Philips Flaors 848390207 User manual

Please confirm content
Register your product and get suppor t at
www.philips.com/avors
FTS6000
EN Home Theatre System 5
IT Sistema Home Theater 49
1_fts6000_12_eng3_final.indd 11_fts6000_12_eng3_final.indd 1 2008-09-03 11:54:56 AM2008-09-03 11:54:56 AM

2
Important notes for users in U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
Remove fuse cover and fuse.1.
Fix new fuse which should be a BS13622.
5 Amp, A.S.T.A. or BSI approved type.
Ret the fuse cover.3.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should have
a value of 5 Amp. If a plug without a fuse is
used, the fuse at the distribution board should
not be greater than 5 Amp.
Note: The severed plug must be disposed off to
avoid a possible shock hazard should it be inserted
into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the
following code: blue = neutral (N),
brown = live (L).
As these colours may not correspond with•
the colour markings identifying the terminals
in your plug, proceed as follows:
Connect the blue wire to the terminal•
marked N or coloured black.
Connect the brown wire to the•
terminal marked L or coloured red.
Do not connect either wire to the earth•
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er derfor
ikke frakoplet nettet så lenge apparatet er
tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio FTS6000, Philips
risponde alle prescrizioni dell’art. 2 comma 1 del
D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Lifestyle
Philips, Glaslaan 2 5616 JB Eindhoven,
The Netherlands
1_fts6000_12_eng4+addendum.indd 21_fts6000_12_eng4+addendum.indd 2 10/15/2008 10:10:02 AM10/15/2008 10:10:02 AM

3
‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD
DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.’
DK
Advarsel: Usynlig laserstråling ved åbning når
sikkerhedsafbrydere er ude af funktion. Undgå
utsættelse for stråling.
Bemærk: Netafbryderen er sekundært
indkoblet og ofbryder ikke strømmen fra
nettet. Den indbyggede netdel er derfor
tilsluttet til lysnettet så længe netstikket sidder i
stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat
sätt än i denna bruksanvisning specificerats, kan
användaren utsättas för osynlig laserstrålning,
som överskrider gränsen för laserklass 1.
Observera! Stömbrytaren är sekundärt kopplad
och bryter inte strömmen från nätet. Den
inbyggda nätdelen är därför ansluten till elnätet
så länge stickproppen sitter i vägguttaget.
SF
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen muulla kuin
tässä käyttöohjeessa mainitulla tavalla saattaa
altistaa käyttäjän turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei saa olla
alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkko-osa on
kytkettynä sähköverkkoon aina silloin, kun
pistoke on pistorasiassa.
1_fts6000_12_eng3_final.indd 31_fts6000_12_eng3_final.indd 3 2008-09-03 11:54:58 AM2008-09-03 11:54:58 AM

4
LASER
Type Semiconductor laser
GaAIAs
Wave length 650 - 660 nm (DVD)
784 - 796 nm (CD)
Output Power 6 mW (DVD)
7 mW (VCD/CD)
Beam divergence 60 degrees
•
•
•
•
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the double-D
symbol are registered trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital
Surround are registered trademarks and the
DTS logos and Symbol are trademarks of DTS,
Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
DivX, DivX Ultra Certified, and associated logos
are trademarks of DivX, Inc. and are used under
license.
Official DivX® Ultra Certified product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media files and the DivX® Media Format.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
CLASS 1
LASER PRODUCT
1_fts6000_12_eng3_final.indd 41_fts6000_12_eng3_final.indd 4 2008-09-03 11:54:58 AM2008-09-03 11:54:58 AM

English
EN 5
Contents
Contents
1 Important 6
Safety and important notice 6
2 Your product 7
Features highlight 7
Product overview 8
3 Connect 11
Place the unit 11
Connect video cables 12
Connect speakers to subwoofer 14
Connect subwoofer and radio antenna 14
Connect audio cables/other devices 15
Mount Flavors frames 17
Attach table stand to the main unit 17
Mount the DVD Home Theatre
unit/speakers 18
4 Get started 19
Prepare the remote control 19
Find the correct viewing channel 20
Select menu display language 20
Turn on Progressive Scan 21
Activate EasyLink control 22
Select a play source 23
5 Play 24
Play from disc 24
Play video 25
Play music 29
Play photo 30
Play from USB device 31
Play from portable media player 32
Play from radio 32
6 Adjust sound 35
Control the volume 35
Select surround sound 35
Select a preset sound effect 35
7 Adjust settings 36
General setup 36
Audio setup 38
Video setup 39
Preferences 42
8 Additional information 44
Update software 44
Care 44
Specifications 45
9 Troubleshooting 46
10 Glossary 48
1_fts6000_12_eng3_final.indd 51_fts6000_12_eng3_final.indd 5 2008-09-03 11:54:59 AM2008-09-03 11:54:59 AM

6EN
Recycle notice
Your product is designed and manufactured
with highly quality material and components,
which can be recycled and reused. When this
crossed-out wheeled bin symbol is attached to
a product, it means the product is covered by
the European Directive 2002/96/EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products. Please act according to your local
rules and do not dispose your old products
with your normal household waste. The
correct disposal of your old product will help to
prevent potential negative consequences for
the environment and human health.
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
1 Important
Safety and important notice
Warning!
Risk of fire or electric shock!
Ensure that air can circulate freely through the
ventilation holes on this unit. Allow at least 5~10 cm
clearance around the unit.
Never expose this unit to direct sunlight, naked
flames or heat.
Never place this unit on other electrical equipment.
Keep away from this unit during lightning storms.
Never remove the casing of this unit. Please leave all
maintenance work to qualified personnel.
Keep this unit away from water, moisture and liquid-
filled objects.
•
•
•
•
•
•
Caution!
Remove batteries if they are exhausted or if the
remote control is not to be used for a long time.
Do not mix batteries (old and new or carbon and
alkaline, etc.).
Batteries contain chemical substances, they should
be disposed of properly.
Visible and invisible laser radiation when open.
Avoid exposure to beam.
Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device
shall remain readily operable.
•
•
•
•
•
This product complies with the radio
interference requirements of the European
Community. This product complies with the
requirements of the following directives and
guidelines: 2006/95/EC, 2004/108/EC.
1_fts6000_12_eng3_final.indd 61_fts6000_12_eng3_final.indd 6 2008-09-03 11:54:59 AM2008-09-03 11:54:59 AM

English
EN 7
Your product
2 Your product
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
This DVD Home Theatre is designed to
complement your home perfectly. Enjoy the
DVD Home Theatre with 2.1-channel surround
sound and excellent picture quality.
Features highlight
Video upscaling to 1080p
You can now watch the DVDs in the highest
picture quality available for your HDTV. This
DVD Home Theatre offers full high-definition
video playback up to 1080p resolution for an
amazing viewing experience. A highly detailed
picture and increased sharpness delivers a more
true-to-life picture.
EasyLink
EasyLink uses the HDMI CEC (Consumer
Electronics Control) industry standard protocol
to share functionality with all HDMI CEC
compliant devices over HDMI. It enables the
connected devices to control each other with a
single remote control.
Note
Philips does not guarantee 100% interoperability
with all HDMI CEC devices.
•
USB direct and MP3 link
Simply plug your USB device into the USB
socket to play your MP3/WMA/JPEG/DivX files;
or plug your portable media player to the MP3
LINK socket to enjoy the music play in superb
sound quality.
Sync the audio output with the video play
This DVD Home Theatre provides you the
feature of delaying the audio output if the video
signals that go directly to the TV is slower than
the audio streams.
Region codes
DVD movies are usually not released at the
same time in all regions of the world, thus all
DVD players are programmed to a specific
region code.
Countries DVD region code
Europe
ALL
Russia
ALL
1_fts6000_12_eng3_final.indd 71_fts6000_12_eng3_final.indd 7 2008-09-03 11:55:00 AM2008-09-03 11:55:00 AM

8EN
Product overview
Main unit
a2 (Standby-on)
Turn on this unit or turn off to standby
mode.
bSOURCE
Select a play media: DISC, FM, AUX,
DI (Digital Input) or MP3 LINK.
cPLAY/PAUSE u
Start or pause disc play.
RADIO: start auto radio installation
(only available for first time setup).
dVOLUME +-
Adjust the volume level.
eDisplay panel
fDisc compartment
gOPEN/CLOSE Z
Open or close the disc compartment.
•
•
•
•
•
•
hFM radio antenna socket
To connect radio antenna.
iAUX IN socket
To connect audio output from other
device to route its sound output to this
unit.
j(USB) socket
To connect USB flash drive, USB
memory reader or digital camera.
kMP3 LINK socket
To connect portable audio player.
•
•
•
•
1234568
7
9
10
11
1_fts6000_12_eng3_final.indd 81_fts6000_12_eng3_final.indd 8 2008-09-03 11:55:00 AM2008-09-03 11:55:00 AM

English
EN 9
Your product
Remote control
9
1
2
4
5
6
7
8
10
3
20
19
18
17
13
14
15
16
12
11
a2
Turn on this unit or turn off to standby
mode.
Press and hold to turn off this unit and
all the HDMI CEC compliant TV/
devices (for EasyLink control only).
bZ (Open/Close)
Open or close the disc compartment.
cREPEAT / PROGRAM
Select various repeat or shuffle modes;
turns off repeat or shuffle mode.
RADIO: press this button to start
manual radio preset.
RADIO: press and hold this button to
start automatic radio preset.
dZOOM
Zoom in or out the picture on the TV.
eINFO
Display the current status or disc
information.
Display photo files in 12 thumbnails
view.
fOPTIONS
Access or exit Options menu (this
menu provides various setting options).
gu(Play/Pause)
Start or pause disc play.
RADIO: start auto radio installation
(only available for first time setup).
hx(Stop)
Stop disc play.
RADIO: erase the current preset radio
station.
iSOUND MODES +-
Select a predefined sound effect.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1_fts6000_12_eng3_final.indd 91_fts6000_12_eng3_final.indd 9 2008-09-03 11:55:00 AM2008-09-03 11:55:00 AM

10 EN
jAUDIO/SYNC
Select an audio language/channel.
Press and hold to access audio sync
setting. Then press VOL +- to set
the audio delay time.
kSource buttons
AUX / MP3 LINK: switch to AUX, DI
(Digital Input) or MP3 LINK that
corresponds to the socket you used to
connect the external device.
USB / RADIO: press repeatedly to
switch to USB or FM mode.
DISC: switch to DISC mode.
lOK
Confirm an entry or selection.
mCursor buttons (vVb B)
Navigate through the on-screen menu.
Press left or right for fast forward and
backward search.
RADIO:press up or down to tune the
radio frequency.
RADIO: press left or right to start auto
search.
nBACK 
Return to the previous display menu.
For DVD, go to title menu.
For VCD version 2.0 or SVCD with
PBC turned on: return to the menu
during playback.
oí/ë(Previous/Next)
Skip to the previous or next title/
chapter/track.
RADIO: select a preset radio station.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
pH(Mute)
Mute or restore the volume.
qVOL +-
Adjust the volume level.
rSURROUND
Switch audio output to Dolby virtual
surround or stereo sound.
sNumeric buttons
Enter a preset number or item to play.
tSUBTITLE
Select DVD or DivX subtitle language.
•
•
•
•
•
1_fts6000_12_eng3_final.indd 101_fts6000_12_eng3_final.indd 10 2008-09-03 11:55:01 AM2008-09-03 11:55:01 AM

English
EN 11
Connect
3 Connect
This section describes the basic connections
required for this DVD Home Theatre unit
before it can be used.
Basic connections:
Place the unit
Connect video cables
Connect speakers to subwoofer
Connect subwoofer and radio antenna
Optional connections:
Connect audio cables/other devices
Connect audio from TV
Connect audio from cable box/
recorder/game console
Connect portable media player
Connect USB device
Mount Flavors frames
Attach table stand to the main unit
Mount the DVD Home Theatre unit/
speakers
Note
Refer to the type plate at the rear or bottom of the
product for identification and supply ratings.
Before you make or change any connections, ensure
that all the devices are disconnected from the power
outlet.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Place the unit
For optimum performance, place this unit
on top of a table or mount it on the wall.
Never place this unit in an enclosed cabinet.
Install this unit near the AC outlet where
the AC power plug can be easily reached.
RIGHT
LEFT
1 Place this DVD Home Theatre unit near to
the TV.
Attach the table stand to the DVD
Home Theatre unit before place it on a
table top.
2 Place the speakers at the normal listening
ear-level and directly parallel to the
listening area.
3 Place the subwoofer at the corner of the
room or at least one metre away from the
TV.
Note
To avoid magnetic interference or unwanted noise,
never place the speakers too close to the TV or any
radiation devices.
•
•
•
•
•
1_fts6000_12_eng3_final.indd 111_fts6000_12_eng3_final.indd 11 2008-09-03 11:55:01 AM2008-09-03 11:55:01 AM

12 EN
Connect video cables
This section describes how to connect this
DVD Home Theatre unit to your TV so to
enable viewing of disc play.
Select the best video connection that your TV
can support.
Option 1: Connect to HDMI socket (for a
HDMI, DVI or HDCP-compliant TV).
Option 2: Connect to Scart socket (for a
standard TV).
Option 3: Connect to component video
socket (for a standard TV or Progressive
Scan TV).
Option 4: Connect to Video socket (for a
standard TV).
Note
You must connect this unit directly to a TV.•
Option 1: Connect to HDMI socket
HDMI IN
HDMI OUT
1 Connect a HDMI cable (supplied) from the
HDMI OUT on this unit to the HDMI IN
socket on your TV.
•
•
•
•
Note
The HDMI connector is only compatible with HDMI
compliant TVs and DVI-TVs.
•
Tips
To optimise the video output, see chapter ‘Adjust
settings’ > [ Video Setup ] > [ HDMI Setup ] for
details.
This unit is HDMI CEC compatible. It enables
connected TV/device to control each other over
HDMI, see chapter ‘Activate EasyLink control’ for
details.
Use a HDMI/DVI adaptor in case your TV has only
a DVI connection. An extra audio connection is
needed to complete this connection.
This type of connections provide best picture quality.
•
•
•
•
Option 2: Connect to Scart socket
SCART
VIDEO OUT
1 Connect the scart converter cable
(supplied) from the VIDEO OUT socket
on this unit to the scart input socket on
your TV.
1_fts6000_12_eng3_final.indd 121_fts6000_12_eng3_final.indd 12 2008-09-03 11:55:01 AM2008-09-03 11:55:01 AM

English
EN 13
Connect
Option 3: Connect to component
video socket
COMPONENT VIDEO OUT
1Connect the component video cables (not
supplied) from the Y PBPRsockets on this
unit to the component video input sockets
on your TV.
If a progressive scan TV is used, you
may turn on the progressive scan mode
(see chapter ‘Turn on Progressive Scan’
for details).
Tips
The component video input socket on your TV may
be labelled as Y Pb/Cb Pr/Cr or YUV.
This type of connections provide good picture
quality.
•
•
•
Option 4: Connect to Video socket
VIDEO IN
VIDEO OUT
1 Connect a composite video cable (not
supplied) from the VIDEO OUT socket on
this unit to the video input socket on your
TV.
Tips
The video input socket on your TV may be labelled
as A/V IN, VIDEO IN, COMPOSITE or BASEBAND.
This type of connections provide standard picture
quality.
•
•
1_fts6000_12_eng3_final.indd 131_fts6000_12_eng3_final.indd 13 2008-09-03 11:55:01 AM2008-09-03 11:55:01 AM

14 EN
Connect speakers to
subwoofer
LEFT
RIGHT
1 Connect the left and right speakers to the
matching sockets on the subwoofer.
Note
Ensure that the front portion of the plug is fully
inserted into the socket.
•
Connect subwoofer and radio
antenna
1
3
2
1 Connect the interconnect cable (supplied)
from the TO SUBWOOFER socket on
this unit to the TO MAIN UNIT socket on
the subwoofer.
2 Connect the FM antenna (supplied) and
FM extension cable (supplied) to the
FM75Ωsocket. Extend the FM antenna
and fix its ends to the wall.
3 Connect the power cord when all the
required connections are complete and
you are ready to enjoy this DVD Home
Theatre unit.
1_fts6000_12_eng3_final.indd 141_fts6000_12_eng3_final.indd 14 2008-09-03 11:55:02 AM2008-09-03 11:55:02 AM

English
EN 15
Connect
Connect audio cables/other
devices
This section describes how you can route the
sound from other devices to this DVD Home
Theatre unit in order to enjoy sound output or
audio play with surround capabilities.
Connect audio from TV
(also used for EasyLink control)
Connect to optical socket
OPTICAL
DIGITAL IN
SPDIF OUT
(Optical)
1 Connect an optical cable (supplied) from
the DIGITAL IN-OPTICAL socket on this
unit to the SPDIF OUT/OPTICAL OUT
socket on your TV.
Note
To listen to the audio output from this connection,
press AUX / MP3 LINK repeatedly until ‘DI’ is
displayed on the display panel.
•
Connect audio from cable box/
recorder/game console
AUX IN
1 Connect an audio cable (supplied) from
the AUX IN socket on this unit to the
AUDIO OUT sockets on the device.
Note
To listen to the audio output from this connection,
press AUX / MP3 LINK repeatedly until ‘AUX’ is
displayed on the display panel.
To route the audio from your TV to this DVD Home
Theatre unit, connect an audio cable from the audio
input on this unit to the audio output on your TV.
•
•
1_fts6000_12_eng3_final.indd 151_fts6000_12_eng3_final.indd 15 2008-09-03 11:55:02 AM2008-09-03 11:55:02 AM

16 EN
Connect portable media player
MP3 LINK
MP3
1 Connect a 3.5mm stereo audio cable
(supplied) from the MP3 LINK socket on
this unit to the phone socket on your
portable media player (such as MP3 player).
Note
To listen to the audio output from this connection,
press AUX / MP3 LINK repeatedly until ‘MP3 LINK’
is displayed on the display panel.
•
Connect USB device
1 Connect the USB device to (USB)
socket on this unit.
Note
This DVD Home Theatre unit can only play/view
MP3, WMA, DivX (Ultra) or JPEG files that are
stored on such devices.
To listen to the audio output from this connection,
press USB.
•
•
1_fts6000_12_eng3_final.indd 161_fts6000_12_eng3_final.indd 16 2008-09-03 11:55:02 AM2008-09-03 11:55:02 AM

English
EN 17
Contents
Mount Flavors frames
A
B
A Decorative frames
B Finger slot
Note
To avoid damage to the unit, ensure that it is
placed on a stable surface before you carry out the
following actions.
•
1 Place the main unit and speakers with the
front panel facing up on a flat surface.
2 Align the frames with the front of the unit/
speakers.
3 Mount the frames.
To remove frame from the main unit,
pull off the frame using the finger slot.
•
Attach table stand to the
main unit
1 Ensure all the required cables are
connected to this unit.
2 Place the main unit with the front panel
facing down on a flat surface.
3 Attach the table stand to the rear of this
unit and slide it to the left to lock into
position.
To remove the table stand, hold the
bottom of the stand and slide it to the
right.
C

C table stand
Note
Do not attach the table stand if you want to mount
this unit on the wall.
•
•
1_fts6000_12_eng3_final.indd 171_fts6000_12_eng3_final.indd 17 2008-09-03 11:55:03 AM2008-09-03 11:55:03 AM

18 EN
Mount the DVD Home
Theatre unit/speakers
Caution!
Risk of personal injury and damage to the unit.
Allow only qualified persons to mount the unit.
•
1 Ensure all the required cables are
connected to this unit.
2 Drill the screw holes and insert the rubber
wall plugs (not supplied) into the holes.
Use the supplied mounting guide for
accurate screw positions.
•
Before you mount the speaker, remove
its stand by pressing on the catches (A)
and pull it out.
A
3 Hook the DVD Home Theatre unit/
speakers firmly onto the screws.
Note
The height of the screw positions is 23.5mm
difference between the main unit and the speakers.
•
•
1_fts6000_12_eng3_final.indd 181_fts6000_12_eng3_final.indd 18 2008-09-03 11:55:04 AM2008-09-03 11:55:04 AM

English
EN 19
Get started
4 Get started
Prepare the remote control
1 Push to open the battery compartment
cover.
2 Insert two batteries type R03 or AAA.
Match the indications (+-) inside the
battery compartment.
3 Close the cover.
Note
If you are not going to use the remote control for a
long time, remove the batteries.
•
Control a play source
1 Select the source you wish to control by
pressing the DISC, USB/RADIO or
AUX/MP3 LINK button.
2 Then select the desired function (for
example í, ë).
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this unit and select the
desired function.
2 Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button Action
v V Move up or down.
b B Move left or right.
Confirm a selection.
Enter numbers.
1_fts6000_12_eng3_final.indd 191_fts6000_12_eng3_final.indd 19 2008-09-03 11:55:04 AM2008-09-03 11:55:04 AM

20 EN
Find the correct viewing
channel
1 Press 2to turn on the DVD Home
Theatre unit.
2 Press DISC to switch to disc mode
3 Turn on the TV and switch it to the
correct video-in channel.
You may go to the lowest channel on
your TV, then press the Channel Down
button on your TVs remote control
until you see the Video In channel.
You may press °button repeatedly
on your TVs remote control.
Usually this channel is between the
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Tips
See TVs user manual on how to select the correct
input on your TV.
•
•
•
•
Select menu display language
Note
You can skip this setting if this unit is connected to a
HDMI CEC compliant TV. It switches automatically
to the same OSD menu language as per your TV
setting.
•
1 Press DISC.
2 Press OPTIONS.
[ General Setup ] menu is displayed.
3 Press B.
4 Press vV to select [ OSD Language ] in
the menu, then press B.
General Setup
Screen Saver
DivX(R) VOD Code
Sleep
Display Dim
Disc Lock
OSD Language
English
Deutsch
Dansk
Français
Italiano
Nederlands
Auto
Suomi
Themes
The language options are different
depending on your country or region.
It may not correspond to the illustration
shown here.
5 Press vV to select a language, then press
OK.
Tips
To set the default language for DVD audio and disc
menu, see chapter ‘Adjust settings’ - [ Preferences ]
for details.
•
•
1_fts6000_12_eng3_final.indd 201_fts6000_12_eng3_final.indd 20 2008-09-03 11:55:05 AM2008-09-03 11:55:05 AM