Philips BDL8470EU User manual

www.philips.com/welcome
BDL8470EU
V1.00
User Manual (English)

BDL8470EU
ii
Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specied in this documentation may result in exposure to
shock, electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your display:
Operation:
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• When turning off the display by detaching the power cord, wait 6 seconds before re-attaching the power cord for normal operation.
• Ensure the use of an approved power cord provided by Philips at all times. If your power cord is missing, please contact your local service center.
• Do not subject the display to severe vibration or high impact conditions during operation.
• Do not knock or drop the display during operation or transportation.
Maintenance:
• To protect your display from possible damage, do not put excessive pressure on the LCD panel.When moving your display, grasp the frame to lift; do
not lift the display by placing your hand or ngers on the LCD panel.
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth.The screen may be wiped with a dry cloth when the power is off. However, never
use organic solvent, such as, alcohol, or ammonia-based liquids to clean your display.
• To avoid the risk of shock or permanent damage to the set, do not expose the display to dust, rain, water or an excessively moist environment.
• If your display becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in your display, turn the power off immediately and disconnect the power cord.Then remove the foreign substance
or water, and send the unit to the maintenance center.
• Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your display and ensure a longer lifetime, we strongly recommend using the display in a location that falls
within the following temperature and humidity ranges.
-Temperature: 0-40°C 32-104°F
-Humidity: 20-80% RH
IMPORTANT: Always activate a moving screen saver program when you leave your display unattended.Always activate a periodic screen refresh
application if the unit will display unchanging static content. Uninterrupted display of still or static images over an extended period may cause “burn in”,
also known as “after-imaging” or “ghost imaging”, on your screen.This is a well-known phenomenon in LCD panel technology. In most cases, the “burned
in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.This is also not covered under the
terms of your warranty.
Service:
• The casing cover should be opened only by qualied service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave your display under direct sunlight.
If your display does not operate normally, having followed the instructions set out in this document, please contact a technician or your
local service center.

BDL8470EU
iii
Read and follow these instructions when connecting and using your display:
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth.The screen many be wiped with a dry cloth when the power is
off. However, never use alcohol, solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.
• The casing cover should be opened only by qualied service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry.To avoid electric shock, do not expose it to rain or excessive moisture.
• When turning off the display by detaching the power cable or DC power cord, wait for 6 seconds before re-attaching the power
cable or DC power cord for normal operation..
• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the
screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen.This is a well-known
phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually
over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not
covered under warranty.
CE Declaration of Conformity
We declare under our responsibility that the product is in conformity with the following standards:
• EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 (Safety requirement of InformationTechnology Equipment).
• EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment).
• EN55024:2010 (Immunity requirement of InformationTechnology Equipment).
• EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission).
• EN61000-3-3:2013 (Limitation ofVoltage Fluctuation and Flicker)
• EN 50581:2012 (Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous
substances)
• 2006/95/EC (LowVoltage Directive).
• 2004/108/EC (EMC Directive).
• 2011/65/EU (RoHS Directive) and is produced by a manufacturing organization on ISO9000 level.
Warning:
This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
appropriate measures.
Federal Communications Commission (FCC) Notice (U.S. Only)
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference is which case the user will be required to correct the interference at his own
expense.
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive moisture.

BDL8470EU
iv
Polish Center for Testing and Certication Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).All equipment that works together (computer,
display, printer, and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value
no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the
equipment and easily accessible.
A protection mark “B” conrms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/
E-06251.
Electric, Magnetic and Electromagnetic Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive
electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal
requirements and to stay well within the EMF standards applicable at the time of producing the products.
3. We are committed to develop, produce and market products that cause no adverse health effects.
4. We conrm that if its products are handled properly for their intended use, they are safe to use according to scientic evidence available today.
5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization
for early integration in its products.

BDL8470EU
v
Information for U.K. only
(A)
(B)
WARNING -THIS APPLIANCE MUST BE EARTHED.
Important:
This apparatus is supplied with an approved moulded 13A plug.To change a fuse in this type of plug
proceed as follows:+
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.
3. Ret the fuse cover.
If the tted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin
plug tted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the
fuse at the distribution board should not be greater than 5A.
NOTE: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted
into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN &YELLOW - “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked
with the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or
coloured BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter “L” or
coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead
- not simply over the three wires.
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRGVED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAANTARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

BDL8470EU
vi
China RoHS
根据中国大陆《电子电气产品有害物质限制使用标识要求》，以下部分列出了本产品中可能包含的有害
物质的名称和含量。
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr 6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
外壳 ○ ○ ○ ○ ○ ○
液晶显示屏/灯管 × × ○ ○ ○ ○
电路板组件*×○ ○ ○ ○ ○
电源适配器 ×○ ○ ○ ○ ○
电源线/连接线 ×○ ○ ○ ○ ○
遥控器 ○ ○ ○ ○ ○ ○
本表格依据SJ/T 11364 的规定编制。
*: 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。
上表中打“×”的部件，应功能需要，部分有害物质含量超出GB/T 26572规定的限量要求，但符合欧盟RoHS法
规要求（属于豁免部分）。
10 環保使用期限
此標識指期限(十年)，電子信息產品中含有的有毒有害物質或元素在正常使用的條件下不會發生外泄或突變
，電子信息產品用戶使用該電子信息產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。
中国能源效率标识
根据中国大陆《能源效率标识管理办法》，本显示器符合以下要求
能源效率（cd/W) >1.05
能效等级 1 级
能效标准 GB 21520-2008
详细有关信息请查阅中国能效标识网： http://www.energylabel.gov.cn/

BDL8470EU
vii
《废弃电器电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品
回收处理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。
娤⌈
㨢᳸$䵥ᵥ⍿Ʋ◦䏝㯹䉭❁ᳫ濕媣ᵥ⍿⊭侻󰵹廞ノ㒞䵽䏳ⴰㄮƲ◦店䢋⾃⁳᳉濕⊭侻斾堿䏦ヵ
⪷ⴰㄮ悅⊔⃅⩜⊭圊䕂㉨㑻Ʋ
End-of-Life Disposal
Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the
amount of reusable materials and to minimize the amount to be disposed of.
Please nd out about the local regulations on how to dispose of your old display from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling
contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and
electronic appliances, this product may not be disposed of with normal household waste.You are responsible for disposal of this
equipment through a designated waste electrical and electronic equipment collection.To determine the locations for dropping off such
waste electrical and electronic, contact your local government ofce, the waste disposal organization that serves your household or the
store at which you purchased the product.
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.mygreenelectronics.com or www.
eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Please dispose of according to all Local, State, and Federal laws.
Restriction on Hazardous Substances statement (India)
This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2
of the Rule.
E-Waste Declaration for India
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling
of waste electrical and electronic equipment .The separate collection and recycling of your waste equipment at the time of disposal
will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environ-ment.
For more information about where you can drop off your waste equipment for recycling in India please visit the below web link.
http://www.india.philips.com/about/sustainability/recycling/index.page

BDL8470EU
viii
Batteries
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There
is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation.
Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall be
separated to collect by local service.
Após o uso, as pilhas
deverão ser entregues ao
estabelecimento comercial ou
e/ou baterias
rede de assistência técnica
autorizada.

BDL8470EU
ix
Table Of Contents
1. Unpacking and Installation.......................................................1
1.1. Unpacking.........................................................................................1
1.2. Package Contents........................................................................1
1.3. Installation Notes.........................................................................1
1.4. Mounting on a Wall....................................................................2
1.4.1. VESA Grid....................................................................2
1.5. Mounting in Portrait Position................................................3
1.5.1. How to use the logo guider for portrait
position...........................................................................3
1.5.2. How to remove the logo.....................................3
2. Parts and Functions...................................................................4
2.1. Control Panel.................................................................................4
2.2. Input/OutputTerminals.............................................................5
2.3. Remote Control...........................................................................6
2.3.1. General functions .....................................................6
2.3.2. Inserting the batteries in the remote
control.............................................................................7
2.3.3. Handling the remote control.............................7
2.3.4. Operating range of the remote control......7
3. Connecting External Equipment.............................................8
3.1. Connecting External Equipment
(DVD/VCR/VCD) .......................................................................8
3.1.1. Using COMPONENT video input.................8
3.1.2. UsingVideo Source input.....................................8
3.1.3. Using HDMI video input......................................8
3.2. Connecting a PC..........................................................................9
3.2.1. UsingVGA input........................................................9
3.2.2. Using DVI input .........................................................9
3.2.3. Using HDMI input....................................................9
3.2.4. Using DisplayPort input.....................................10
3.3. Connecting Audio Equipment...........................................10
3.3.1. Connecting external speakers........................10
3.3.2. Connecting an external audio device........10
3.4. Connecting Multiple Displays in a Daisy-chain
Conguration..............................................................................11
3.4.1. Display control connection..............................11
3.4.2. Digital video connection....................................11
3.5. IR connection..............................................................................11
3.6. IR Pass-through Connection...............................................12
3.7. Wire-connecting to Network ...........................................12
4. Operation................................................................................. 13
4.1. Watch the ConnectedVideo Source............................13
4.2. Play multimedia les from USB device.........................13
4.3. Play options..................................................................................13
4.3.1. Playing music les ..................................................13
4.3.2. Playing movie les .................................................13
4.3.3. Playing photo les .................................................13
4.4. How to use Opera browser (HTML5) .......................13
5. OSD Menu ............................................................................... 15
5.1. Navigating the OSD Menu................................................15
5.1.1. Navigating the OSD menu using the
remote control........................................................15
5.1.2. Navigating the OSD menu using the
display’s control buttons....................................15
5.2. OSD Menu Overview...........................................................15
5.2.1. Picture menu............................................................15
5.2.2. Screen menu............................................................16
5.2.3. Audio menu..............................................................17
5.2.4. PIP menu ....................................................................17
5.2.5. Conguration1 menu..........................................18
5.2.6. Conguration2 menu..........................................19
5.2.7. Advanced option menu.....................................20
5.2.8. Input menu................................................................23
6. USB device compatibility....................................................... 24
7. Input Mode............................................................................... 26
8. Pixel Defect Policy.................................................................. 27
8.1. Pixels and Sub-Pixels...............................................................27
8.2. Types of Pixel Defects + Dot Denition....................27
8.3. Bright Dot Defects...................................................................27
8.4. Dark Dot Defects.....................................................................28
8.5. Proximity of Pixel Defects...................................................28
8.6. Pixel DefectTolerances .........................................................28
8.7. MURA .............................................................................................28
9. Cleaning and Troubleshooting.............................................. 29
9.1. Cleaning..........................................................................................29
9.2. Troubleshooting.........................................................................30
10. Technical Specications ......................................................... 31

BDL8470EU
1
1. Unpacking and Installation
1.1. Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package content:
• LCD display
• CD ROM
• Quick start guide
• Remote control with AAA batteries
• Power cord (1.8 m)
• VGA cable (1.8 m)
• RS232 cable (3 m)
• RS232 daisy chain cable (3 m)
• Logo guider & Logo
* The supplied power cord varies depending on destination.
Power Cord Logo guider & Logo
CD ROMQuick start guide
Remote Control
and AAA Batteries
RS232 Daisy Chain Cable
VGA Cable
RS232 Cable
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
VOL
NORMAL ID
IDSET ENTER
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the
safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
1.3. Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
• The product should be installed on a at surface to avoid tipping. The distance between the back of the product and the wall should be maintained
for proper ventilation.Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced.

BDL8470EU
2
1.4. Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available).We recommend using a mounting interface
that complies with TUV-GS and/or UL1678 standard in North America.
Protective Sheet
VESA Grid
Carrying handleTable
Eye bolt
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M8 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them
securely.
1.4.1. VESA Grid
BDL8470EU 600(H) x 500(V) mm
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation
instructions, refer to the guide received with the respective bracket.
• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the
bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the
diagram below.
100 mm 100 mm
100 mm
100 mm

BDL8470EU
3
1.5. Mounting in Portrait Position
This display can be installed in portrait position.
1. Remove the table stand, if attached.
2. Rotate 90 degrees clockwise.The “ ” logo should be on the LEFT side when facing the display.
90 90
1.5.1. How to use the logo guider for portrait position
1. Put the guider on the lower-left corner of the front bezel of the display.
Fold down both of its edges.
2. Peel off the protective lm at the back of the “ ” logo sticker.
Hold and press the guider with your left hand. Put the “ ” logo
sticker with its adhesive side down into the logo hole with your right
hand, and press to make it stick tightly onto the front bezel.
3. Remove the guider.
1.5.2. How to remove the logo
1. Prepare a piece of paper with a cutting area of logo as a protector to
prevent the front bezel from scratching.
2. Using a knife, carefully remove the logo sticker with the paper placing
beneath.
3. Tear off the logo sticker.
123
NOTE: When installing the display on a wall, please consult a professional technician for proper installation.We accept no liability for installations not
performed by a professional technician.

BDL8470EU
4
2. Parts and Functions
2.1. Control Panel
1 2 3 4 5 6 7 8
MUTE INPUT MENU
9
1[ ] button
Use this button to turn the display on or put the display to standby.
2[MUTE] button
Switch the audio mute ON/OFF.
3[INPUT] button
Use this button to select the input source.
4[ ] button
Increase the adjustment while OSD menu is on, or increase the
audio output level while OSD menu is off.
• Used as [ ] button in the On-Screen-Display menu.
5[ ] button
Decrease the adjustment while OSD menu is on, or decrease the
audio output level while OSD menu is off.
6[ ] button
Move the highlight bar up to adjust the selected item while OSD
menu is on.
7[ ] button
Move the highlight bar down to adjust the selected item while OSD
menu is on.
8[MENU] button
Return to previous menu while OSD menu is on, or to activate the
OSD menu when OSD menu is off.
9
Remote control sensor and power status indicator
• Receives command signals from the remote control.
• Indicates the operating status of the display:
-Lights green when the display is turned on.
-Lights red when the display is in standby mode.
-Lights amber when the display enters power save mode or
deep sleep mode.
-When {SCHEDULE} is enabled, the light blinks green and red.
-If the light blinks red, it indicates that a failure has been
detected.
-Lights off when the main power of the display is turned off.
• Push up to hide the lens:

BDL8470EU
5
2.2. Input/Output Terminals
1 32
5
6
17
19
21
7
4
8
9
10
11 12
13 14
15
16
18
20
1AC IN
AC power input from the wall outlet.
2MAIN POWER SWITCH
Switch the main power on/off.
3HDMI1 IN / HDMI2 IN / HDMI3 IN
HDMI video/audio input.
4RS232C IN / 5RS232C OUT
RS232C network input / output for the loop-through function.
6DVI IN
DVI-D video input.
7DisplayPort IN / 8DisplayPort OUT
DisplayPort video input / output.
9VGA IN (D-Sub)
VGA video input.
10 IR IN / 11 IR OUT
IR signal input / output for the loop-through function.
NOTES:
• This display’s remote control sensor will stop working if the jack
[IR IN] is connected.
• To remotely control your A/V device via this display, refer to page
12 for IR Pass Through connection.
12 SPDIF OUT
Digital audio output
13 AUDIO IN
Audio input forVGA source (3.5mm stereo phone).
14 AUDIO OUT
Audio output to external AV device.
15 SPEAKER SWITCH
Internal speaker on/off switch.
16 SPEAKERS OUT
Audio output to external speakers.
17 RJ-45
LAN control function for the use of remote control signal from
control center.
18 Y/CVBS
Video source input.
19 COMPONENT IN
ComponentYPbPr video source input.
20 AUDIO IN
Audio inpu+t from external AV device (RCA).
21 USB PORT
Connect your USB storage device.

BDL8470EU
6
2.3. Remote Control
2.3.1. General functions
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
VOL
NORMAL ID
ID SET ENTER
110
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
1[ ] POWER button
Turn the display on or put the display to standby.
2[PLAY] buttons
Control playback of media les.
3[ ] SOURCE button
Choose input source. Press [ ] or [ ] button to choose from
DisplayPort, DVI-D, VGA. HDMI 1, HDMI 2, HDMI 3,
Component, Video, USB, BROWSER, SmartCMS, or
Card OPS. Press [ ] button to conrm and exit.
4[ ] HOME button
Access the OSD menu.
5[ ] LIST button
No function.
6[ ] [ ] [ ] [ ] NAVIGATION buttons
Navigate through menus and choose items.
7[ ] ADJUST button
To auto adjust forVGA input only.
8[ ] MUTE button
Press to turn the mute function on/off.
9[ ] [ ] [ ] [ ] COLOR buttons
Choose tasks or options.
10 [NORMAL] buttons
Switch to normal mode.
11 [ID] buttons
Switch to ID mode.
12 [ ] FORMAT button
Change zoom mode.
13 [ ] BACK button
Return to the previous menu page or exit from the previous
function.
14 [ ] INFO button
Display information about current activity.
15 [ ] button
Conrm an entry or selection.
16 [ ] OPTIONS button
Access currently available options, picture and sound menus.
17 [ ] [ ] VOLUME button
Adjust volume.
18 [NUMERIC] buttons
Enter text for network setting, and set up ID for ID mode.

BDL8470EU
7
2.3.2. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:
• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can
damage your skin.
NOTE: If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
• Do not subject to strong shock.
• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the top of the remote control toward the display’s remote control sensor when
pressing a button.
Use the remote control within a distance of less than 5m (pull down lens, control from
the front) /26ft from the display’s sensor, and a horizontal and vertical angle of less than
20 degrees.
NOTE: The remote control may not function properly when the remote control
sensor on the display is under direct sunlight or strong illumination, or when
there is an obstacle in the path of signal transmission.
20 20
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
VOL
NORMAL ID
IDSET ENTER

BDL8470EU
8
3. Connecting External Equipment
3.1. Connecting External Equipment (DVD/VCR/VCD)
3.1.1. Using COMPONENT video input
DVD / VCR / VCD
[AUDIO IN]
[COMPONENT IN]
(YPbPr) COMPONENT Out
(YPbPr) Audio Out
[R]
[L]
3.1.2. Using Video Source input
DVD / VCR / VCD
[AUDIO IN]
Audio Out
[R]
[L]
[Y/CVBS IN] Y/CVBS Out
3.1.3. Using HDMI video input
DVD / VCR / VCD
HDMI Out
[HDMI IN]

BDL8470EU
9
3.2. Connecting a PC
3.2.1. Using VGA input
PC
[VGA IN]
[VGA AUDIO IN] VGA Out
D-Sub 15 pin
Audio Out
3.2.2. Using DVI input
PC
DVI Out
[DVI IN]
[VGA AUDIO IN] Audio Out
3.2.3. Using HDMI input
PC
HDMI Out
[HDMI IN]

BDL8470EU
10
3.2.4. Using DisplayPort input
PC
DisplayPort Out
[DisplayPort IN]
3.3. Connecting Audio Equipment
3.3.1. Connecting external speakers
External speakers
3.3.2. Connecting an external audio device
Stereo Amplifier
[AUDIO OUT] Audio In
[SPDIF OUT]

BDL8470EU
11
3.4. Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain conguration for applications such as a video wall.
NOTE: Maximum 25 displays (5x5) can be used in a daisy-chain conguration.
3.4.1. Display control connection
Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2.
DISPLAY 1 DISPLAY 2
PC
[RS-232C IN]
[RS-232C]
[RS-232C OUT] [RS-232C IN]
3.4.2. Digital video connection
Connect the [DP OUT] connector of DISPLAY 1 to the [DP IN] connector of DISPLAY 2.
DISPLAY 1 DISPLAY 2
PC
[DP IN]
[DP]
[DP OUT] [DP IN]
3.5. IR connection
DISPLAY 1 DISPLAY 2
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
VOL
NORMAL ID
IDSET ENTER
[IR IN]
[IR OUT]
[IR IN]
External
IR Receiver
NOTE: This display’s remote control sensor will stop working if the [IR IN] is connected.