Philips MB4010T001 User manual

E
N
1
This "exclamation point" calls attention to a feature for which
you should read the enclosed literature carefully to prevent operating
and maintenance problems.
This "bolt of lightning" indicates that uninsulated material
within your unit may cause an electrical shock. For the safety
of everyone, do not remove product covering.
MB4010T001
AutoScan Color Monitor
CAUTION
ATTENTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER(OR BACK)
NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
For Customer Use:
Enter below the Serial No. which is located on the
back of the cabinet. Retain this information for
future reference.
Model No. MB4010T001
Serial No.
English Operating Instructions...... 2 - 13
Français Mode d'emploi ……………14 - 25
Appendix
English Declaration FCC ... A1
Information for Users in the U.S. ... A3
Warranty ... A5
Deutsch Hinweis / GS ... A4
Achtung ... A6
Français Declaration FCC ... A2

E
N
2
Introduction
The colour monitor displays sharp and brilliant images of text and
graphics with a maximum resolution up to 1024x768 pixels. It is optimal
for Windows, spread sheets, and any other application.
This monitor automatically scans horizontal frequencies from 30KHz to
54KHz, and vertical frequencies from 50Hz to 110Hz. With
microprocessor based digital controlled circuit, the monitor can
automatically adjust itself to the video card’s scanning frequency and
displays an image with precise parameters you desire. The wide range
of scanning frequency supports variety of operating platforms, such as
IBM PC and compatibles, including Intel based platforms such as 386,
486, Pentium and Pentium Pro.
Feature Highlights
•Global Styling demonstrates a soft & smart image.
•Digital Control feature provides user-friendliness and ease-of-use
when operating the monitor.
•Anti-Glare and Anti-Static screen coating eliminate any bad effects
caused by the screen surface such as reflection of the room lights
and dust attraction.
•85Hz refresh rate:
The maximum display resolution is 1024 x 768 pixels non-interlaced
mode. The recommanded optimum resolution up to 800 x 600 pixels
non-interlaced by maximum 85Hz refresh rate.
•Green Design including automatic power saving function (NUTEK)
and low emission MPRII compliance shows our commitment in
environmental care.
•DDC1/DDC2B allows communication between the monitor and PC
system for optimal video configuration.

E
N
3
Note: If you experienced your monitor display is changing from color
to mono, it's possible that you are using a non-VESA-DDC-standard
video card. Please consult with your local Philips dealer for more
information.
As an Energy Star Partner, MAGNAVOX, has determined that this
product meets the Energy Star guidelines for energy efficiency.
IBM, IBM PC and Power PC are registered trademarks of International
Business Machines Corporation.

E
N
4
Safety precautions and maintenance
◆Disconnect the monitor from the mains supply if the monitor is not
to be used for an extended period of time.
◆Do not attempt to remove the back cover, as you will be exposed to
a shock hazard. The back cover should only be removed by qualified
service personnel.
◆Do not place objects on top of the monitor cabinet, which could fall
into vents or which could cover them and prevent proper cooling of
the monitor’s electronic devices.
Do not expose the monitor to rain or excessive moisture to avoid the
risk of shock or permanent damage to the set.
◆Do not use alcohol or ammonia based liquid to clean the monitor. If
necessary, clean with a slightly damp cloth. Disconnect the monitor
from the mains supply before cleaning.
◆Consult a service technician if the monitor does not operate normally
when operating instructions of this manual are followed.
Package
Your package includes the following items:
•The monitor
•Pedestal
•Power cord
•Interface cable (flying-in)
◆
End of life disposal
Your new set contains materials which can be recycled and reused.
Specialized companies can recycle your product to increase the amount
of reusable materials and to minimize the amount of materials to be
disposed of.
Please inform yourself on local regulations on disposal of your old set.

E
N
5
Installation
Important: Please refer to the user’s manuals of your computer and
video adapter to make sure these equipments are properly installed
and configured before installing the monitor.
Positioning / Ventilation
◆Avoid exposing the monitor to direct sunlight, stoves or any other
heat sources.
◆To prevent overheating, make sure that the ventilation openings of
the monitor are not covered.
◆Keep moisture and dust away.
◆Keep away from any magnetic objects, such as speakers, electric
motors, transformers, ...etc.
◆When positioning this monitor, make sure that the mains plug and
socket are easily accessible.
Pedestal
With the built-in pedestal you can tilt and / or swivel the monitor for a
most comfortable viewing angle.
To fit the pedestal, refer to the illustration on the inside back-cover of
this manual.

E
N
6
Connection
Intel Based platform: 386, 486, Pentium, or other compatibles:
•Connect the monitor to the computer using the supplied interface
cables.
Important: Please make sure the AC power to your computer is
“OFF”before connecting or disconnecting any display peripheral.
Failure to do so may cause serious personal injury as well as
permanent damage to your computer equipments.
1) IBM PC connection
2) Mains connection
Monitor rear view
1
2
VIDEO IN
VIDEO IN

E
N
7
Connection to the mains
(Rear of the monitor)
(Mains cord)
Connecting to the mains
This monitor is set to operate at a mains supply of 100-240 volts AC .
If the mains voltage in your home is not between this, consult your
dealer.
Connect one end of the mains cord to the mains socket at the rear of
monitor, and the other end to the mains supply.
The monitor will be operating in power saving mode if you switch on
your monitor without signal input from PC. (Please refer to Power
Management Signalling instruction.)
VIDEO IN

E
N
8
Front Control locations and functions
POWER.
Press this knob, the green LED lights and the power is ON.
Press this knob again, the green LED disappears and the power
is OFF.
CONTRAST
Used to adjust the picture contrast level.
BRIGHTNESS
Used to adjust the overall screen brightness as a compensation
for ambient light.
"+" or "-"
Press "+" or "-" to adjust the selected function.
For an optimized adjustment of the picture following controls are
available at the front.

E
N
9
The function pads:
H-Shift : to adjust the horizontal position of the image.
H-Size : to adjust the horizontal amplitude of the image.
V-Shift : to adjust the vertical position of the image.
V-Size : to adjust the vertical amplitude of the image.
SHIFT key
To select the level of function.
"Shift" LED off - Control is on first level
"Shift" LED on - Control is on second level
Second level of the function pads:
Trapezoid : to correct the trapezoid distortion of the
image.
Pincushion : to correct the barrel distortion of the image
Recall : to recall original factory preset mode
Remarks:
1. When pressing any function pad, the "Shift" LED will flash
once to indicate the function has been selected.
2. Once the limit of the adjustable range has been reached,
the shift LED will flash continuously.

E
N
10
(A) User mode: (15 modes)
The set will save the user's setting parameters automatically.
After 10 seconds of key-pad inactivity, the LED will flash twice to
indicate the parameters being saved.
Adjustment
The monitor is pre-set with 8 modes for optimal display size and centering
as indicated in the following table:
Resolution Horizontal Vertical
Mode (dots x lines) Freq.(KHz) Freq.(Hz) Remark
VGA 640 x 350 31.5 70 Non-interlaced
VGA 640 x 400 31.5 70 Non-interlaced
VGA 640 x 480 31.5 60 Non-interlaced
VESA/75 640 x 480 37.5 75 Non-interlaced
VESA/60 800 x 600 37.8 60 Non-interlaced
VESA/75 800 x 600 46.9 75 Non-interlaced
VESA/60 1024 x 768 48.3 60 Non-interlaced
VESA/85 800 x 600 53.7 85 Non-interlaced