Philips HQ 4807 User manual

ENGLISH 4
POLSKI 11
ROMÂNĂ 18
РУССКИЙ 25
ČESKY 33
MAGYAR 39
SLOVENSKY 46
УКРАЇНСЬКІЙ 53
HRVATSKI 60
EESTI 66
LATVISKI 72
LIETUVIŠKAI 79
SLOVENŠČINA 85
HQ4807,4806,4800
3

Important
◗Make sure the appliance and the cord do not
get wet.
◗Only use the cord supplied.
Charge indications
C◗Charging
As soon as you start charging the empty shaver,
the green pilot light will go on.
A fully charged shaver has a cordless shaving time
of up to 30 minutes.
Charging
Recharge and keep the appliance at a
temperature between 5cC and 35cC.
The appliance is suitable for mains voltages
ranging from 100 to 240V.
You can also shave without charging by
connecting the shaver to the mains.
To extend the lifetime of the battery,remove the
powerplug from the wall socket and pull the
appliance plug out of the shaver when the battery
has been fully charged.
C1Put the appliance plug in the shaver.
2Put the powerplug in the wall socket.
Do not recharge the shaver in a closed pouch.
ENGLISH4

3When charging for the first time and after
a long period of disuse:leave the shaver to
charge for 24 hours.
Charging normally takes approx.16 hours.
4Remove the powerplug from the socket
and pull the appliance plug out of the
shaver when the battery has been fully
charged.
Shaving
1Switch the appliance on by sliding the
on/off button upwards.
C2Move the shaving heads quickly over your
skin,making both straight and circular
movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philishave system.
3Switch the shaver off.
C4Put the protection cap on the shaver to
prevent damage.
Replace the shaving heads (type HQ4 Micro
Action) every 2 years for optimal shaving results.
ENGLISH 5

Trimming
For grooming sideburns and moustache.
C1Open the trimmer by pushing the slide
upwards.
The trimmer can be activated while the motor is
running.
Cleaning
◗Regular cleaning guarantees better shaving
performance.
C◗For easy and optimal cleaning,the Philishave
Action Clean (shaving head cleaner,type
HQ100) is available.Ask your Philishave dealer
for information.
You can also clean the shaver in the following
way:
Shaving unit
Clean the shaving unit every week.
1Switch the shaver off,remove the
powerplug from the wall socket and pull
the appliance plug out of the shaver.
C2Clean the top of the appliance first,using
the brush supplied.
ENGLISH6

C3Remove the shaving unit.
C4Clean the inside of the shaving unit and the
hair chamber with the brush.
5Put the shaving unit back onto the shaver.
Shaving heads
Clean the shaving heads every two months.
1Switch the shaver off,remove the
powerplug from the wall socket and pull
the appliance plug out of the shaver.
C2Remove the shaving unit.
C3Turn the wheel anticlockwise and remove
the retaining frame.
C4Remove and clean the shaving heads
(cutters and guards) one by one.
Do not mix up the cutters and the guards.
This is essential since each cutter has been
ground with its corresponding guard for optimal
ENGLISH 7
2
1

performance. If you accidentally mix the sets up,it
could take several weeks before optimal shaving
performance is restored.
C5Clean the cutter with the short-bristled
side of the brush.
Brush carefully in the direction of the arrow.
C6Brush the guard.
If necessary,you can clean the shaving unit with a
degreasing liquid (e.g.alcohol). Remember to
lubricate the central point of the guards with a
drop of sewing machine oil after cleaning.
C7Reassemble the shaving unit by replacing
the retaining frame.Press the wheel and
turn it clockwise.
8Put the shaving unit back onto the shaver.
Trimmer
Clean the trimmer every time you have used it.
1Switch the shaver off,remove the
powerplug from the wall socket and pull
the appliance plug out of the shaver.
2Brush the trimmer.
3Lubricate the trimmer teeth with a drop
of sewing machine oil every six months.
ENGLISH8
2
1

Disposal of the battery
Remove the battery when you discard the
appliance.Do not throw the battery away with
the normal household waste,but hand it in at an
official collection point.You can also take the
battery to a Philips Service Centre, which will
dispose of it in an environmentally safe way.
Only remove the battery if it is completely empty.
1Remove the powerplug from the wall
socket and pull the appliance plug out of
the shaver.
C2Let the shaver run until it stops,undo the
screws and open the shaver.
3Remove the battery.
Do not connect the shaver to the mains again
after the battery has been removed.
Troubleshooting
◗Problem:The shaver does not work after the
on/off button has been slided upwards.
BSolution:Recharge the battery.
If the shaver still does not work,see 'Guarantee &
service'.
ENGLISH 9

Guarantee & service
If you need information or if you have a problem,
please visit the PhilipsWeb site at
www.philips.com or contact the Philips Customer
Care Centre in your country (you will find its
phone number in the worldwide guarantee
leaflet).If there is no Customer Care Centre in
your country,turn to your local Philips dealer or
contact the Service Department of Philips
Domestic Appliances and Personal Care BV.
ENGLISH10

Ważne
◗Upewnij się, że urządzenie i przewód nie są
wilgotne.
◗Używaj wyłącznie przewodu zasilającego, w
który zostało wyposażone urządzenie.
Wskaźniki ład wania
C◗Ładowanie
Gdy urządzenie zaczyna się ładować zapala się
zielona lampka kontrolna.
Całkowicie naładowana golarka pozwala na
30 minut golenia.
Ład wanie
Ładuj i przec owuj golarkę w temperaturze
pomiędzy 5ca 35cC.
Urządzenie jest dostosowane do napięcia
sieciowego od 100 do 240 V.
Możesz także używać golarki bez ładowania,
podłączając ją bezpośrednio do sieci.
Aby wydłużyć trwałość akumulatorów, wyjmij
wtyczkę z gniazdka ściennego i małą wtyczkę z
urządzenia, gdy akumulator będzie w pełni
naładowany.
C1Włóż ałą wtyczkę przewodu zasilającego
do golarki.
2Podłącz ładowarkę do sieci.
Nie ładuj golarki w zamkniętej saszetce.
POLSKI 11

3Podczas ładowania urządzenia po raz
pierwszy lub po dłuższy okresie
nieużywania: pozostaw golarkę podłączoną
do sieci przez 24 godziny.
Ładowanie zajmuje ok. 16 godzin.
4Gdy aku ulator jest całkowicie
naładowany wyj ij wtyczkę z gniazdka
sieciowego i odłącz urządzenie.
G lenie
1Włącz urządzenie, przesuwając włącznik
do góry.
C2Przesuwaj głowice po skórze, wykonując
zarówno proste, jak i okrężne ruchy.
Najlepsze efekty golenia osiąga się na skórze
suc ej.
Skóra Twojej twarzy potrzebuje pewnego czasu
(2-3 tygodni), by przyzwyczaić się do nowego
systemu golenia.
3Wyłącz urządzenie.
C4Załóż na golarkę nakładkę ochronną.
Aby uzyskać najlepsze efekty golenia, należy co
2 lata wymieniać głowice golące (typ HQ4 Micro
Action).
POLSKI12