Philips SoHo 150S4FG User manual

Product Information
Product Features • Technical Specifications • Resolution & Preset Modes •
Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification •
Pin Assignment • Product Views • Physical Function
Product Features
150S4FG / 150S4FB
Embedded Power Supply
z15-inch color LCD monitor with excellent display performance
zUltra slim frame design
zStandard VGA analog input
zEmbedded universal AC power supply
zAUTO adjustment optimizes picture quality
zUser installable bezel for optional protective cover choice
RETURN TO TOP OF THE PAGE
Technical Specifications*
LCD PANEL
• Type TFT LCD
• Screen size 15" visual
• Pixel Pitch 0.297 x 0.297mm (15.0")
• LCD Panel type 1024 x 768 pixels
R.G.B. vertical stripe
Anti-glare polarizer hardness
• Effective viewing area 304.1 x 228.1mm (15.0")
• Display Colors 16.7M colors
SCANNING
• Vertical refresh rate 56Hz-76Hz
• Horizontal frequency 30kHz-61kHz
VIDEO
• Video dot rate 80 MHz
• Input impedance
Exhibit 3
Installstion and Operating instructions

* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
- Video 75 ohm
- Sync 2K ohm
• Input signal levels 700m Vpp
• Sync input signal Separate sync
Composite sync
Sync on Green
• Sync polarities Positive and negative
• Input Frequency XGA Hsync 48- 61 kHz, Vsync 60 - 76 Hz (N.I.)
SVGA Hsync 35- 50 kHz, Vsync 56 - 75 Hz (N.I.)
VGA Hsync 31- 38 kHz, Vsync 60 - 76 Hz (N.I.)
• Video interface Analog (D-Sub)
OPTICAL CHARACTERISTICS
• Contrast ratio 400 (typ.)
• Brightness 250 cd/m2(typ.)
• Peak contrast angle 6 o'clock
• White Chromacity x: 0.283 y: 0.297 (at 9300° K) x: 0.313 y: 0.329 (at 6500°
K)
• Viewing Angle (C/R >5)
Upper >50° (typ.)
Lower >60° (typ.)
Left >75 ° (typ.)
Right >75 ° (typ.)
• Response time <=30ms (typ.)
• Maximum 1024 x 768 at 75Hz
• Recommended 1024 x 768 at 60Hz
14 user definable modes
14 factory preset modes:
H. freq (kHz) Resolution V. freq (Hz)
31.469 640*350 70.086
31.469 720*400 70.087
31.469 640*480 59.940
35.000 640*480 67.000

RETURN TO TOP OF THE PAGE
Automatic Power Saving
If you have VESA DPMS compliance display card or software installed in your PC, the monitor
can automatically reduce its power consumption when not in use. If an input from a keyboard,
mouse or other input device is detected, the monitor will 'wake up' automatically. The following
table shows the power consumption and signaling of this automatic power saving feature:
RETURN TO TOP OF THE PAGE
Physical Specifications
37.861 640*480 72.809
37.500 640*480 75.000
35.156 800*600 56.250
37.879 800*600 60.317
48.077 800*600 72.188
46.875 800*600 75.000
49.700 832*624 75.000
48.363 1024*768 60.004
56.476 1024*768 70.069
60.023 1024*768 75.029
Power Management Definition
VESA Mode Video H-sync V-sync Power
Used LED color
ON Active Yes Yes < 30W Green
Stand-by Blanked No Yes < 1W Amber
Suspend Blanked Yes No < 1W Amber
OFF Blanked No No < 1W Amber
This monitor is ENERGY STAR®compliant. As an ENERGY STAR®Partner, PHILIPS
has determined that this product meets the ENERGY STAR®guidelines for energy
efficiency.
• Dimension (WxHxD) * 343 x 310 x 170 mm (incl. Pedestal)
• Weight * 3.7 kg

* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Pin Assignment
The 15-pin D-sub connector (male) of the signal cable:
RETURN TO TOP OF THE PAGE
• Tilt (Forward / Backward) - 5° / 25°
• Power supply 100 — 240 VAC, 50/60 Hz
• Power consumption 23 W (typ.)
• Temperature (operating) 5° C to 40° C
• Relative humidity 20% to 80%
• System MTBF 50K hrs (CCFL 30Khrs)
• Cabinet color 150S4FG: Light Gray
150S4FB: Black
Pin
No. Assignment
Pin
No. Assignment
1Red video input 9DDC +5V
2Green video input 10 Logic ground
3Blue video input 11 Identical output -
connected to pin 10
4Identical output -
connected to pin 10 12 Serial data line (SDA)
5Cable detect 13 H. Sync / H+V
6Red video ground 14 V. Sync
7Green video ground 15 Data clock line (SCL)
8Blue video ground

Product Views
Follow the links to see various views of the monitor and its components.
Front View Product Description
RETURN TO TOP OF THE PAGE
Physical Function
RETURN TO TOP OF THE PAGE
Tilt

Installing your LCD Monitor
Your LCD Monitor : Front View Product Description • Connecting to Your PC •
The Base • Getting Started • Optimizing Performance
Front View Product Description
RETURN TO TOP OF THE PAGE
Optimizing Performance
zFor best performance, ensure that your display settings are set at 1024x768@60Hz
(for14"/15") or 1280x1024, 60Hz (for17"/18").
UP and DOWN buttons are used when adjusting the OSD of your
monitor
LEFT and RIGHT buttons, like the UP and DOWN buttons, are
also used in adjusting the OSD of your monitor.
BRIGHTNESS hotkey. When the UP and DOWN arrow buttons
are pressed, the adjustment controls for the BRIGHTNESS will
show up.
OK button which when pressed will take you to the OSD controls
POWER button switches your monitor on
Automatically adjust the horizontal position, vertical position,
phase and clock setting.

zYou can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the
best performance out of your monitor. This included on this CD. Step-by-step instructions
are provided to guide you through the installtion process. Click on the link to know more
about this program.
More about FP_setup01.exe
RETURN TO TOP OF THE PAGE
Note: You can check the current display settings by pressing the 'OK'
button once. Go into the Product Information. The current display mode is
shown on the item called RESOLUTION.

Connecting to Your PC
Your LCD Monitor : Front View Product Description • Accessory Pack •
Connecting to Your PC • The Base • Getting Started • Optimizing Performance
Accessory Pack
Unpack all the parts.
RETURN TO TOP OF THE PAGE
Connecting to Your PC
Item Description
1) Audio in Cable (Option only available for Multimedia version)
(color lime)
2) Microphone out Cable (Option only available for Multimedia
version)(color pink)
3) Power Cable (socket may differ for different countries)
4) Macintosh Adapter (optional)
5) VGA Signal Cable
6) E-DFU package with Quick Setup Guide, Using Your Monitor
Manual, and CD-ROM.
7) Pivot CD-ROM (optional)

RETURN TO TOP OF THE PAGE
1) Plug the power cord into monitor firmly.
Note: If you use an Apple Macintosh, you
need to connect the special Mac adapter
to one end of the monitor signal cable
2) Connect to PC
(a) Turn off your computer and unplug its power cable.
(b) Connect the monitor signal cable to the video connector on the back
of your computer.
(c) Plug the power cord of your computer and your monitor into a
nearby outlet.
(d) Turn on your computer and monitor. If the monitor displays an
image, installation is complete.

The Base
Your LCD Monitor : Front View Product Description • Accessory Pack •
Connecting to Your PC • Getting Started • Optimizing Performance
Unfold and Fold the Base : Unfold the base • Fold the base
Remove the Base : Remove the base
Unfold and Fold the Base
Unfold the Base
Fold the Base
1) Put monitor face down on
the safe surface
2) Pull up the base
1) Put monitor face
down on the safe
surface