Philips Multigroom 5000 Series User manual

Always here to help you
Register your product and get support at
www.philips.com/welcome
QG3371

3 - 20
41 mm
1-18
15
14
13
12
11
1
2
4
3
5
6
7
8
9
10
1

QG3371
ENGLISH 6
БЪЛГАРСКИ 15
ČEŠTINA 24
EESTI 33
MAGYAR 42
ҚАЗАҚША 51
LIETUVIŠKAI 60
LATVIEŠU 69
POLSKI 78
ROMÂNĂ 87
РУССКИЙ 96
SLOVENSKY 106
SLOVENŠČINA 115
SRPSKI 124
УКРАЇНСЬКА 133

6
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Mini foil shaver
2 Nose/ear hair trimmer
3 Hair clipper
4 Full metal precision trimmer
5 Full metal beard trimmer
6 Handle
7 On/off button
8 TURBO button
9 Battery status indicator/Turbo LED
10 Storage pouch
11 Small plug
12 Adapter
13 Cleaning brush
14 Beard and moustache comb (1-18mm)
15 Hair clipping comb (3-20mm)
Important
Read this user manual carefully before you use the appliance and save it
for future reference.
Danger
- Keep the adapter dry.
Warning
- Check if the voltage indicated on the adapter corresponds to the local
mains voltage before you connect the appliance.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
- Keep the appliance and its cord out of the reach of children.
Caution
- Use, charge and store the appliance at a temperature between
5°C and 35°C.
- Only use the adapter supplied to charge the appliance.
- If the appliance is subjected to a major change in temperature, pressure
or humidity, let the appliance acclimatise for 30 minutes before you use it.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- Always check the appliance before you use it. Do not use the appliance
if any of its parts is damaged or broken, as this may cause injury.
ENGLISH

Compliance with standards
- This appliance complies with the internationally approved IEC Safety
regulations and can be safely cleaned under the tap.
- This Philips appliance complies with all standards regarding
electromagnetic elds (EMF). If handled properly and according to the
instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.
Charging
Charging takes approximately 1 hour. When the appliance is fully charged,
it has an operating time of up to 50 minutes.When the battery status
indicator lights up orange, the battery is running low (approx. 10 minutes of
operating time left) indicating you need to recharge the appliance soon.
Note:You can also quick charge the appliance, a 5 minute charge equals
approx. 5 minutes of operating time.
1 Switch off the appliance before you charge it.
2 Insert the small plug into the appliance.
3 Put the adapter in the wall socket.
Using the appliance
The appliance is equipped with a turbo power boost for fast results and a
memory function that remembers the last used speed setting.
Hair clipping
Preparing for hair clipping
1 Make sure that the head of the person whose hair you intend to cut
is at the same level as your chest.This ensures that all parts of the
head are clearly visible and within easy reach.
2 Comb the hair in the growth direction.
Hair clipping with hair clipping comb
1 Place the hair clipper on the handle (1) and turn it clockwise to
x it (2).
1
2
ENGLISH 7

2 Slide the hair clipping comb into the guiding grooves on both sides of
the handle.
3 Press the setting selector (1) and slide the comb to the desired hair
length setting (2).
You can choose any setting between 3 and 20mm in steps of 1mm.
Tip:Write down the hair length settings you selected to create a
certain hairstyle as a reminder for future clipping sessions.
4 Switch on the appliance.
5 Move the appliance slowly and against the direction of hair growth.
Press lightly.
Note: Since hair grows in different directions, you need to move the appliance
in different directions as well (upward, downward or across).
6 Always make sure that the at part of the comb is in full contact
with the scalp to obtain an even result.
Make overlapping passes over the head to ensure that you cut all the hair
that needs to be cut.
Note: When you trim for the rst time, start at the highest setting (20mm)
to familiarise yourself with the appliance.
Hair clipping without hair clipping comb
You can use the trimmer without comb to clip hair very close to the skin
(to a length of 1mm) or to create contours.
Caution: Be careful when you clip without the comb because the
trimmer removes every hair it comes in contact with.
3 - 20
2
3 - 20
1
ENGLISH8

1 Press the setting selector (1) and slide the comb upwards (2).
Then pull the comb off the appliance (3).
2 Before you start to contour the hairline around the ears,
comb the hair ends over the ears.
3 Tilt the appliance in such a way that only one edge of the trimmer
touches the hair.
Only cut the hair ends.The hairline should be close to the ear.
4 To contour the neckline and sideburns, turn the appliance and make
downward strokes.
5 Move the appliance slowly and smoothly. Follow the natural hairline.
Beard trimming
When you trim your beard for the rst time, be careful. Do not move the
trimmer too fast. Make smooth and gentle movements.
Beard trimming with the beard and moustache comb
1 Place the beard trimmer on the handle (1) and turn it clockwise
to x it (2).
2 Slide the beard and moustache comb into the guiding grooves on
both sides of the handle.
3 - 20
1
3
2
1
2
ENGLISH 9

3 Press the setting selector (1) and slide the comb to the desired hair
length setting (2).
You can choose any setting between 1 and 18mm in steps of 1mm.
4 Switch on the appliance.
5 Slowly move the trimmer against the hair growth direction. Press
lightly and always make sure the surface of the comb is in full contact
with the skin.
Note: When you trim for the rst time, start at the highest setting
(18mm) to familiarise yourself with the appliance.
Styling/contouring your beard
You can use the precision trimmer to cut shapes in beard hair or scalp hair.
It cuts hair very close to the skin (to a length of 1mm).
Caution: Be careful when you use the precision trimmer because it
removes every hair it comes in contact with.
1 Place the precision trimmer on the handle (1) and turn it clockwise
to x it (2).
2 To achieve a good cutting result, move the precision trimmer against
the direction of hair growth.Always make sure the precision trimmer
is in full contact with the skin.
3 Make careful and controlled movements with the precision trimmer.
Tip: For the perfect nish, you can use the mini foil shaver to make the edges
and lines of your beard style even smoother.
1
2
1
2
ENGLISH10