Philips HQ8260 User manual

3
A
B
C
D
E
G
F
H
I
M
LKJ
O
P
N
1
4222.002.4998.2.indd 3 27-02-2009 11:33:59

4
4222.002.4998.2.indd 4 27-02-2009 11:34:00

HQ8290CC, HQ8270CC, HQ8260CC
ENGLISH 6
DEUTSCH 29
ESPAÑOL 53
FRANÇAIS 77
ITALIANO 101
NEDERLANDS 125
PORTUGUÊS 149
TÜRKÇE 173
4222.002.4998.2.indd 5 27-02-2009 11:34:00

6
Introduction
Congratulations on your purchase and welcome
to Philips!To fully benefit from the support that
Philips offers, register your product at www.philips.
com/welcome.
Please read this user manual, as it contains
information about the wonderful features of this
shaver as well as some tips to make shaving easier
and more enjoyable.
Important
Read this user manual carefully before you use the
shaver and the Jet Clean System. Save the user
manual for future reference.
Danger
Make sure the adapter does not get wet.
Warning
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
The shaver and the Jet Clean System are not
intended for use by persons (including children)
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliances by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the shaver and the Jet Clean
System.
-
-
-
-
-
ENGLISH
4222.002.4998.2.indd 6 27-02-2009 11:34:01

Caution
Do not use the shaver or the Jet Clean System if
it is damaged.
Never immerse the shaver in water.
Charge, use and store the shaver at a temperature
between 10°C and 35°C.
Always put the protection cap on the shaver
to protect the shaving heads when you are
travelling.
The shaver, the Jet Clean System and the other
accessories are not dishwasher-proof.
Never use water hotter than 80°C to rinse the
shaver.
Do not use the shaver in the bath or in the
shower.
Only use the adapter supplied.
Never immerse the Jet Clean System in water nor
rinse it under the tap.
If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
Only use the Jet Clean System with the original
HQ200 cleaning fluid.
Use and store the Jet Clean System at a
temperature between 10°C and 35°C.
Always place the Jet Clean System on a stable,
level and horizontal surface to prevent leakage.
Always place the Jet Clean System on a fluid-
resistant surface.
The Jet Clean System thoroughly cleans but does
not disinfect your shaver, therefore do not share
the shaver with others.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH 7
4222.002.4998.2.indd 7 27-02-2009 11:34:03

Compliance with standards
The shaver complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap.
The shaver and the Jet Clean system comply with
all standards regarding electromagnetic fields
(EMF). If handled properly and according to the
instructions in this user manual, the appliances are
safe to use based on scientific evidence available
today.
General
The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Overview (Fig. 5)
AProtection cap
BShaving unit
CShaving unit release button
DShaver on/off button with power-on symbol
EDisplay
FTrimmer
GStorage pouch
HJet Clean System
ILocking lever
JCleaning symbol, drying symbol and ‘fluid low’
symbol
KJet Clean System on/off button
LCleaning chamber release button
MShaver holder
NCleaning brush
OAdapter
PSmall plug
-
-
-
ENGLISH8
4222.002.4998.2.indd 8 27-02-2009 11:34:04

The display
HQ8290: Before you use the shaver for the first
time, remove the protective foil from the display.
The three shaver types (HQ8290, HQ8270 and
HQ8260) have different displays, which are shown in
the figures below.
HQ8290
HQ8270
HQ8260
Charging
Charging takes approx. 60 minutes.
A fully charged shaver has a cordless shaving time
of up to 55 minutes, which is enough for approx. 17
shaves.
HQ8290
When the shaver is charging, the minutes
indication and the plug symbol flash.
The shaving minutes increase until the shaver is
fully charged.
-
-
-
-
-
ENGLISH 9
4222.002.4998.2.indd 9 27-02-2009 11:34:06

HQ8270/HQ8260
When the shaver is charging, the battery level
lights go on in a rising pattern as the battery
charges.
Battery fully charged
HQ8290
When the battery is fully charged, the minutes
indication is visible on the display and the plug
symbol disappears from the display.
Note:The actual shaving time is calculated by the
shaver. If you have a heavy beard, the shaving time may
be less than 55 minutes.The shaving time may also
vary over time, depending on your shaving behaviour,
cleaning habits and beard type.
After 4 hours of charging, the display automatically
switches off and the charging process stops.
HQ8270/HQ8260
When the battery is fully charged, all battery level
lights light up continuously.
After 4 hours of charging, the battery level lights
go out automatically and the charging process
stops.
Battery low
Note: If the rechargeable battery runs low during
shaving, you can connect the shaver to the mains to
finish the shave.
-
-
-
-
-
ENGLISH10
4222.002.4998.2.indd 10 27-02-2009 11:34:09

HQ8290
When the battery is almost empty (when
there are only 5 or fewer shaving minutes left),
the minutes indication and the plug symbol
start flashing.
When you switch off the shaver, the shaving
minutes and the plug symbol continue to flash for
a few more seconds.
HQ8270/HQ8260
When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the
orange plug symbol lights up.
When you switch off the shaver, the plug symbol
flashes for a few seconds.
Remaining battery capacity
The remaining battery capacity is shown when you
switch the shaver on or off:
HQ8290
The remaining battery capacity is indicated by the
number of shaving minutes shown on the display.
HQ8270/HQ8260
The remaining battery capacity is indicated by the
number of battery level lights that are on.
Travel lock
You can lock the shaver when you are going to
travel.The travel lock prevents the shaver from being
switched on by accident.
-
-
-
-
-
-
ENGLISH 11
4222.002.4998.2.indd 11 27-02-2009 11:34:10

Note:The travel lock cannot be activated when the
shaver is connected to the mains.
Activating the travel lock
1 Press the on/off button for 4 seconds to enter
the travel lock mode (your display may differ
from the one shown in the figure).
The lock symbol appears on the display and the
power-on symbol lights up for a few seconds to
indicate that the travel lock has been activated.
Note:When you push the on/off button during less
than 4 seconds while the shaver is in the travel lock
mode, the lock symbol and the power-on symbol in the
on/off button flash for a few seconds.
Deactivating the travel lock
1 Press the on/off button for 4 seconds.
The lock symbol disappears and the motor
starts running to indicate that the travel lock has
been deactivated.
The shaver is now ready for use again.
Note:When you start charging, the travel lock is
automatically deactivated.
Charging
It takes approx. 60 minutes to fully charge the
battery.
When you charge the shaver for the first time or
after a long period of disuse, let it charge for 4 hours.
Tip:To optimise the battery capacity, fully charge the
shaver and then use it normally until the battery is
completely empty. Repeat this process three times in a
row. If you optimise the battery capacity in this way, you
,
,
ENGLISH12
4222.002.4998.2.indd 12 27-02-2009 11:34:11