Philips BTM177/12 User manual

CR2025
Quick Start Guide
Step B
Step A
Enjoy
Setup
1
Quick Start Guide
What’s in the Box?
You should find these items upon opening the box.
FM antenna
Quick Start Guide
Pull out the insulation
plastic sheet.
2
User Manual
User manual
Remote Control
BTM177
BTM177_12_QSG_Eng 2/28/08, 13:571

Step A Setup
1
2
3
Connection
5
1
3
4
Setting the clock
For radio reception, connect the supplied FM antenna to the
FM ANTENNA terminal.
Connect the speaker wires to the SPEAKERS terminals.
Connect the power cord of the system to the AC power outlet.
In standby mode, press DISPLAY/CLOCK.
Press ALBUM/PRESET +/- to select the hour.
Press DISPLAY/CLOCK to confirm.
Repeat steps 4-5 to set minute.
3
29
1
2
2Press ALBUM/PRESET +/- to select between 12 hour and 24 hour display.
Tips:
– See the User Manual for
how to connect other
equipment to this system.
– Use the supplied AC power
adaptor only! Using any other
power connection device may
damage your main set!
Speaker
(right)
Speaker
(left)
FM wire antenna
Power adaptor
Press DISPLAY/CLOCK again to confirm.
6
BTM177_12_QSG_Eng 2/28/08, 13:572

1
2
3
4
5
Tip:
Detailed playback features and
additional functions are described in
the accompanied owner's manual.
Step B Enjoy
Playing a disc
1
2
Select FM source.
Press PROG on the remote control for more than two seconds to program all available stations
in order of waveband.
Pressí/ ëon the set (ALBUM/PRESET +/- on the remote control ) until the desired preset station is
displayed
Programming and tuning to radio stations
3
Select CD source.
Press OPEN/CLOSE on the top of the system to open the CD door.
Insert a disc with the printed side facing up and press down
on OPEN/CLOSE to close the CD door.
PressÉÅto start playback.
Press 9to stop playback.
Notes for the remote control:
– First, select the source you wish to
control by pressing one of the source select
keys on the remote control (CDor AUX, for
example).
–Then select the desired function ( 2;,
í, ëfor example).
BTM177_12_QSG_Eng 2/28/08, 13:573

Step B Enjoy
CRoyal Philips Electronics N.V. 2008
All rights reserved.
http://www.philips.com PDCC-JW-0809
Playing a USB mass storage device
1
2
3
4
5
Make sure that your BTM177 is being powered on.
Press SOURCE repeatedly (or USB on the remote) to enter USB mode.
The LCD display shows USB.
Plug a compatible USB mass storage device to BTM177’s USB port marked .
If needed, use a suitable USB cable to connect between the device and BTM177’s USB port.
The device will automatically power on.
PressÉÅon your BTM177 to start playback.
Press 9to stop playback.
Tip:
Refer to the user manual supplied for
the description about compatibility of
USB mass storage device, and
playability of the files stored on the
USB device.
Operating a Bluetooth-enabled device via the system
1
2
3
4
5
Place a Bluetooth-enabled device for pairing within 10 meters from the system.
Press SOURCE on the top of the system (or BLUETOOTH on the remote control) to select the
Bluetooth source.
Press and hold PAIRING on the top of the system or the remote control for more than 3
seconds.
Set the Bluetooth-enabled device to search for other available Bluetooth devices until it recognizes “PHILIPS
BTM177”.
Select “PHILIPS BTM177” and wait until you hear a double beep from the system and the Bluetooth icon
turns on.
➜Enter “0000” when prompted for a keyword.
For a paired HFP and/or HSP mobile phone, you can receive, reject or hold a call via the system with the
PAIRING , and 9buttons respectively.
●For a paired A2DP device, you can enjoy music from it with the ÉÅ, ¡ / ™, S/Tand 9buttons
via the system.
6
BTM177_12_QSG_Eng 2/28/08, 13:574