Philips HQ6735/01 User manual

ENGLISH 4
FRANÇAIS 18
ESPAÑOL 32
PORTUGUÊS 47
73
87
HQ6735
3
á«Hô©dG

ENGLISH4
Introduction
The shaver comes with two different kinds of
NIVEA FOR MEN cartridges:Extra Fresh Shaving
Gel for a fresh sensation during and after shaving
and Moisturising Shaving Lotion for sensitive skin.
This gives you the opportunity to try them out
and discover which one suits your skin type best.
Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗Only use the HQ600 powerplug and the
charging stand supplied to charge the shaver.
◗Only the powerplug supplied guarantees
safety.
◗The HQ600 powerplug transforms 100-240
volts to a safe low voltage of less than
24 volts.
◗The powerplug contains a transformer.Do
not cut off the powerplug to replace it with
another plug,as this will cause a hazardous
situation.
C◗Never immerse the charging stand in water
nor rinse it under the tap when the charging
stand is plugged in.
C◗The shaver runs at a safe low voltage of less
than 24 volts.It is watertight and can be
cleaned under the tap.Rinse the shaver with
hot water.

Be careful with hot water.Always check if the
water isn't too hot,to prevent your hands from
burning.
◗Do not leave the charging stand with the
shaver in it plugged into the mains
continuously.
◗Check if the gel and lotion supplied with the
appliance contain ingredients (see back of
cartridge) to which you are allergic before
you start using the appliance.Do not use the
gel and/or lotion if you are allergic to one or
more ingredients!
◗If the mains cord of this appliance is damaged,
it must always be replaced by Philips or a
service centre authorised by Philips in order
to avoid hazardous situations.
Charging
Charge indications
C◗As soon as you start charging the empty
shaver,the green pilot light goes on.
◗The red pilot light blinks when the batteries
are almost empty.
◗When the batteries are almost empty,the red
pilot light blinks a few times after the shaver
has been switched off.
ENGLISH 5

ENGLISH6
Charging the appliance
Recharge,store and use the appliance at a
temperature between 5cC and 35cC.
1Insert the small plug into the charging
stand and put the powerplug in the wall
socket.
C2Place the shaver in the charging stand.
C3Press until you hear a click.
The shaver automatically switches off when
placed in the charging stand.
4When charging for the first time or after a
long period of disuse:leave the shaver to
charge continuously for 24 hours.
Charging normally takes approx.8 hour.
A fully charged shaver has a cordless shaving time
of up to approx.40 minutes.
Inserting the cartridge
Cartridges with moisturising NIVEA FOR MEN
shaving gel/lotion are available in boxes containing
five cartridges and one small plastic pump.
Do not throw the pump away when you replace
an empty cartridge.You will need it for all five
cartridges.

ENGLISH 7
One Philishave NIVEA FOR MEN Cool Skin
cartridge contains enough gel/lotion for approx.
10 shaves.
Remove the shaving gel/lotion cartridge from the
appliance when you are not going to use the
shaver for more than one week.
Use only Philishave NIVEA FOR MEN Cool Skin
(HQ160 or HQ161) cartridges.
For hygienic reasons,we advise you to insert a
new pump when you start using a new set of five
cartridges.
When you have run out of shaving gel/lotion
cartridges and you do not know where to buy
them,contact the Customer Care Centre in your
country (see 'Guarantee & service').
Inserting the cartridge
C1Take one cartridge from the box.Take the
pump (supplied in the same box) out of its
bag and push it into the cartridge until it
locks into position with a click.
C2Move the release slide downwards and
open the cover of the cartridge
compartment.
12

ENGLISH8
C3Slide the cartridge with the pump into the
shaver.It only fits properly if the white side
of the pump is pointing upwards.
4Close the cover (you will hear a click).
5Press the yellow pump button a few times
until the NIVEA FOR MEN shaving
emulsion appears.The shaver is now ready
for use.
BThe NIVEA FOR MEN shaving gel/lotion in the
cartridges will keep for 32 months when stored at
temperatures between 0cC and +40cC.
Using the appliance
Shaving
Switching on the shaver.
1Switch the shaver on by pressing the on/off
button once.
C2Press the yellow pump button to apply
NIVEA FOR MEN shaving gel/lotion to
your skin.
3Move the shaving heads over your skin,
making both straight and circular
movements.
4While shaving,press the pump button
frequently to apply more NIVEA FOR

MEN shaving gel/lotion so that the shaver
keeps gliding smoothly over your face.
Do not press the shaver too hard against your
skin while shaving.If you prefer,you can wet your
face before shaving.
◗When you have run out of shaving emulsion,
you can also use the shaver without it on a
dry face.
The shaver will not perform optimally when used
without shaving gel/lotion.
◗Your skin may need 2-3 weeks to get
accustomed to the Philishave system.
Switching of the shaver
1Switch the shaver off.
C2Put the protection cap on the shaver every
time you have used it,to prevent damage.
Remove the cartridge and clean the shaver if you
are not going to use the appliance for more than
one week.Rinse the shaver after each shave.
Trimming
The shaver has a separate trimmer for grooming
sideburns and moustache.
1Switch the shaver off.
Clean the shaver before you attach the trimmer.
ENGLISH 9

C2Press the release button to open the
shaving unit and pull the shaving unit off
the shaver.
C3Tilt the trimmer slightly backwards and fit
it onto the shaver.
4Remove the trimmer by pressing the
release button again and pulling the
trimmer off the shaver.
Cleaning and maintenance
Shaving unit
Rinse the shaving unit and the hair chamber with
hot water (60cC - 80cC) after every use.
1Switch the shaver off.
C2Press the release button to open the
shaving unit.
C3Clean the shaving unit and the hair
chamber by rinsing them under a hot tap
for some time.
Never dry the shaving unit with a towel or tissue
as this may damage the shaving heads.
ENGLISH10
2
1
2

C4Rinse the outside of the shaver.
Make sure the inside of the shaving unit and the
hair chamber have been cleaned properly.Close
the shaving unit and shake off excess water.
Charging stand
1Unplug the charging stand.
2Clean the charging stand with a moist
cloth.
Trimmer
1Clean the outside of the trimmer with the
brush supplied after every use.
C2Open the trimmer to clean it on the
inside.
C3Lubricate the trimmer teeth with a drop
of sewing machine oil every six months.
Replacement
Replace the shaving heads every two years for
optimal shaving results.
1Switch the shaver off.
ENGLISH 11
OIL

C2Press the release button to open the
shaving unit.
C3Turn the wheel anticlockwise and remove
the retaining frame.
C4Remove the shaving heads and place the
new ones in the shaving unit.
C5Put the retaining frame back onto the
shaving unit,press the wheel and turn it
clockwise.
Replace damaged or worn shaving heads with
Philishave HQ167 Cool Skin shaving heads only.
Storage
C◗After cleaning,the wet shaver can be placed in
the charging stand.
◗The appliance and the trimmer can be stored
in the pouch or cassette supplied.Whether
you have a pouch or a cassette depends on
your type of shaver.
ENGLISH12
1
1
2
1
1

Environment
Disposal of batteries
The built-in rechargeable batteries contain
substances that may pollute the environment.
Remove the batteries when you discard the
shaver.Do not throw the batteries away with the
normal household waste,but hand them in at an
official collection point.You can also take the
appliance to a Philips service centre,which will
remove them for you and will dispose of them in
an environmentally safe way.
Only remove the batteries if they are completely
empty.
C1Let the shaver run until it stops,undo the
screws and open the shaver.
2Remove the batteries.
Do not put the shaver back into the charging
stand after the batteries have been removed.
Accessories
The following accessories are available:
HQ167 Philishave Cool Skin shaving heads.
HQ160 NIVEA FOR MEN Cool Skin moisturising
shaving emulsion.
HQ161 NIVEA FOR MEN Cool Skin moisturising
fresh shaving gel.
ENGLISH 13

ENGLISH14
HQ8000 powerplug.
HQ100 PhilishaveAction Clean
(shaving head cleaner).
HQ101 PhilishaveAction Clean refill
(shaving head cleaning liquid).
HQ110 Philishave shaving head cleaner
(shaving head cleaning spray).
Guarantee & service
If you need information or if you have a problem,
please visit the PhilipsWeb site at
www.philips.com or contact the Philips Customer
Care Centre in your country (you will find its
phone number in the worldwide guarantee
leaflet).If there is no Customer Care Centre in
your country,turn to your local Philips dealer or
contact the Service Department of Philips
Domestic Appliances and Personal Care BV.
Troubleshooting
1The shaving heads do not move smoothly
over the skin:
BCause:not enough shaving emulsion has been
applied.
◗Press the pump button a few times until a
sufficient amount of NIVEA FOR MEN shaving
emulsion has been released to allow the
shaving heads to move smoothly over your
face again.

2Reduced shaving performance:
BCause 1:the shaving heads are dirty.The shaver
has not been cleaned immediately after use
and/or has not been rinsed long enough and/or
the water used to rinse the shaver was not hot
enough.
◗Clean the shaver thoroughly before you
continue shaving (see 'Cleaning').
BCause 2:long hairs are obstructing the shaving
heads.
C◗Remove the retaining frame.
C◗Clean the cutters and guards.
Do not clean more than one cutter and guard at
a time,since they are all matching sets.If you
accidentally mix up the cutters and guards,it
could take several weeks before optimal shaving
performance is restored.
◗Remove the hairs.
◗Put the shaving heads back into the shaving
unit.Put the retaining frame back onto the
shaving unit,press the wheel and turn it
clockwise.
BCause 3:the shaving heads are damaged or worn.
◗Remove the retaining frame.
◗Remove the old shaving heads from the
shaving unit and replace them with new ones.
ENGLISH 15
1
1
2

ENGLISH16
Damaged or worn shaving heads (cutters and
guards) must only be replaced with the original
Philishave HQ167 Cool Skin shaving heads.
◗Put the retaining frame back onto the shaving
unit,press the wheel and turn it clockwise.
3The shaver does not work when the on/off
button is pressed:
BCause:the batteries are empty
◗Recharge the batteries.
4The cover of the cartridge compartment
cannot be closed
BCause 1:the cartridge has not been inserted
correctly.
◗Insert the cartridge correctly.It only fits
properly into the shaver if the white side of
the pump is pointing upwards.
BCause 2:the cartridge has not been pushed far
enough into the shaver.
◗Press the cartridge until it is properly seated.
5The NIVEA FOR MEN shaving emulsion
has changed colour or has turned watery.
BCause:the NIVEA FOR MEN shaving emulsion
has not been stored at the right temperature.

ENGLISH 17
◗Insert a new cartridge.
6Skin irritation occurs:
BCause 1:your skin has not yet become
accustomed to this shaving system.
◗Allow 2-3 weeks for your skin to get
accustomed to this shaving system.
BCause 2:the shaving emulsion irritates your skin.
◗Try the other type of shaving emulsion.
◗Wet your face before shaving with the shaving
emulsion.
If the irritation does not disappear within 24
hours,we advise you to stop using the shaving
emulsion and to contact your doctor.
7In case of other problems:
◗See 'Guarantee & service'

Introduction
Votre rasoir est livré avec 2 types différents de
cartouches NIVEA FOR MEN:un Gel à Raser
Extra Rafraîchissant pour une sensation de
fraîcheur pendant et après le rasage et une Lotion
à Raser Hydratante pour peau sensible.Cela vous
offre l'opportunité d'essayer et de choisir laquelle
convient le mieux à votre type de peau.
Important
Avant d'utiliser l'appareil,lisez les instructions ci-
dessous et conservez ce mode d'emploi pour un
usage ultérieur.
◗Utilisez exclusivement le chargeur et le
support de charge fournis.
◗Le chargeur fourni garantit la sécurité.
◗Le chargeur transforme le 100-240V en 24V.
◗Le chargeur est doté d'un transformateur.
N'essayez pas de remplacer la fiche du
chargeur pour éviter tout accident.
C◗N'immergez jamais le support de charge dans
l'eau,ne le rincez pas non plus s'il est branché.
C◗Le rasoir fonctionne sous une tension de
sécurité de 24V.Il est étanche et peut être
nettoyé à l'eau courante.Rincez-le à l'eau
chaude.
Faites attention que l'eau ne soit pas trop chaude.
◗Ne laissez pas le support de charge avec le
rasoir branché continuellement.
FRANÇAIS18

◗Avant la première utilisation,vérifiez que le
gel ou la lotion fourni(e) avec l'appareil ne
contient pas des ingrédients (voir au dos de la
cartouche) qui puissent provoquer des
allergies.N'utilisez pas le gel et/ou la lotion si
vous êtes allergique à un ou plusieurs de ces
composants!
◗Si le cordon d'alimentation est endommagé,il
ne doit être remplacé que par Philips ou par
un Centre ServiceAgréé,pour éviter tout
accident.
Charge
Indications de charge
C◗Dès que vous commencez à charger le rasoir
vide,le témoin vert s'allumera.
◗Le témoin lumineux rouge clignotera si les
accumulateurs sont presque déchargés.
◗Si les accumulateurs sont presque déchargés,
le témoin rouge clignotera quelques secondes
lorsque vous arrêtez le rasoir.
Charger l'appareil
Chargez et maintenez l'appareil à une
température comprise entre 5cC et 35cC.
1Enfoncez la petite fiche dans le support de
charge et insérez la fiche du chargeur dans
la prise de courant.
FRANÇAIS 19

C2Mettez le rasoir dans le support de charge.
C3Pressez jusqu'à ce que vous entendiez un
clic.
Le rasoir s'arrête automatiquement lorsqu'il est
mis sur le support de charge.
4Lorsque vous chargez l'appareil pour la
première fois,ou si l'appareil n'a pas été
utilisé pendant une longue période:
chargez-le pendant 24 heures sans
interruption.
Une charge normale dure 8 heures environ.
A pleine charge,le rasoir offre une autonomie de
40 minutes environ.
Insérer la cartouche
Les cartouches de gel/lotion à raser NIVEA FOR
MEN sont disponibles en paquets contenant cinq
cartouches et une pompe en plastique.
Ne jetez pas la pompe quand vous remplacez la
cartouche vide.Vous en aurez besoin pour les
cinq cartouches.
Le gel/lotion d'une cartouche Philishave NIVEA
FOR MEN Cool Skin suffit pour environ 8/10
rasages.
FRANÇAIS20

Retirez la cartouche de l'appareil si vous ne vous
en servez pas pendant une semaine ou plus.
Utilisez exclusivement des cartouches Philishave
NIVEA FOR MEN (HQ160 et HQ161).
Pour des raisons hygiéniques,il est conseillé de
changer la pompe à chaque nouveau paquet de
cartouches.
Si vous êtes à court de cartouches et que vous
ne savez pas où les acheter,contactez le Service
Consommateurs de votre pays (voir "Garantie et
service").
Insérer la cartouche
C1Prenez une cartouche du paquet.Insérez la
pompe fournie avec le paquet dans la
cartouche jusqu'à ce que vous entendiez
un clic.
C2Poussez le bouton de déverrouillage vers
bas et ouvrez le couvercle du
compartiment à cartouche.
C3Glissez la cartouche avec la pompe dans le
rasoir.Elle est fixée correctement si la
partie blanche de la pompe est dirigée vers
le haut.
FRANÇAIS 21
12

4Fermez le couvercle (vous entendrez un
clic).
5Appuyez plusieurs fois sur le bouton jaune
jusqu'à ce que l'émulsion à raser
apparaisse.Le rasoir est prêt à l'emploi.
BValabilité du gel/lotion à raser NIVEA FOR MEN
des cartouches:32 mois si conservé(e) à une
température comprise entre 0cC et +40cC.
Utilisation de l'appareil
Rasage
Mettre l'appareil en marche
1Mettez le rasoir en marche en appuyant
sur le bouton marche/arrêt une fois.
C2Appuyez sur le bouton jaune de la pompe
pour appliquer le gel/lotion NIVEA FOR
MEN.
3Déplacez le rasoir sur la peau en
effectuant des mouvements rectilignes et
circulaires.
4Pendant le rasage,appuyez souvent sur le
bouton de la pompe pour appliquer le
gel/lotion NIVEA FOR MEN et permettre
ainsi au rasoir de glisser sur votre peau.
FRANÇAIS22