Philips BT6600 User manual

www.philips.com/support
Always there to help you
Register your product and get support at
BT6600
User manual
Question?
Contact
Philips

1EN
Contents
1 Important 2
2 Your Bluetooth speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Power supply 5
Turn on/off 6
Adjust volume 6
4 Use Bluetooth devices 7
Connect a device 7
Connect three Bluetooth devices
simultaneously 8
Play from Bluetooth device 8
Control your phone call 8
5 Listen to an external device 9
6 Charge your device 10
7 Product information 11
Specications 11
8 Troubleshooting 12
General 12
About Bluetooth device 12
9 Notice 13
Compliance 13
Care of the environment 13
Trademark notice 14

2EN
1 Important
Warning
• Never remove the casing of this speaker.
• Never place this speaker on other electrical equipment.
• Keep this speaker away from direct sunlight, naked
amesorheat.
• Make sure that you always have easy access to the
power cord, plug, or adaptor to disconnect the speaker
from the power.
• Make sure that there is enough free space
around the speaker for ventilation.
• After use under humid circumstance,
immediately clean the product with a soft
dry cloth.
• The battery shall not be exposed to
excessiveheatsuchassunshine,reorthe
like.
• The adapter shall not be exposed to
dripping or splashing.
• Noobjectslledwithliquidsshallbe
placed on the adapter.
• Use only power supplies listed in the user
manual.
• Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.

3EN
2 Your Bluetooth
speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
This speaker has passed splash-proof test
(IPX4) and can be used near water.
With this speaker, you can enjoy audio from
Bluetooth-enabled devices or other external
devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• USB adapter head
• The charging base
• Short user manual
• Safetyandnoticeleaet
Short User Manual
www.philips.com/welcome
Always there to help you
Register your product and get support at
Question?
Contact
Philips

4EN
Overview of the speaker
a / /MULTIPAIR
• Enter Bluetooth pairing mode.
• Disconnect Bluetooth connection.
• Answer or reject an incoming call.
• End the current phone call.
• Transfer the call to your mobile device.
b NFC
• Connect a NFC compatible device
through Bluetooth.
c Bluetooth indicator
d Volume knob ( )
• Adjust volume.
• Turn the speaker on or off.
e DC IN socket
f AUDIO IN
• Connect an external audio device.
g socket
• Charge your mobile device.
c
d
e
e
f
g
a
b

5EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Power supply
Either AC power or battery can be used as
power supply of this product.
Option 1: Battery power
The speaker can operate on the built-in
rechargeable battery.
Note
• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
• It takes approximately three hours to fully charge the
battery.
• TheredLEDindicatorasheswhenthebatteryislow.
To recharge the built-in battery:
• Dock the speaker into the charging base,
then connect the speaker to the AC power
by using the supplied adaptor; or
• Connect the speaker to AC power by
using the supplied adaptor directly; or
• Connect the USB cable between
• the socket on the speaker, and
• a USB socket on a computer.
When the speaker is off, the LED indicator is
shown as below when it is under charging.
LED indicator Battery status
Solid red Under charging
Off Fully charged
Option 2:AC power
Caution
• Risk of product damage! Make sure that the power
voltage corresponds to the voltage printed on the back
or underside of the speaker.
• Risk of electric shock! When you unplug the AC
adapter, always pull the plug from the socket. Never
pull the cord.
1 Connect the adapter to:
• the socket on the speaker.
• the power outlet.

6EN
2 Connect the USB cable to the DC IN
socket on the speaker or on the charging
base.
Turn on/off
• To turn the speaker on or off, rotate the
knob clockwise or anticlockwise until you
hear a click.
» When the speaker is turned on, the
blueLEDindicatorashes.
» When the speaker is turned off, the
blue LED indicator lights off.
OFF
ON
Note
• Ifbatteryislow,theredLEDindicatorashesred.
Switch to standby mode
• The speaker switches to standby mode in
the following situations:
• The connection with Bluetooth
device or other device is invalid for 15
minutes; or
• Music playback is stopped for 15
minutes.
Note
• When the speaker is in standby mode, the LED
indicatorashesblue.
• To wake up the speaker from standby mode, press
MULTIPAIR or tap the NFC tag on the top of the
speaker with your Bluetooth device.
Adjust volume
• During play, rotate the knob to increase or
decrease volume.

7EN
4 Use Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices and control the
incoming call through Bluetooth.
Connect a device
Note
• The speaker can memorize a maximum of three paired
devices.Thefourthpaireddevicewillreplacetherst
one.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
• Make sure that no audio input cable is connected to
the AUDIO IN socket.
Option 1: Connect a device through
NFC
Near Field Communication (NFC) is a
technology that enables short-range wireless
communication between various NFC
compatible devices, such as mobile phones and
IC tags.
If your Bluetooth device supports NFC, you can
connect it with this speaker easily.
1 Enable NFC on your Bluetooth device
(refer to its user manual).
2 Turn on the speaker.
» TheblueLEDindicatorashes.
3 Tap the NFC tag on the top of the speaker
with the NFC area of your Bluetooth
device.
4 Follow the on-screen instructions to
complete the pairing and connection.
» After successful connection, the
speaker beeps twice, and the LED
indicator turns solid blue.
• The speaker doesn't beep during
music playback, only the LED indicator
ashesblue.
Option 2: Connect a device manually
Note
• The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
1 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (see the user manual of
the device).
2 Turn on the speaker.
» TheblueLEDindicatorashes.
3 Select [Philips BT6600] displayed on your
device for pairing. If necessary, input “0000”
as the pairing password.
» After successful connection, the
speaker beeps twice, and the LED
indicator turns solid blue.
• The speaker doesn't beep during
music playback, only the LED indicator
ashesblue.
LED indicator Description
Flashing blue quickly (at
2Hz)
Waiting for
pairing
Flashing blue slowly(at 1Hz) Connecting
Solid blue Connected

8EN
Connect three Bluetooth
devices simultaneously
The speaker can connect to three Bluetooth
devices at the same time.
• If the speaker is connected to one device,
press and hold MULTIPAIR for two
seconds.
» The speaker enters pairing mode,
and gets ready to pair with a new
Bluetooth device.
» The previous device is still connected
to the speaker
• If the speaker is connected to three
devices, press and hold MULTIPAIR for
two seconds.
» The speaker disconnects the earliest
device which is not playing music , and
gets ready to pair with another device.
Play from Bluetooth device
Note
• If there is an incoming call on the connected mobile
phone, music play pauses.
After successful Bluetooth connection, play
audio on the Bluetooth device.
2 sec.
» Audio streams from your Bluetooth
device to the speaker.
• If more than one device is connected with
the speaker, play music from any of the
connected devices, the music playback
through other device is paused.
Control your phone call
After Bluetooth connection, you can control an
incoming call with this speaker.
Button Function
/ Press to answer an incoming call.
Press and hold for three seconds to
reject an incoming call.
During a call, press to end the current
call.
During a call, press and hold for three
seconds to transfer the call to your
mobile device.