Philips BT4080 User manual

www.philips.com/support
BT4080
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips

1EN
Contents
1 Important 2
Safety 2
2 Your Bluetooth speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Power supply 5
Turn on 5
4 Use Bluetooth devices 6
Connect a device 6
Play from Bluetooth device 7
Control your phone call 7
Disconnect the Bluetooth-enabled device 7
Connect another Bluetooth-enabled
device 7
Reconnect the Bluetooth device 7
5 Other features 8
Listen to an external device 8
Charge your mobile devices 8
Adjust volume 9
6 Product information 10
Specications 10
7 Troubleshooting 11
General 11
About Bluetooth device 11
8 Notice 12

2EN
1 Important
Safety
Warning
• Never remove the casing of this speaker.
• Never lubricate any part of this speaker.
• Never place this speaker on other electrical equipment.
• Keep this speaker away from direct sunlight, naked
amesorheat.
Important safety instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including ampliers) that
produce heat.
i Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
j Only use attachments/accessories
specied by the manufacturer.
k Unplug this apparatus during lightning
storms or when unused for long periods
of time.
l Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
m Battery shall not be exposed to excessive
heat such as sunshine, re or the like.
n Apparatus shall not be exposed to
dripping or splashing.
o Do not place any sources of danger on
the apparatus (e.g. liquid lled objects,
lighted candles).
p Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
Note
• The type plate is located on the bottom of the
apparatus.

3EN
2 Your Bluetooth
speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can
• enjoy audio from your Bluetooth-enabled
devices, or other external audio devices;
and
• charge your mobile devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• Power adapter
• Short user manual
•

4EN
Overview of the speaker
a
• Turn the speaker on or off.
b +/-
• Adjust volume.
c /PAIRING
• Answer or reject an incoming call.
• End the current phone call.
• Enter Bluetooth pairing mode.
d NFC
• Connect a device with NFC feature
through Bluetooth.
e AUDIO IN
• Connect an external audio device.
f CHARGING 5V 1A
• Charge your mobile devices.
g DC IN
• Connect power.
abc
d
e
f
g

5EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Power supply
The Bluetooth speaker can be powered by
either AC mains or built-in battery.
Option 1:AC power
Caution
• Risk of product damage! Make sure that the power
voltage corresponds to the voltage printed on the back
or underside of the speaker.
Connect the power adapter to:
• the DC IN socket on the speaker.
• the wall outlet.
Option 2: Battery power
The speaker can operate on the built-in
rechargeable battery.
Note
• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
• It takes approximately 6 hours to fully charge the
battery.
• When battery is low or under charging, the LED
indicatorashesred.
DC IN
To recharge the built-in battery:
Connect the speaker to AC power supply.
Turn on
Press to turn the speaker on.
» TheLEDindicatorashesblue.
Note
• Ifbatteryislow,theLEDindicatorashesred.
Turn off
Press again to turn the speaker off.
Note
• If the connection with Bluetooth devices or other
external devices is invalid for 15 minutes, the speaker
switches to standby mode automatically for power
saving.

6EN
4 Use Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices and control the
incoming call through Bluetooth.
Connect a device
Note
• Make sure that your Bluetooth device is compatible
with this speaker.
• Before pairing a device with this speaker, read its user
manual for Bluetooth compatibility.
• The speaker can memorize a maximum of four paired
devices.Thefthpaireddevicewillreplacetherstone.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
• Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
Option 1: Connect a device through
NFC
Near Field Communication (NFC) is a
technology that enables short-range wireless
communication between various NFC
compatible devices, such as mobile phones and
IC tags.
If your Bluetooth device supports NFC, you can
connect it with this speaker easily.
1 On your device, enable NFC and
Bluetooth functions (refer to the user
manual of the device).
2 Press on this speaker.
» TheLEDindicatorashesblue.
3 Touch the NFC tag on the top of the
speaker with the NFC area of your
Bluetooth device.
4 On your Bluetooth device, accept the
pairing request with "PHILIPS BT4080".
If necessary, input “0000” as the pairing
password.
5 Follow the on-screen instructions to
complete the pairing and connection.
» After successful connection, the
speaker beeps twice, and the LED
indicator turns solid blue.
Option 2: Connect a device manually
1 Press .
» TheLEDindicatorashesblue.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (see the user manual of
the device).
3 When [Philips BT4080] is displayed on
your device, select it to start pairing and
connection. If necessary, input “0000” as
the pairing password.
» After successful pairing and connection,
the speaker beeps twice, and the LED
indicator turns solid blue.
• Ifyoufailtond[Philips BT4080] for
pairing, press and hold PAIRING for
two seconds to enter pairing mode
rst.
LED indicator Description
Flashing blue Connecting;
Waiting for pairing
Solid blue Connected

7EN
Play from Bluetooth device
Note
• If there is an incoming call on the connected mobile
phone, music play pauses.
After successful Bluetooth connection, play
audio on the Bluetooth device.
» Audio streams from your Bluetooth
device to the speaker.
Control your phone call
After Bluetooth connection, you can control an
incoming call with this speaker.
Button Function
Press to answer an incoming call.
Press and hold for two seconds to
reject an incoming call.
During a call, press to end the current
call.
Note
• Music play pauses when there is an incoming call.
Disconnect the Bluetooth-
enabled device
• Press and hold PAIRING for two seconds;
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
» TheLEDindicatorashes.
Connect another Bluetooth-
enabled device
1 Press and hold PAIRING for two seconds
to disconnect the currently connected
device;
» The speaker enters Bluetooth pairing
mode.
2 Connect another Bluetooth device.
Reconnect the Bluetooth
device
• Next time when you turn on the speaker,
it will reconnect the last connected device
automatically; or
• On your Bluetooth device, select "PHILIPS
BT4080" on your Bluetooth menu to start
connection.

8EN
5 Other features
Listen to an external device
With this speaker, you can also listen to an
external audio device such as an MP3 player.
Note
• Make sure that there is no Bluetooth connection, or
music playback through Bluetooth is paused.
1 Connect an audio input cable (not
supplied) with a 3.5 mm connector on
both ends to
• the AUDIO IN socket on this speaker,
and
• the headphone socket on the external
device.
» The speaker switches to audio-in
mode automatically.
2 Play audio on the external device (refer to
its user manual).
AUDIO IN
Charge your mobile devices
You can charge your mobile devices through
the USB socket.
Note
• The USB socket is for charging only.
1 Connect this speaker to AC power.
2 Connect this speaker to your mobile
device with a USB cable (not supplied).
» Once the device is recognized, the
charging starts.
Adjust volume
During play, press +or -repeatedly to increase
or decrease the volume level.
Tip
• To increase or decrease volume continuously, press and
hold +or -for 2 seconds.
• When the volume reaches the maximum or minimum,
theLEDindicatorashestwice.
CHARGING

9EN
6 Product
information
Note
• Product information is subject to change without prior
notice.
Specications
Amplier
Rated Output Power 2 X 10 W RMS
Frequency Response 80 -16000 Hz, ±3 dB
Signal to Noise Ratio >67 dBA
Audio-in Input 600 mV RMS 20 kohm
Bluetooth
Bluetooth Version V4.0
SupportedProles HFP, A2DP, AVRCP
Bluetooth Frequency
Brand
2.4 GHz ~ 2.48 GHz
Bluetooth Range 10 m (Free space)
Speakers
Speaker Impedance 8 ohm
Speaker Driver 7cm full range
Sensitivity >84dB/m/W ±
3dB/m/W
General information
Power Supply
- AC Power (Power
Adapter)
Brand name: PHILIPS;
Model: AS450-150-
AA250;
Input: 100-240 V~,
50/60 Hz, 1.2 A
Output: 15 V 2.5 A;
- Battery (Built-in) 11.1 V, 1500 mAh
Operation Power
Consumption
12.5 W (with 1A
charging loader)
Eco Standby Power
Consumption
< 0.5 W
Charging current
and voltage
5V, 1A
Dimensions - Main
Unit (W x H x D)
300 x 163 x 96 mm
Weight - Main Unit 1.9 kg

10 EN
7 Troubleshooting
Warning
• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
General
No power
•Make sure that the AC power plug of the
speaker is connected properly.
•Make sure that there is power at the AC
outlet.
•Recharge the built-in battery.
No sound or poor sound
•Adjust volume on the product.
•Adjust volume on the connected device.
No response from the speaker
•Restart the speaker.
The LED indicator ashes blue for 5 times,
and the speaker has no response when
pressing any key.
•The speaker is in DEMO mode. Press and
hold for 15 seconds to exit this mode.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
Cannot connect with the device.
•The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
•This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.
The paired device connects and disconnects
constantly.
•The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
•For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature.This does not indicate
any malfunction of this product.

11EN
8 Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Notice for the USA and Canada
This device complies with Part 15 of the FCC
Rules and license-exempt RSS standard of
Industry Canada. Operation is subject to the
following two conditions:
1 this device may not cause harmful
interference, and
2 this device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:
• Relocate the receiving antenna.
• Increase the separation between
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
RF Radiation Exposure Statement: This
equipment complies with FCC’s and IC’s RF
radiation exposure limits set forth for an
uncontrolled environment.The antenna(s)
used for this transmitter must be installed and
operated to provide a separation distance of
at least 20 cm from all persons and must not
be collocated or operating in conjunction with
any other antenna or transmitter. Installers must
ensure that 20cm separation distance will be
maintained between the device (excluding its
handset) and users.
CAN ICES-3(B)/NMB-3(B)
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This product may contain lead and mercury.
Disposal of these materials may be regulated
due to environmental considerations. For
disposal or recycling information, please contact
your local authorities or visit www.recycle.
philips.com.
This product contains non-removable batteries:
• Do not incinerate. Batteries may explode if
overheated.
• For disposal or recycling information,
please contact your local authorities or visit
www.recycle.philips.com.
Caution
• Removal of the built-in battery invalidates the warranty
and may destroy the product.
Always bring your product to a professional to
remove the built-in battery.

12 EN
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
The Bluetooth word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
is under license. Other trademarks and trade
names are those of their respective owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.

13EN

Specications are subject to change without notice.
2015 © Gibson Innovations Limited.All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license from Koninklijke Philips N.V.
BT4080_37_UM_V2.0