundmachine off completely, disconnect the
•
power cord from the power supply socket.
Tip
To save energy: After use, set the source selector to • TAPE/OFF.
4 Use your CD Soundmachine
Play a CD
Note
You cannot play CDs encoded with copyright protection •
technologies.
You can play commercially available audio:
CDs•
6 x 1.5V R-14/UM-2/C-cell
CD-Recordables (CD-R)•
CD-Rewritables (CD-RW)•
1 Switch the source selector to CD.
2 Lift the lid of the CD compartment.
3 Insert a CD with the printed side facing up.
4 Close the CD lid gently.
The total number of tracks is displayed. »
5 Press to start play.
[ » ] is displayed.
To pause CD play, press • .
To resume CD play, press • again.
To stop CD play, press • .
Select a track
1 During play, press / to select a track.
Find a passage within a track
1 During play, press and hold /.
The CD is played at high speed and with reduced volume. »
2 Release / to resume normal play.
Tip
When search reaches the end of the last track, the CD stops. •
Program play sequence
You can store up to 20 tracks in the desired sequence.
1 In stop mode, press PROG to start to program play sequence.
[PROG] and [00] are displayed. »
2 Press / to select a track.
3 Press PROG to store the track.
4 Repeat steps 2 to 3 to select and store all tracks.
When all 20 tracks are stored, no more tracks can be selected »
and the display shows [---].
5 To play program, press .
In stop mode, press
• PROG repeatedly to browse stored tracks.
To cancel program, press
• twice.
Tip
When program play stops, the CD Soundmachine returns to normal •
play. To play program again, repeat steps 1 to 5.
Select play modes
Repeat play
You can repeat a track, a disc, or a program.
[• ] – plays the current track continuously
[• ALL] – repeats the entire CD/program
1 During play, press MODE repeatedly until the display shows the
repeat icon.
Repeat one track.
•
Repeat the entire CD.
•
To stop repeat play, press • MODE repeatedly until the repeat
icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1 During play, press MODE repeatedly until the display shows the
shuffle icon.
To stop shuffle play, press • MODE again.
Listen to radio
1 Switch the source selector to TUNER.
2 Switch BAND to FM or MW.
3 Turn TUNING +/- to find a station.
Tip
To improve FM reception, you can extend, incline or turn the •
telescopic antenna for best reception.
To improve MW reception, turn the CD Soundmachine to face a
•
different direction.
Play cassette recorder
1 Switch the source selector to TAPE/OFF.
2 Press to open the cassette holder, insert a cassette tape,
and then close the cassette holder.
3 Press to start play.
To pause play, press • .
To stop the play, press • .
Find a passage within a tape
1 During stop, press / to search for a desired passage in a
tape.
2 To stop fast search, press .
PROG
ALL
T
f

CD-Recordables (CD-R)•
CD-Rewritables (CD-RW)•
1 Switch the source selector to CD.
2 Lift the lid of the CD compartment.
3 Insert a CD with the printed side facing up.
4 Close the CD lid gently.
The total number of tracks is displayed. »
5 Press to start play.
[ » ] is displayed.
To pause CD play, press • .
To resume CD play, press • again.
To stop CD play, press • .
Select a track
1 During play, press / to select a track.
Find a passage within a track
1 During play, press and hold /.
The CD is played at high speed and with reduced volume. »
2 Release / to resume normal play.
Tip
When search reaches the end of the last track, the CD stops. •
Program play sequence
You can store up to 20 tracks in the desired sequence.
1 In stop mode, press PROG to start to program play sequence.
[PROG] and [00] are displayed. »
2 Press / to select a track.
3 Press PROG to store the track.
4 Repeat steps 2 to 3 to select and store all tracks.
When all 20 tracks are stored, no more tracks can be selected »
and the display shows [---].
5 To play program, press .
In stop mode, press
• PROG repeatedly to browse stored tracks.
To cancel program, press
• twice.
Tip
When program play stops, the CD Soundmachine returns to normal •
play. To play program again, repeat steps 1 to 5.
Select play modes
Repeat play
You can repeat a track, a disc, or a program.
[• ] – plays the current track continuously
[• ALL] – repeats the entire CD/program
1 During play, press MODE repeatedly until the display shows the
repeat icon.
Repeat one track.
•
Repeat the entire CD.
•
To stop repeat play, press • MODE repeatedly until the repeat
icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1 During play, press MODE repeatedly until the display shows the
shuffle icon.
To stop shuffle play, press • MODE again.
Listen to radio
1 Switch the source selector to TUNER.
2 Switch BAND to FM or MW.
3 Turn TUNING +/- to find a station.
Tip
To improve FM reception, you can extend, incline or turn the •
telescopic antenna for best reception.
To improve MW reception, turn the CD Soundmachine to face a
•
different direction.
Play cassette recorder
1 Switch the source selector to TAPE/OFF.
2 Press to open the cassette holder, insert a cassette tape,
and then close the cassette holder.
3 Press to start play.
To pause play, press • .
To stop the play, press • .
Find a passage within a tape
1 During stop, press / to search for a desired passage in a
tape.
2 To stop fast search, press .
PROG
ALL
T
f

CD-Recordables (CD-R)•
CD-Rewritables (CD-RW)•
1 Switch the source selector to CD.
2 Lift the lid of the CD compartment.
3 Insert a CD with the printed side facing up.
4 Close the CD lid gently.
The total number of tracks is displayed. »
5 Press to start play.
[ » ] is displayed.
To pause CD play, press • .
To resume CD play, press • again.
To stop CD play, press • .
Select a track
1 During play, press / to select a track.
Find a passage within a track
1 During play, press and hold /.
The CD is played at high speed and with reduced volume. »
2 Release / to resume normal play.
Tip
When search reaches the end of the last track, the CD stops. •
Program play sequence
You can store up to 20 tracks in the desired sequence.
1 In stop mode, press PROG to start to program play sequence.
[PROG] and [00] are displayed. »
2 Press / to select a track.
3 Press PROG to store the track.
4 Repeat steps 2 to 3 to select and store all tracks.
When all 20 tracks are stored, no more tracks can be selected »
and the display shows [---].
5 To play program, press .
In stop mode, press
• PROG repeatedly to browse stored tracks.
To cancel program, press
• twice.
Tip
When program play stops, the CD Soundmachine returns to normal •
play. To play program again, repeat steps 1 to 5.
Select play modes
Repeat play
You can repeat a track, a disc, or a program.
[• ] – plays the current track continuously
[• ALL] – repeats the entire CD/program
1 During play, press MODE repeatedly until the display shows the
repeat icon.
Repeat one track.
•
Repeat the entire CD.
•
To stop repeat play, press • MODE repeatedly until the repeat
icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1 During play, press MODE repeatedly until the display shows the
shuffle icon.
To stop shuffle play, press • MODE again.
Listen to radio
1 Switch the source selector to TUNER.
2 Switch BAND to FM or MW.
3 Turn TUNING +/- to find a station.
Tip
To improve FM reception, you can extend, incline or turn the •
telescopic antenna for best reception.
To improve MW reception, turn the CD Soundmachine to face a
•
different direction.
Play cassette recorder
1 Switch the source selector to TAPE/OFF.
2 Press to open the cassette holder, insert a cassette tape,
and then close the cassette holder.
3 Press to start play.
To pause play, press • .
To stop the play, press • .
Find a passage within a tape
1 During stop, press / to search for a desired passage in a
tape.
2 To stop fast search, press .
PROG
ALL
T
f

CD-Recordables (CD-R)•
CD-Rewritables (CD-RW)•
1 Switch the source selector to CD.
2 Lift the lid of the CD compartment.
3 Insert a CD with the printed side facing up.
4 Close the CD lid gently.
The total number of tracks is displayed. »
5 Press to start play.
[ » ] is displayed.
To pause CD play, press • .
To resume CD play, press • again.
To stop CD play, press • .
Select a track
1 During play, press / to select a track.
Find a passage within a track
1 During play, press and hold /.
The CD is played at high speed and with reduced volume. »
2 Release / to resume normal play.
Tip
When search reaches the end of the last track, the CD stops. •
Program play sequence
You can store up to 20 tracks in the desired sequence.
1 In stop mode, press PROG to start to program play sequence.
[PROG] and [00] are displayed. »
2 Press / to select a track.
3 Press PROG to store the track.
4 Repeat steps 2 to 3 to select and store all tracks.
When all 20 tracks are stored, no more tracks can be selected »
and the display shows [---].
5 To play program, press .
In stop mode, press
• PROG repeatedly to browse stored tracks.
To cancel program, press
• twice.
Tip
When program play stops, the CD Soundmachine returns to normal •
play. To play program again, repeat steps 1 to 5.
Select play modes
Repeat play
You can repeat a track, a disc, or a program.
[• ] – plays the current track continuously
[• ALL] – repeats the entire CD/program
1 During play, press MODE repeatedly until the display shows the
repeat icon.
Repeat one track.
•
Repeat the entire CD.
•
To stop repeat play, press • MODE repeatedly until the repeat
icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1 During play, press MODE repeatedly until the display shows the
shuffle icon.
To stop shuffle play, press • MODE again.
Listen to radio
1 Switch the source selector to TUNER.
2 Switch BAND to FM or MW.
3 Turn TUNING +/- to find a station.
Tip
To improve FM reception, you can extend, incline or turn the •
telescopic antenna for best reception.
To improve MW reception, turn the CD Soundmachine to face a
•
different direction.
Play cassette recorder
1 Switch the source selector to TAPE/OFF.
2 Press to open the cassette holder, insert a cassette tape,
and then close the cassette holder.
3 Press to start play.
To pause play, press • .
To stop the play, press • .
Find a passage within a tape
1 During stop, press / to search for a desired passage in a
tape.
2 To stop fast search, press .
PROG
ALL
T
f

CD-Recordables (CD-R)•
CD-Rewritables (CD-RW)•
1 Switch the source selector to CD.
2 Lift the lid of the CD compartment.
3 Insert a CD with the printed side facing up.
4 Close the CD lid gently.
The total number of tracks is displayed. »
5 Press to start play.
[ » ] is displayed.
To pause CD play, press • .
To resume CD play, press • again.
To stop CD play, press • .
Select a track
1 During play, press / to select a track.
Find a passage within a track
1 During play, press and hold /.
The CD is played at high speed and with reduced volume. »
2 Release / to resume normal play.
Tip
When search reaches the end of the last track, the CD stops. •
Program play sequence
You can store up to 20 tracks in the desired sequence.
1 In stop mode, press PROG to start to program play sequence.
[PROG] and [00] are displayed. »
2 Press / to select a track.
3 Press PROG to store the track.
4 Repeat steps 2 to 3 to select and store all tracks.
When all 20 tracks are stored, no more tracks can be selected »
and the display shows [---].
5 To play program, press .
In stop mode, press
• PROG repeatedly to browse stored tracks.
To cancel program, press
• twice.
Tip
When program play stops, the CD Soundmachine returns to normal •
play. To play program again, repeat steps 1 to 5.
Select play modes
Repeat play
You can repeat a track, a disc, or a program.
[• ] – plays the current track continuously
[• ALL] – repeats the entire CD/program
1 During play, press MODE repeatedly until the display shows the
repeat icon.
Repeat one track.
•
Repeat the entire CD.
•
To stop repeat play, press • MODE repeatedly until the repeat
icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1 During play, press MODE repeatedly until the display shows the
shuffle icon.
To stop shuffle play, press • MODE again.
Listen to radio
1 Switch the source selector to TUNER.
2 Switch BAND to FM or MW.
3 Turn TUNING +/- to find a station.
Tip
To improve FM reception, you can extend, incline or turn the •
telescopic antenna for best reception.
To improve MW reception, turn the CD Soundmachine to face a
•
different direction.
Play cassette recorder
1 Switch the source selector to TAPE/OFF.
2 Press to open the cassette holder, insert a cassette tape,
and then close the cassette holder.
3 Press to start play.
To pause play, press • .
To stop the play, press • .
Find a passage within a tape
1 During stop, press / to search for a desired passage in a
tape.
2 To stop fast search, press .
PROG
ALL
T
f

d
s.
e
e
Record from CD
1 Switch the source selector to CD.
2 Insert a CD with the printed side facing up.
3 If you want to record tracks in the desired sequence, program
the desired tracks.
4 Press to open the cassette holder.
5 Insert a blank cassette.
6 Close the holder.
7 Press to start to record.
The disc/program starts automatically from the beginning. »
To pause, press • .
To resume, press • again.
To stop, press • .
Record from radio
1 Switch the source selector to TUNER.
2 Tune to a radio station.
3 Press to open the cassette holder.
4 Insert a blank cassette.
5 Close the holder.
6 Press to start to record.
To pause, press • .
To resume, press • again.
To stop, press • .
5 Troubleshooting
Warning
Never remove the casing of this apparatus. •
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the
following points before requesting service. If the problem remains
unsolved, go to the Philips web site (www.Philips.com/support), or
contact Philips (see Contact information). When you contact Philips,
ensure that the apparatus is nearby and the model number and serial
number are available.
No power
Ensure that the power cord is connected securely. •
Ensure that there is power at the power supply socket. •
Ensure that the batteries are installed correctly. •
No sound
Adjust the volume. •
Ensure that the track played is of a compatible format. •
Display does not function properly./No reaction to operation of any
of the controls.
1 Disconnect the AC power cord.
2 Connect the AC power cord after a few seconds.
Cannot play disc
Ensure that the disc label is inserted with the printed side facing •
up.
Wipe the disc with fibre cleaning cloth from the centre to the •
edge in a straight line.
This disc may be defective. Play another disc. •
Ensure that the CD is a finalised CD/CD-R/CD-RW. •
Ensure that the laser lens is clean. •
Ensure that the CD is not encoded with copyright protection •
technologies.
The CD skips tracks
Ensure that the CD is not damaged or dirty. •
Ensure that program/shuffle mode is deactivated. •
Poor cassette sound quality
Ensure that heads in the cassette holder are clean.•
Ensure that a NORMAL (IECI) cassette tape is used for record.•
Cassette does not work for record
Ensure that cassette tabs are not broken.•
6 Product information
Note
Product information is subject to change without prior notice. •
Dimensions (Main unit)
(W x H x D)
291 x 146 x 243 mm
11.5 x 5.8 x 9.6 inches
Weight (Main unit) 1.8 kg
3.8 pound
Power supply DC 9V 1.5 A
AC 110V~127V, 220~240 V
Power consumption Active 12W
Standby < 2W
Power output 2 x 1W RMS
Operating temperature range -10°C - +50°C
14°F - 122°F

d
s.
e
e
Record from CD
1 Switch the source selector to CD.
2 Insert a CD with the printed side facing up.
3 If you want to record tracks in the desired sequence, program
the desired tracks.
4 Press to open the cassette holder.
5 Insert a blank cassette.
6 Close the holder.
7 Press to start to record.
The disc/program starts automatically from the beginning. »
To pause, press • .
To resume, press • again.
To stop, press • .
Record from radio
1 Switch the source selector to TUNER.
2 Tune to a radio station.
3 Press to open the cassette holder.
4 Insert a blank cassette.
5 Close the holder.
6 Press to start to record.
To pause, press • .
To resume, press • again.
To stop, press • .
5 Troubleshooting
Warning
Never remove the casing of this apparatus. •
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the
following points before requesting service. If the problem remains
unsolved, go to the Philips web site (www.Philips.com/support), or
contact Philips (see Contact information). When you contact Philips,
ensure that the apparatus is nearby and the model number and serial
number are available.
No power
Ensure that the power cord is connected securely. •
Ensure that there is power at the power supply socket. •
Ensure that the batteries are installed correctly. •
No sound
Adjust the volume. •
Ensure that the track played is of a compatible format. •
Display does not function properly./No reaction to operation of any
of the controls.
1 Disconnect the AC power cord.
2 Connect the AC power cord after a few seconds.
Cannot play disc
Ensure that the disc label is inserted with the printed side facing •
up.
Wipe the disc with fibre cleaning cloth from the centre to the •
edge in a straight line.
This disc may be defective. Play another disc. •
Ensure that the CD is a finalised CD/CD-R/CD-RW. •
Ensure that the laser lens is clean. •
Ensure that the CD is not encoded with copyright protection •
technologies.
The CD skips tracks
Ensure that the CD is not damaged or dirty. •
Ensure that program/shuffle mode is deactivated. •
Poor cassette sound quality
Ensure that heads in the cassette holder are clean.•
Ensure that a NORMAL (IECI) cassette tape is used for record.•
Cassette does not work for record
Ensure that cassette tabs are not broken.•
6 Product information
Note
Product information is subject to change without prior notice. •
Dimensions (Main unit)
(W x H x D)
291 x 146 x 243 mm
11.5 x 5.8 x 9.6 inches
Weight (Main unit) 1.8 kg
3.8 pound
Power supply DC 9V 1.5 A
AC 110V~127V, 220~240 V
Power consumption Active 12W
Standby < 2W
Power output 2 x 1W RMS
Operating temperature range -10°C - +50°C
14°F - 122°F