Philips 109P2 CM25 GSIII User manual

Important Safety Notice ...................2
Technical Data...........................3
Installation ..............................4
OSD Adjustment .........................5
OSD lock & service modes.................6
Warning and Notes .......................7
DDCDATA..............................8
DDC Instructions.........................9~12
Electrical Adjustments ....................13~15
Purity and Static convergence Adjustments . . 16
Mechanical Instructions ...................17
Safety Test Requirements (Hipot & Ground) . . 18
Wiring Diagram ..........................19
Block Diagram ...........................20
Terminal(A1) Schematic Diagram & PCB (A1)...21
Video(A2) Schematic Diagram & PCB (A2).......22
Deflection(B) Schematic Diagram....................23
Waveforms (A, B, C)........................................24
PCB (B, C)..................................................... 25
Power Board(Diagram C) & Control Panel ........26
Driver(D) Schematic Diagram & PCB (D)..........27
Sensor(E) Schematic Diagram & PCB (E).........28
Repair Tips ....................................................29
Exploded View................................................30
Recommended Parts List.................................31
Spare Parts List...............................................32~39
Repair flow chart..............................................40~47
General Product Specification..........................48~78
Description Description
Page Page
Table of Contents
19" Auto scan Colour Monitor
DDC/Power saving/TCO
CHASSIS: CM25
Horizontal frequencies
30 - 111kHz
Service
Service
Service
Published by BCU Monitors Printed in Taiwan Copyright reserved Subject to modification Sep. 15 2000
©GB 3138 106 10118
109P20/00(PHILIPS)
109P2 CM25 GSIII
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.

Important Safety Notice
Proper service and repair is important to the safe, reliable operation
of all Philips Company** Equipment. The service procedures
recommended by Philips and described in this service manual are
effective methods of performing service operations. Some of these
service operations require the use of tools specially designed for
the purpose. The special tools should be used when and as
recommended.
It is important to note that this manual contains various CAUTIONS
and NOTICES which should be carefully Read in order to minimize
the risk of personal injury to service personnel. The possibility exists
that improper Service methods may damage the equipment. It also is
important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. Philips could not possibly know, evaluate and
advise the service trade of all conceivable ways in which service
might be done or of the possible hazardous consequences of each
way. Consequently, Philips has not undertaken any such broad
evaluation. Accordingly, a servicer who uses a service procedure or
tool which is not recommended by Philips must first satisfy himself
thoroughly that Neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
* * Hereafter throughout this manual, Philips Company will be
referred to as Philips.
Critical components having special safety characteristics are
identified with a by the Ref. No. in the parts list and enclosed
within a broken line* (where several critical components are grouped
in one area) along with the safety symbol on the schematics or
exploded views.
Use of substitute replacement parts which do not have the same
specified safety characteristics may create shock, fire, or other
hazards.
Under no circumstances should the original design be modified or
altered without written permission from Philips. Philips assumes no
liability, express or implied, arising out of any unauthorized
modification Of design.
Servicer assumes all liability.
WARNING
* Broken Line
FOR PRODUCTS CONTAINING LASER :
Invisible laser radiation when open.
AVOID DIRECT EXPOSURE TO BEAM.
Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
The use of optical instruments with this
product will increase eye hazard.
DANGER-
CAUTION-
CAUTION-
TO ENSURE THE CONTINUED RELIABILITY OF THIS
PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR
PART NUMBERS IN THE PARTS LIST SECTION OF THIS
SERVICE MANUAL.
2109P2 GS3 CM25
9Go to cover page
Forward
Back

3
Technical Data
Technical Specification*
CRT
Size and deflection :19 inch/46cm,90 defection angle
Dot pitch/Grille pitch : 0.24mm
Tube type :
Phosphor : P22
Recommended display
area : 14.0"x10.4"/355 x 265 mm
Maximum display area : 14.4"x10.8"/365 x 274 mm
Scanning
Horizontal scanning : 30 - 111 KHz
Vertical : 50 - 160 Hz
Video
Video dot rate : 261 Mhz
Input impedance
-Video : 75 Ohm
- Sync : 2.2 kOhm
Input signal levels : 0.7Vpp
Separate sync
Sync polarities : Positive and negative
O
: Composite sync
Aperture grille, flat, high
contrast, anti-glare, anti-static,
anti reflection, light
transmission 41%
scanning
Sync input signal
Pin assignment :
The 15-pin D-sub connector(male) of the signal cable
(IBM systems) :
Assignment Assignment
Pin No. Pin No.
Identification output -
Connected to pin 10
Identification output -
Connected to pin 10
Blue video input
2
7
6
8
4
5
3
19
12
11
14
13
15
10
Red video ground
Blue video ground
Green video ground
Ground
No pin
Logic ground
Data clock line(SCL)
V.Sync(VCLK for DDC)
H.Sync /H+V
Serial data line(SDA)
Green video input
Red video input
1
10
6
11 15
5
If you have VESA's DPMS compliance display card or
software installed in your PC,the monitor can automaticlly
reduce its power consumption when not in use. And if an
input from a keyboard, mouse or other input devices is
detected, the monitor will automatically "wake up". The
following table shows the power consumption and
signalling of this automatic power saving features :
Automatic Power Saving
Power Management Definition
Active
Amber
Yellow
Green
Yellow
Blanked
Blanked
Blanked <3W 97 %
95 %
95 %
0%
<6W
<6W
Typical
120W
Suspend
ON
OFF No
No
No
No
Yes
Yes
Yes Yes
Stand-by
V-SYNC POWER
SAVING( % )
POWER
USED
LED
COLOR
H-SYNC
VIDEO
VESA’s mode
This monitor is Energy Star compliant .As an ENERGY STAR
Partner, PHILIPS has determined that this product meets the
ENERGY STAR guidelines for energy efficiency.
White Color Temperature
Chromaticity CIE coordinates:
at 9300 k x = 0.283 y = 0.297
6500 k x = 0.313 y = 0.329
5500 k x = 0.332 y = 0.347
Physical Specifications
Dimensions : 456x476x437mm(including base)
456x416x437mm(excluding base)
weight : 23.5 Kg
Power supply : 90 - 264 VAC, 50/60HZ
Operating condition
Temperature : 0 C - 35 C
Relative Humidety : 10%-90%
Storage condition
Temperature : - 25 C - 60 C
Relative Humidity :5%-95%
o
o
o
OO
OO
109P2 GS3 CM25
9Go to cover page
Forward
Back

4
109P2 GS3 CM25
Go to cover page
Forward
Back
Front View and Back View
Front View
Front View
Power button switches your monitor on.
OK button which when pressed will take you to
the OSD controls
Contrast hotkey. When the UP arrow is pressed,
the adjustment controls for the CONTRAST will
show up.
UP and DOWN buttons are used when adjusting
the OSD of your monitor
Brightness hotkey. When both the LEFT and
RIGHT arrows are pressed at the same time,
then the adjustment controls for BRIGHTNESS
will show up.
LEFT and RIGHT buttons, like the UP and
DOWN buttons, are also used in adjusting the
OSD of your monitor.
By pressing both the UP and OK buttons, you
can easily access the Input Signals A and/or B.
1. D-Sub Port - Attach the D-Sub connector that comes with your
monitor here. Other end connects to your PC.
2. Power in - Attach power cable here.
3. USB Port - Attach your USB Upstream cable here. Connect the
other end to your USB hub or your PC's USB connector.
4. BNC Connectors - Attach the connectors here to get the best video
performance from your monitor

5
109PB2 GS3 CM25
Go to cover page
Forward
Back
OSD Adjustment
The OSD Tree
On the front controls of your monitor, once you press the button,
the OSD Main Controls window will pop up and you can now start
making adjustment to your monitor's various features. Use the or
the keys to make your adjustments within.
Brightness
1. Press the or button on the monitor. The BRIGHTNESS
window appears.
To adjust your screen's brightness, follow the steps below. Brightness is
the overall intensity of the light coming from the screen. A 50%
brightness is recommended.
Contrast
1. Press the or button on the monitor. The BRIGHTNESS
window appears.
To adjust your screen's contrast, follow the steps below. Contrast is the
difference between the light and dark areas on the screen. A 100%
contrast is recommended.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
2. Press the or button to adjust the brightness.
3. When the brightness is adjusted to the level desired, stop pressing
the or button and after three seconds the BRIGHTNESS
window will disappear with the new adjustment saved.
Below is an overall view of the structure of the OSD. You can use this as
reference when you want to later on work your way around the different
adjustments.

6
109P2 GS3 CM25
Go to cover page
Forward
Back
OSD Lock Function & Service Mode
To unlock (enable) OSD function:
- Press OSD button " " for over 10 seconds again to unlock the
OSD function.
Release it, then OSD comes on the screen as below.
To lock (disable) OSD function:
- Press OSD button " " for over 15 seconds to lock the OSD function.
Release it, then OSD comes on the screen as below.
ATTENTION
CONTROL MENU IS LOCKED
Disable/Enable all the WARNING SIGNAL
NO SIGNAL INPUT
To enable all the WARNING SIGNAL :
- After disconnect the Interface cable of the monitor, then Monitor is
powered ON.
- If it is successful, the signal " " comes on the screen
again later.
Access Service mode (burn in mode) :
Access Service Mode & Burn in mode
Firstly, get into Factory Adjustment Mode.
Push LEFT & RIGHT buttons at the same time for
over 15 seconds and release them.
The factory message appears at the bottom of the
main OSD menu. (for example : 109P V3.08 000601;
00105 is M.T.B.F. in HOUR unit)
SERVICE MODE
SERIAL NO: TY 123456
HOURS : 00021
FACTORY VER 1.01 990706
109P V3.08 000601
00105
NO SIGNAL INPUT
To disable all the WARNING SIGNAL :
- Disconnect the Interface cable of the monitor (Monitor is ON.).
- Press OSD button " " for over 15 seconds to disable all the
WARNING SIGNAL. Then release the "OSD" button.
- If it is successful, then the signal " "disappeared to
enter power saving-off mode.
-Disconnect the Interface cable of the monitor.
- Push LEFT & RIGHT buttons at the same time, then power
ON.
- If it is successful, the signal " "
comes on the screen later.
(Background is white.).
- Reconnect the interface cable to PC, then the "burn in MODE"
Disappear.
Exit "burn in MODE" :

7
109P2 GS3 CM25
Warning and Notes
Fig.1
V
Warnings
1
2
0V
3 ESD
4
5
6
7
8
9
10.
11.
. Safety regulations require that the unit should be returned
in its original condition and that components identical to
the original components are used. The safety components
are indicated by the symbol .
. In order to prevent damage to ICs and transistors, all
high-voltage flash-overs must be avoided. In order to
prevent damage to the picture tube, the method shown
in Fig. 1 should be used to discharge the picture tube.
Use a high-voltage probe and a multimeter (position DC-V).
Discharge until the meter reading is (after approximately
30 seconds).
.
All ICs and many other semiconductors are sensitive to
electrostatic discharges (ESD). Careless handling during
repair can drastically shorten their life. Make sure that
during repair you are connected by a pulse band with
resistance to the same potential as the ground of the unit.
Keep components and tools also at this same potential.
. When repairing a unit, always connect it to the AC Power
voltage via an isolating transformer.
. Be careful when taking measurements in the high-voltage
section and on the picture tube panel.
. It is recommended that saferty goggles be worn when
replacing the picture tube.
. When making adjustments,use plastic rather than metal tools.
This will prevent any short-circuit or the danger of a
circuit becoming unstable.
. Never replace modules or other components while the
unit is switched on.
. Together with the defleciton unit, the picture tube is used
as an integrated unit. Adjustment of this unit during repair
is not recommended.
After repair, the wiring should be fastened in place with
the cable clamps.
All units that are returned for service or repair must pass
the original manufactures safety tests.
Notes
. The direct voltages and waveforms are average voltages.
They have been measured using the Service test software
and under the following conditions :
- Mode : 640 * 480 (31.5kHz / 60Hz)
- Signal pattern : grey scale
- Adjust brightness and contrast control for the
mechanical mid-position (click position)
. The picture tube panel has printed spark gaps.
Each spark gap is connected between an electrode of the
picture tube and the Aquadag coating.
. The semiconductors indicated in the circuit diagram(s)
and in the parts lists are completely interchangeable per
position with the semiconductors in the unit, irrespective
of the type indication on these semiconductors.
1
2
3
9Go to cover page
Forward
Back

8109P2 GS3 CM25 DDC DATA
* ***********************************
EDID data for Mitsubishi CRT
*************************************
0:00 1: ff 2:ff 3:ff 4:ff 5:ff 6:ff 7:00
8: 41 9:0c 10:05 11:00 12:40 13:e2 14:01 15:00
16: 22 17:0a 18:01 19:02 20:6c 21:25 22:1b 23:a7
24: e9 25:7a 26:68 27:9f 28:56 29:47 30:99 31:26
32: 12 33:48 34:4c 35:fd 36:ff 37:80 38:d1 39:40
40: c1 41:40 42:a9 43:4f 44:81 45:99 46:81 47:80
48: 61 49:59 50:45 51:59 52:31 53:59 54:a6 55:59
56: 40 57:30 58:62 59:b0 60:32 61:40 62:40 63:c0
64: 13 65:00 66:63 67:09 68:11 69:00 70:00 71:18
72: 00 73:00 74:00 75:ff 76:00 77:20 78:54 79:59
80: 20 81:20 82:31 83:32 84:33 85:34 86:35 87:37
88: 0a 89:20 90:00 91:00 92:00 93:fc 94:00 95: 50
96: 48 97:49 98:4c 99:49 100:50 101:53 102:20 103:31
104: 30 105:39 106:50 107:32 108:00 109:00 110:00 111: fd
112: 00 113:32 114:a0 115:1e 116:6f 117:1a 118:00 119:0a
120: 20 121:20 122:20 123:20 124:20 125:20 126:00 127:8b
************************************************************
MITSUBISHI GS3.chk
************************************************************
Vendor/Product Identification
ID Manufacturer Name : PHL
ID Product Code : 0005(HEX.)
ID Serial Number : 123456(DEC.)
Week of Manufacture : 34
Year of Manufacture : 2000
EDID Version, Revision
Version : 1
Revision : 2
Basic Display Parameters/Features
Video Input Definition : Analog Video Input
0.700V/0.000V (0.70Vpp)
without Blank-to-Black Setup
Separate Sync
Composite Sync
without Sync on Green
no Serration required
Maximum H Image Size : 36 cm
Maximum V Image Size : 27 cm
Display Transfer Characteristic: 2.67
(gamma)
Feature Support (DPMS) : Standby
Suspend
Active Off
Display Type : RGB color display
Color Characteristics
Red X coordinate : 0.622
Red Y coordinate : 0.339
Green X coordinate : 0.279
Green Y coordinate : 0.6
Blue X coordinate : 0.149
Blue Y coordinate : 0.072
White X coordinate : 0.283
White Y coordinate : 0.297
Established Timings
Established Timings I : 720 x 400 @70Hz (VGA,IBM)
640 x 480 @60Hz (VGA,IBM)
640 x 480 @67Hz (Apple,MacII)
Established timings II : 800 x 600 @72Hz (VESA)
1024 x 768 @75Hz (VESA)
1280 x 1024 @75Hz (VESA)
Manufacturer's timings :
Standard Timing Identification #1
Horizontal active pixels : 1920
Aspect Ratio : 4:3
Refresh Rate : 60
Standard Timing Identification #2
Horizontal active pixels : 1792
Aspect Ratio : 4:3
Refresh Rate : 60
Standard Timing Identification #3
Horizontal active pixels : 1600
Aspect Ratio : 4:3
Refresh Rate : 75
Standard Timing Identification #4
Horizontal active pixels : 1280
Aspect Ratio : 5:4
Refresh Rate : 85
720 x 400 @88Hz (XGA2,IBM)
640 x 480 @72Hz (VESA)
640 x 480 @75Hz (VESA)
800 x 600 @60Hz (VESA)
800 x 600 @75Hz (VESA)
832 x 624 @75Hz (Mac II)
1024 x 768 @87Hz ( IBM)
1024 x 768 @60Hz (VESA)
1024 x 768 @70Hz (VESA)
1152 x 870 @75Hz (Mac II)
Standard Timing Identification #5
Horizontal active pixels : 1280
Aspect Ratio : 5:4
Refresh Rate : 60
Standard Timing Identification #6
Horizontal active pixels : 1024
Aspect Ratio : 4:3
Refresh Rate : 85
Detailed Timing #1
Pixel Clock (MHz) : 229.5
H Active (pixels) : 1600
H Blanking (pixels) : 560
V Active (lines) : 1200
V Blanking (lines) : 50
H Sync Offset (F Porch) (pixels): 64
H Sync Pulse Width (pixels) : 192
V Sync Offset (F Porch) (lines): 1
V Sync Pulse Width (lines) : 3
H Image Size (mm) : 355
V Image Size (mm) : 265
H Border (pixels) : 0
V Border (lines) : 0
Flags : Non-interlaced
Normal Display, No stereo
Digital Seperate Sync
Positive V Sync
Positive H Sync
Monitor Descriptor #2
Serial Number : TY 123456
Monitor Descriptor #3
Monitor Name : Philips 109P2
Monitor Descriptor #4
Min. Vt rate Hz : 50
Max. Vt rate Hz : 160
Min. Horiz. rate kHz : 30
Min. Horiz. rate kHz : 111
Max. Supported Pixel : 260
Extension Flag : 0
Check sum : 8B(hex)
9Go to cover page
Forward
Back

9
109P2 GS3 CM25
DDC Instructions
Additional information :
There are two chips (IC) to store the serial number of monitor
as below.
DDC IC (with EDID data)
OSD IC (EEPROM)
To write the serial number of monitor to DDC IC and OSD IC
simultaneously.
Please follow the indications as below.
- Access the factory mode of monitor.
- Execute DDCV2A F0.EXE
- Follow DDC instructions to write serial number to DDC IC and OSD
IC.
- Turn off monitor (leave factory mode).
- Press OSD button, select MONITOR STATUS, verify the updated
serial number of monitor.
DDC Instructions
Additional information about DDC (Display Data Channel)
may be obtained from Video Electronics Standards
Association (VESA).
Extended Display Identification (EDID) information may be
also be obtained from VESA.
Pin assignment
The 15-pin D-sub connector (male) of the signal cable (3 rows)
for DDC feature :
Pin No. Assignment Pin No. Assignment
1 Red video input 9 No pin
2 Green video input 10 Logic ground
3 Blue video input 11 Connected to pin 10
4 Connected to pin 10 12 Serial data line
(SDA)
5 Ground 13 H.sync/H+V
6 Red video ground 14 V. sync (VCLK for
7 Green video ground DDC)
8 Blue video ground 15 Data clock line(SCL)
5
10
15
1
6
11
This [DDC Module (DDC cable)= 4822 320 12004(=4822 724 27550)]
and
[DDC V2(DDCV2A .EXE) software(3.5" disk)=3138 106 10065 ]
are used for "BU Monitor - Chungli product range" which
incorporates a DDC1/DDC2B function that allows
bi-directional communication between the monitor and
PC system for optimal video configuration.
[January 31 2000, Revision 3.3] ,which upgrades the software and
service information(4822 727 21027 & 4822 727 21038) , is fully
compatible with previous one (DDCV2A F0.EXE).
1. General
In case the DDC data memory IC, replaced due to a defect the
data contents of this IC have to be re- programmed via a PC.
In case of replacement of the video (or deflection) board it is
advised to re-soldered DDC IC from the old board onto the new
board, in this case the IC dose not need to be re-programmed.
2. DDCV2A.EXE can be used for :
EDID Structure Version/Revision
Version : 1
Revision : 0 (text file)
and
Version : 1
Revision : 2 (.hex file)
DDC data re-programming
(Rear of the monitor)
Connection
Video cable
To video card
To printer port (LTP1)
To access factory mode:
-Turn off monitor (don't turn off PC)
- Hold " " and " " simultaneously on the front control panel,
then press " ", wait till the OSD menu with characters "
factory mode (below OSD menu)" come on the screen of monitor
as shown in Fig. 1 .
- If OSD menu disappears on the screen of monitor, press " "
again (anytime), then the OSD menu comes on the screen again.
- using " , " : to select OSD menu.
" " : to increase or decrease the setting.
- Using " " to confirm the selection.
* After alignment of factory mode, turn off monitor (if you do not turn
off monitor, the OSD menu is always at the factory mode), then turn
on monitor again (at this moment, the OSD menu goes back to
user mode).
To leave factory mode
,
Fig 1
00195
109P V3.08 000601
9Go to cover page
Forward
Back

10 DDC Instructions (Continued)
How to write DDC hex files to Monitor
Menu Configuration:










Use arrow keys to highlight "Options" under the Setup menu,
press "Enter"
Tab down to ID Serial Number, use down arrow key to place
the asterisk (*) beside "store in DEC with LSB first". Press
"control/enter" to save.
(Ensure the top asterisk (*) is beside in store in HEX with LSB
first.)
Use arrow keys to highlight "Load EDID" under the file menu,
press "Enter".
Use arrow keys to highlight "PHILIPS\", Press "Enter".
Use arrow keys to highlight "the model list under subdirect",
press "Enter".
Use arrow keys to highlight "Write EDID to EEPROM" under
the R/W menu, press "Enter".
Use arrow keys to highlight "Read from EEPROM" under the
R/W menu, press "Enter".
Use arrow keys to highlight "Edit EDID Code" under the R/W
menu, press "Enter".
Verify the ID Serial number on the screen matches the serial
number of the unit.
Verify EDID Structure Version is "Version :2, Revision :1
Press "ESC"
Use arrow keys to highlight "Quit", Press "Enter".
File R/W Setup Quit
Load EDID Write EDID to EEPROM Options
Load txt file (V1.0) Read From EEPROM Barcode format
Save EDID Edit EDID Code
Save txt File Auto Scan
Convert EDID Code
Os shell
Exit
11
12
109P2 GS3 CM25
DDC Reprogramming Instructions (for
PHILIPS models)
System Requirements
Menu Configuration:
General :
DDC Module (DDC cable), P/N = 4822 320 12004
An Intel 386 (or above) PC or compatible
DOS 6.0 or above
DDCV2A.EXE software
Connect DDC Cable between PC and Monitor.
Turn on Monitor and PC.
Access Factory Mode of monitor.
Verify Factory Mode by OSD function of monitor.
Insert diskette in Drive a: Select Run "DDCV2A F0(Zero).EXE"
or Win. (hit the space bar once )
Verify the data and version of DDC application software.
It should be : January 31 2000
Revision 3.3
Procedure
under
DOS
Press "Enter" at the introduction screen
00MITS.HEX select for 109P20/00(MITS CRT)
File R/W Setup Quit
Load EDID Write EDID to EEPROM Options
Load txt file (V1.0) Read From EEPROM Barcode format
Save EDID Edit EDID Code
Save txt File Auto Scan
Convert EDID Code
Os shell
Exit
1.How to change drive
How to select .HEX files for different Model numbers
Use arrow keys to highlight "Options" under the Setup
menu, press "Enter".
Press "F2", then press "ESC", fill in "A" or "C".
[(If your .HEX files for different Model numbers in drive "A",
then fill in "A").,
(If your .HEX files for different Model numbers in drive "C",
then fill in "C").
Normally, to read DDC data from EEPROM of Monitor is
enough.]
Press "Enter", then press "ESC"
Use arrow keys to highlight "Load EDID" under the File
menu, press "Enter"
Bring up PHILIPS\ press "Enter"
Bring up ..\
109P2 GSIII select, press "Enter"
Bring up ..\ at this highlight area, press
"Enter", then go back to last
screen






ß

2.
example:
ß
9Go to cover page
Forward
Back