Philips 320WN6 User manual

Page 1 of 1320wn6

Product Information
Product Features • Technical Specifications • Resolution & Preset
Modes • Philips Pixel Defect Policy • Automatic Power Saving •
Physical Specification • Pin Assignment • Product Views
Product Features
320WN6
zLess management effort for maximum productivity
{Multiple displays form a daisy chain to show uniform
{Monitor is network controllable for remote management
{Input connectors: CVBS, S-video, SCART, YPbPr, and RF (TV
input)
zBetter front of screen experience
{Motion adaptive deinterlacing for razor sharp images
{3D comb filter separates color for a razor-sharp image
{WXGA, wide format 1366 x 768 resolution for sharper display
{Adaptive brightness intensifier technology
{Ready to display SDTV, EDTV, and HDTV formats
zGreat convenience
{Zoom function to enable tiled matrix application
{Support hight-bandwidth digital content protection decryption
{Split screen for dual video/PC display
{Picture in picture for public display
* RF(TV input) is only available for 320WN6QS
RETURN TO TOP OF THE PAGE
Technical Specifications*
LCD PANEL
• Type TFT LCD
• Screen size 31.51inch
• Pixel Pitch 0.17 x 0.511 mm
• LCD Panel type 1366 x 768 pixels R.G.B. vertical stripe
Hard coating surface, anti-glare polarizer
• Effective viewing area 697.7 x 392.2 mm
Page 1 of 8Product Information

• Display Colors 8 bits interface (16.7M colors)
PC SCANNING
• Vertical refresh rate 56Hz-75Hz
• Horizontal frequency 30kHz-63kHz
PC VIDEO
• Video dot rate < 85 MHz
• Input impedance
- Video 75 ohm
- Sync 2.2K ohm
• Input signal levels 0.7 Vpp
• Sync input signal Separate sync
• Sync polarities Positive and negative
• Input Frequency
WXGA Hsync 48 kHz, Vsync 60 Hz
(N.I.)
SVGA Hsync 38 kHz, Vsync 60 Hz
(N.I.)
VGA/DVI-D Hsync 31 kHz, Vsync 60 Hz
(N.I.)
• Video interface D-sub, S-Video, TV-RF, SCART
composite, components video, and DVI
AUDIO
• Input level for
PC/SVHS/SCART 500 mV nominal
• Loudspeaker 10W Stereo Audio (10W/channel RMS x2,
200Hz~10kHz, 8 ohm, 10% THD)
OPTICAL CHARACTERISTICS
• Contrast ratio 1200:1(with DCR on)
• Brightness 500 cd/m2(typ.)
• Peak contrast angle 6 o'clock
• White Chromaticity x: 0.283 y: 0.297 (at 9300°K)
x: 0.313 y: 0.329 (at 6500°K)
x: 0.328 y: 0.344 (at 5700°K)
• Viewing Angle (C/R >5) Upper >89° (typ.)
Lower >89° (typ.)
Left >89° (typ.)
Right >89° (typ.)
Page 2 of 8Product Information

* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
• Response time (G to G) 8ms(typ.) 12ms(max.)
sRGB
sRGB is a standard for ensuring correct exchange of colors between different
devices (e.g. digital cameras, monitors, printers, scanners, etc.)
Using a standard unified color space, sRGB will help represent pictures taken
by an sRGB compatible device correctly on your sRGB enabled Philips
monitors. In that way, the colors are calibrated and you can rely on the
correctness of the colors shown on your screen.
Important with the use of sRGB is that the brightness and contrast of your
monitor is fixed to a predefined setting as well as the color gamut. Therefore
it is important to select the sRGB setting in the monitor's OSD.
To do so, at PC mode, open the OSD by pressing the MENU button of your
monitor. Use the down button to go to COLOR SETTINGS and press MENU
again. Then move the down button to go to NORMAL COLOR and press
MENU again.
• Recommended 1360 x 768 at 60Hz
10 factory preset modes:
Resolution Mode H. freq (kHz) V. freq (Hz)
PC
640x350 VGA-1 31.469 70.086
640x480 VGA VESA 60 31.469 59.940
640x480 VGA VESA 75 37.500 75.000
720x400 IBM VGA 3H 31.468 70.087
800x600 SVGA VESA 56 35.156 56.250
800x600 SVGA VESA 60 37.879 60.317
800x600 SVGA VESA 75 46.875 75.000
1280x1024 XGA VESA 60 48.363 60.004
1280x1024 XGA VESA 75 60.023 75.029
1280x768 GTF 60 47.700 60.000
Page 3 of 8Product Information

RETURN TO TOP OF THE PAGE
Automatic Power Saving
If you have VESA DPMS compliance display card or software installed in your
PC, the monitor can automatically reduce its power consumption when not in
use. If an input from a keyboard, mouse or other input device is detected, the
monitor will then 'wake up' automatically. The following table shows the power
consumption and signaling of this automatic power saving feature:
RETURN TO TOP OF THE PAGE
Physical Specifications
1280x768 Wincomm 45.113 56.260
1360x768 VESA 47.700 60.000
Video
720x480 480i 15.734 59.940
720x576 576i 15.625 50.000
720x480 480p 31.470 60.000
720x576 576p 31.250 50.000
1280x720 720p 28.200 50.000
1280x720 720p 33.750 60.000
1920x1080 1080i 37.500 50.000
1920x1080 1080i 45.000 60.000
Power Management Definition
VESA
Mode Video H-sync V- sync Power Used LED color
Active On Yes Yes 100 W (typ.) Blue
Sleep Off No No < 5 W Amber
Switch Off Off - - < 3 W Off
• Dimension (WxHxD) * 1014mm x 517mm x 244mm (incl. Pedestal,
Speakers)
Page 4 of 8Product Information

* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Pin Assignment
1. The digital only connector (DVI-D) contains 24 signal contacts organized in
three rows of eight contacts. Signal pin assignments are listed in the following
table:
794mm x 490mm x 130mm (w/o Pedestal,
Speakers)
• Weight 19.2 kg (incl. Pedestal, Speakers)
• Power supply 100 — 240 VAC, 60 — 50 Hz
• Power consumption PC Mode: 100 W (typ.)
TV Mode: 130 W (typ.)
• Temperature (operating) 5° C to 35° C
• Relative humidity 20% to 80%
• System MTBF 50K hrs (excluding CCFL 40Khrs)
Pin
No. Signal
Assignment
Pin
No. Signal
Assignment
Pin
No. Signal Assignment
1T.M.D.S. Data2- 9T.M.D.S. Data1- 17 T.M.D.S. Data0-
2T.M.D.S.
Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+
3T.M.D.S.
Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield
4No connect 12 No connect 20 No connect
5No connect 13 No connect 21 No connect
6DDC Clock 14 +5V Power 22 T.M.D.S. Clock
Shield
7DDC Data 15 Hot Plug Detect 23 T.M.D.S.
Clock+
Ground (for
Page 5 of 8Product Information

2. The 15-pin D-sub connector (male) of the signal cable:
3. RS232 Connector
D-sub 9-pin male connector for communication with plasma engine or PC.
8No connect 16 +5V) 24 T.M.D.S. Clock-
Pin
No. Assignment Pin No. Assignment
1Red video input 9DDC +5V
2Green video input 10 Cable detect
3Blue video input 11 Identical output,
connected to pin 10
4Ground 12 Serial data line
(SDA)
5NC 13 H. Sync / H+V
6Red video ground 14 V. Sync
7Green video
ground 15 Data clock line (SCL)
8Blue video ground
Pin No. RS-232 (EIA-232-A) Function
3Transmit Data (TD) from DTE to DCE
2Receive Data (RD) from DCE to DTE
7Request to Send (RTS)
8Clear to Send (CTS)
6DCE Ready (DSR)
5Signal Ground (SG)
Page 6 of 8Product Information

4. SCART Connector
1Received Line Signal Detector (DCD)
4DTE Ready (DTR)
9Ring Indicator
Pin
No. Signal Pin No.
1Audio right channel output (0.5 Vrms,
< 1K ohms) 2
2Audio right channel input (0.5 Vrms, >
10K ohms) 1
3Audio left channel output (0.5 Vrms, <
1K ohms) 6
4Audio ground 4
5Blue signal ground 5
6Audio left channel input (0.5 Vrms, >
10K ohms) 3
7Blue signal I/O (0.7 Vp-p, 75 ohms) 7
8Function switching I/O (L: < 2V, H: >
10V, 10K ohms) 8
9Green signal ground 9
10 Intercommunication data line No. 1 10
11 Green signal I/O (0.7 Vp-p, 75 ohms) 11
12 Intercommunication data line No. 2 12
13 Red signal ground 13
14 Blanking signal ground 14
15 Red signal I/O (0.7 Vp-p, 75 ohms) 15
16 Blanking signal I/O (L: < 0.4V, H:
>1.0V, 75 ohms) 16
17 Composite video signal ground 18
18 Blanking signal ground 17
19 Composite video signal output (1 Vp- 20
Page 7 of 8Product Information

RETURN TO TOP OF THE PAGE
Product Views
Follow the links to see various views of the monitor and its components.
Product Description
RETURN TO TOP OF THE PAGE
p, 75 ohms, sync: negative)
20 Composite video signal input (1 Vp-p,
75 ohms, sync: negative) 19
21 Plug shield (common ground) 21
Page 8 of 8Product Information

Installing your LCD Monitor/TV
Product Description • Connecting to Your PC, TV antenna, DVD/VCR etc. •
Getting Started • Optimizing Performance
Product Description
Installing your LCD Monitor/TV
Side View (Left)
Page 1 of 4Installing your LCD Monitor/TV