Philips VR 260/07 User manual

TTaabblleeooffccoonntteennttss
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
Introduction
Connecting the
video recorder
Initial
installation
Settings
Operating
instructions
Playback
Removing picture
interference
Manual
recording
Programmed
recordings
Other
functions
Suppressing
interference
Before you call
an engineer
Important notes for operation . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
The most important functions of your new video recorder. . . . . . .Page 5
Important information for customers in Great Britain . . . . . . . . . .Page 6
Preparing the remote control for operation . . . . . . . . . . . . . . . . .Page 7
Connecting to a TV set with a scart socket . . . . . . . . . . . . . . . . . .Page 7
Connecting to a TV set without a scart socket . . . . . . . . . . . . . . .Page 8
Connecting additional devices . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Setting TV channels,date and time for thefirst time . . . . . . . . . .Page 10
Searching for TV channels manually. . . . . . . . . . . . . . . . . . . . . . .Page 11
Allocating decoder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Using a satellite receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
Searching for a TV channel automatically. . . . . . . . . . . . . . . . . . .Page 14
Sorting and clearing of TV channels manually. . . . . . . . . . . . . . . .Page 15
Changing the time anddate . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 16
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
Navigation in the main menu. . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 17
Playing cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Playing back NTSC cassettes. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 18
Selecting tape position display type . . . . . . . . . . . . . . . . . . . . . . .Page 19
Reset / display tape position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 20
Searching for tape position with picture (picture search) . . . . . . .Page 20
Searching for tape position without picture (forward wind and rewind) . . .Page 20
Searching automatically for tape position (index search) . . . . . . .Page 21
Finding a blank position on tape automatically. . . . . . . . . . . . . . .Page 21
Still picture / slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Skip commercials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 22
Optimizing tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 23
Optimizing still picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 23
Starting and stopping of recording manually. . . . . . . . . . . . . . . .Page 24
Starting recording manually and stopping automatically. . . . . . . .Page 25
Lining up manual recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 26
Selecting the recording speed . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 26
Recording automatically from a satellite receiver. . . . . . . . . . . . . .Page 27
Activate / deactivate direct recording. . . . . . . . . . . . . . . . . . . . . .Page 28
Making a direct recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 29
Programming timer with VIDEO Plus+ . . . . . . . . . . . . . . . . . . . . .Page 30
Problem solving (VIDEOPlus-Programming) . . . . . . . . . . . . . . . .Page 32
Programming timer without VIDEO Plus+ . . . . . . . . . . . . . . . . . .Page 33
Problem solving (Timer programming) . . . . . . . . . . . . . . . . . . . . .Page 35
Turbo Timer-Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 36
Problem solving (Turbo Timer programming). . . . . . . . . . . . . . . . .Page 37
Delete / check / change programmed recordings . . . . . . . . . . . . .Page 38
Using the NexTView Link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 38
Adjusting automatic switch-off . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 39
Adjusting the child lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 39
Replaying cassette continuously. . . . . . . . . . . . . . . . . . . . . . . . . . .Page 40
Changing the TV system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 41
Adjusting the OSD information. . . . . . . . . . . . . . . . . . . . . . . . . . .Page 42
Energy-saving mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 43
Adapting remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 44
Using the TV remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 45
Optimizing the modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 46
Switching the modulator on / off . . . . . . . . . . . . . . . . . . . . . . . . .Page 47
Problem solving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 48
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 48

VR 260/07
Operating instructions
with

REMOTE CONTROL ENGLISH
2
2
RReemmootteeccoonnttrrooll
EEJJEECCTTJJä Eject inserted cassette
SSTTAANNDDBBYY//OONNmmäSwitch set on / off
äInterrupt function
äInterrupt programmed recording
CCLLEEAARR//CCLLäDelete entry
äDelete programmed recording
SSEELLEECCTTäSelect function
CCHHIILLDDLLOOCCKKuuä Activate / deactivate child lock
MMOONNIITTOORRä Change between TV reception and video
recorder reception
You will find explanations
for the controls and the
displays on your video
recorder on the second
to last page of these
operating instructions.
TTIIPP
HHäIn STOP or STANDBY mode: Rewind
äIn playback mode: Fast reverse
PPLLAAYYGGäPlay back recorded cassette
IIäIn STOP or STANDBY mode:Wind forward
äIn playback mode: Fast forward
SSTTOOPPhhäStop tape
RREECCOORRDD//OOTTRRnnäStart manual recording
IINNDDEEXXEEäWith HHor II: Search for index
marking
SSTTIILLLLRRäStop tape and show still picture
4 Operating instructions
4Quick Start Guide
4Remote control
4Batteries
4Aerial cable
4Mains cable
4Scart cable
TTVVffuunnccttiioonnss
++SS--äIncrease / reduce TV volume
yy//TTVVäSwitch sound on / off
TTVV//mmäSwitch TV on / off
++TTVV--äSelect next / previous programme number
AAcccceessssoorriieess
00--99äEnter data
äSelect programme number
TTUURRBBOOTTIIMMEERRäProgramme Turbo Timer recordings
TTIIMMEERRkkäProgramme recordings
äCheck / change recordings
äDelete recordings
MMEENNUUäSwitch main menu on / off
OOKKäStore
äConfirm
;;PP++//==PP--äSelect next / previous menu point
äSelect next / previous programme number
QQ//PPäSelect input field

IMPORTANT NOTES FOR OPERATION ENGLISH
4
4
IInnttrroodduuccttiioonn
1
1
You should not under any circumstances open the set yourself.
You would expose yourself to the risk of an electric shock from
the hazardous high voltage inside.
IImmppoorrttaannttnnootteessffoorrooppeerraattiioonn
WWeellccoommeettootthheeffaammiillyyooffoowwnneerrssooffPPhhiilliippssVVHHSSvviiddeeoo
rreeccoorrddeerrss..
Thank you for choosing to buy our product. Please wait at
least three hours after transporting the appliance before
starting installation. The set needs this time in order to
become acclimatised to its new environment (temperature, air
humidity, etc.).
YYoouurrPPhhiilliippssTTeeaammhhooppeesstthhaattyyoouu
wwiilllleennjjooyyuussiinnggyyoouurrnneewwvviiddeeoo
rreeccoorrddeerr..
When the appliance is connected to the power supply, there are some
components which are constantly operational.To switch off the video
recorder completely, you must disconnect it from the power supply.
The video recorder does not contain any components that can be
repaired by the customer.
Make sure that air can circulate freely through the ventilation slots
on the video recorder.
Make sure that no objects or liquids enter the video recorder. If liquid is
spilt into it, disconnect the video recorder immediately from the power
supply and call the After Sales Service for advice.
The video recorder should not be used immediately after
transportation from a cold to a hot area or vice versa, or in
conditions of extreme humidity.
These operating instructions have been printed on non-polluting paper.
Please deposit old batteries at the relevant collection points.
Please make use of the facilities available in your country for disposing of the
video recorder packaging in a way that helps to protect the environment.
This electronic device contains many materials which can be recycled.
Please enquire about the possibilities for recycling your old set.
This product complies with the requirements of Directive 73/23/EEC + 89/336/EEC + 93/68 EEC.
!
!

ENGLISH THE MOST IMPORTANT FUNCTIONS
5
5
MODEL NO. VR 260/07
PROD. NO. ..............................
So that you can identify your machine in the event of theft, enter the serial number (PROD. NO)
here.You will find it on the type plate on the back of the set.
TThheemmoossttiimmppoorrttaannttffuunnccttiioonnssooffyyoouurrnneewwvviiddeeoorreeccoorrddeerr
Your Philips video recorder can be used, not only for recording and playing back VHS
cassettes, but it also has a whole range of special functions which will make day-to-day
use of your new video recorder easier for you.
Plug in and off you go - getting started with your new video recorder just couldnt be simpler. Once you
have connected the cables, you will immediately see text on the screen which will assist you at all stages
of operation.
Philips has developed a system which makes it possible for you to get the best possible playback quality
from video cassettes. Interference on old, often-played tapes is minimised, and in new or high quality
cassettes, details are even clearer.
The precision mechanism developed by Philips guarantees short rewind times and, by automatically
detecting the length of the tape, makes operation as easy as possible for the user.
The simple programming system for video recorders revolutionized the video world when it was
introduced. Instead of having to enter many different details (date, starting time, finish time, programme),
which was often tiresome and liable to errors, all you have to do is enter a number, up to nine digits long,
which can be found in any TV programme listing. Once you have done that, all the relevant details for the
recording are stored.
VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation.
The VIDEO Plus+ system is manufactured under licence from Gemstar Development Corporation.
Using the enclosed multi-code remote control you can, if you wish, control the main functions of your
TV set - even if your TV is not made by Philips.
IIffyyoouuhhaavveeaannyypprroobblleemmssuussiinnggtthheevviiddeeoorreeccoorrddeerr,,pplleeaasseerreeaaddtthheeccoorrrreessppoonnddiinngg
cchhaapptteerrssiinntthhiissiinnssttrruuccttiioonnmmaannuuaall..IIffyyoouuhhaavveeaannyyqquueessttiioonnss,,tthheerreeiissaallssooaaccuussttoommeerr
ssuuppppoorrttsseerrvviicceeaavvaaiillaabblleeiinnyyoouurrccoouunnttrryy..YYoouuccaannffiinnddtthheetteelleepphhoonneennuummbbeerriinntthhee
gguuaarraanntteeeeiinnffoorrmmaattiioonneenncclloosseeddiinntthheeppaacckkaaggiinngg..PPlleeaasseehhaavveeyyoouurrmmooddeellnnuummbbeerr
((MMOODDEELLNNOO..))aannddpprroodduuccttiioonnnnuummbbeerr((PPRROODD..NNOO..))rreeaaddyy..

IMPORTANT INFORMATION FOR CUSTOMERS IN GREAT BRITAIN ENGLISH
6
6
IImmppoorrttaannttiinnffoorrmmaattiioonnffoorrccuussttoommeerrssiinnGGrreeaattBBrriittaaiinn
This set is fitted with an approved moulded 13 amp plug.To change the fuse in this plug or to
attach a different plug, please proceed as follows:
1Take off the fuse cover and remove the old fuse
2Insert a new fuse. Suitable fuses are those of the type BS 1362 3A, A.S.T.A.
standard or BSI standard
3Close the fuse cover
If the attached plug does not meet your requirements, you can cut it off and replace it with a
suitable plug. Please observe the following conditions:
If your new plug uses a built-in fuse, this should be a 3A fuse.
If your new plug does not contain a built-in fuse, please do not use any fuses in your fusebox with a rating
of more than 5A.
Please destroy the old, cut-off plug so that it cannot be used elsewhere.
4Connect the blue cable (neutral N) to the terminal in the plug which is
marked with the letter N or coloured black
5Connect the brown cable (live,L) to the terminal in the plug which is marked
with the letter L or coloured red
6Do not in any circumstances connect either of the two cables to the terminal
in the plug which is marked with the letter E, the symbol  \ or coloured
green or green / yellow
Before you refit the plug cover, make sure, that the grip at the bottom of the plug is clamped
over the plastic cover of the lead, not just over the two wires.
!
!

ENGLISH R EMOTE CONTROL / CONNECTION WITH A SCART SOCKET
7
7
CCoonnnneeccttiinnggtthheevviiddeeoorreeccoorrddeerr
2
2
CCoonnnneeccttiinnggttooaaTTVVsseettwwiitthhaassccaarrttssoocckkeett
2Switch off your TV set
3Remove the aerial cable plug from the back of
your TV set and insert it into the aerial
socket
22on the back of the video recorder
4Take the enclosed aerial cable and connect
the appropriate end to the aerial socket of
your TV set and to the TV socket 33on the
back of the video recorder
1Have the following cables ready:An aerial cable
(enclosed), a mains cable (enclosed) and a scart
cable (enclosed)
PPAARRDDOONN??
WWhhaattiissaassccaarrttccaabbllee??
The scart or Euro-AV cable serves as the universal
recording and playback connector for picture-, sound-
and control signals.With this type of connection,there
is practically no loss of quality during the signal
transfer. We recommend that you use a scart cable
when using this video recorder.
PPrreeppaarriinnggtthheerreemmootteeccoonnttrroollffoorrooppeerraattiioonn
1Take the remote control of the video recorder
and the enclosed batteries (2 batteries)
2Open the battery compartment, insert the
batteries as shown and then close the battery
compartment.The remote control is now ready
to use
Scart cable
Aerial cable
Mains cable

CONNECTING TO A TV SET WITHOUT SCART SOCKET ENGLISH
8
8
5Take a scart cable and connect one end to the
scart socket on the back of your TV set and
the other to the scart socket AAVV11EEXXTT11on
the back of the video recorder
6Take the enclosed mains cable and connect
the appropriate end to the mains socket 44
on the back of the video recorder and the
other to the nearest free socket
1Have the following cables (provided with your
new video recorder) ready: An aerial cable
and a mains cable
2Switch off your TV set
CCoonnnneeccttiinnggttooaaTTVVsseettwwiitthhoouuttaassccaarrttssoocckkeett
8You can find more details in the chapter
Initial Installation
7Your set should automatically switch over to
the programme number allocated to video
recorder operation (usually: EXT, 0 or AV).You
will see the welcome screen
CONGRATULATIONS
YOU NOW OWN A NEW
PHILIPS
VIDEO RECORDER
CONTINUEPOK
PPRROOBBLLEEMM
88MMyyssccrreeeenniissssttiillllbbllaannkk
44If a TV set receives a signal via the scart socket, it
usually switches automatically to the
corresponding programme number. This
automatic function might be adversely affected.
Please switch manually to the corresponding
programme number (usually: EXT, 0 or AV)
44Check the connections
Aerial cable
Mains cable
PPRROOBBLLEEMM
88IIccaannttsseeeeaawweellccoommiinnggmmeessssaaggeeoonnssccrreeeenn,,jjuusstttthhee
mmeessssaaggeeEEAASSYYLLIINNKKIISSLLOOAADDIINNGGDDAATTAAFFRROOMMTTVV
44Congratulations! Your TV set supports the Easylink
function. It automatically sends the settings for the
available TV channels and the time and date
information straight to the video recorder.As soon
as the transfer is complete, the current settings for
year, month, date and time appear on the screen.
Correct and/or confirm the settings with the arrow
buttons ;PP++,=PP--,Qand/or Pthe number buttons
00--99and confirm with OOKK.
AV1 EXT1

ENGLISH C ONNECTING ADDITIONAL DEVICES
9
9
5Take the enclosed mains cable and connect
the appropriate end to the mains socket 44
on the back of the video recorder and the
other to the nearest free socket
6Switch on your TV set and select on your TV
set the programme number which will in
future be used for operation with the video
recorder
7On your TV change the settings of this
programme number until you see the
adjacent welcome screen clearly and in
colour on the screen
PPRROOBBLLEEMM
8Switch off the video recorder with the
standby button mm
88TThheerreeiissnnootteessttiimmaaggee
44Your video recorder broadcasts on the
frequency 583MHz (CH35) in the UHF range (ultra
highfrequency). Repeat the matching of the
selected programme numbers on the TV set.
44Check the cable connections
3Remove the aerial cable plug from the back of
your TV set and insert it into the aerial
socket
22on the back of the video recorder
4Take the enclosed aerial cable and connect
the appropriate end to the aerial socket of
your TV set and to the TV socket 33on the
back of the video recorder
CONGRATULATIONS
YOU NOW OWN A NEW
PHILIPS
VIDEO RECORDER
CONTINUEPOK
CCoonnnneeccttiinnggaaddddiittiioonnaallddeevviicceess
Additional devices, such as a decoder, camcorder, satellite receiver, etc., can be
connected to the scart socket AAVV22EEXXTT22on the back of the video recorder.
You will need a scart cable for this (available from specialist stores).
AV2 EXT2

SETTING TV CHANNELS,DATE AND TIME ENGLISH
10
10
1Using the OOKKbutton activate the automatic
initial installation
SSeettttiinnggTTVVcchhaannnneellss,,ddaatteeaannddttiimmeeffoorrtthheeffiirrssttttiimmee
IInniittiiaalliinnssttaallllaattiioonn
3
3
TTIIPP
2The set seeks out and stores all available TV
channels as well as time and date. This
procedure may take several minutes.As soon
as all the data has been stored,the screen will
show the message STORED.
AAiimmccoorrrreeccttllyy
Always point the remote control at the video recorder
and not at the TV set.
AUTO INSTALL
SEARCHING
00 TV CHANNELS FOUND
hhhh_______________
PLEASE WAIT...
3The initial setting of channel, date and time is
completed
TTIIPP
TThheeTTeelleetteexxttcclloocckkrreesseettssaauuttoommaattiiccaallllyy
If a TV channel which has Teletext is stored as
programme number P01, the video recorder
automatically takes in the date and time from the text
function.The change from summer to winter time and
vice versa should also occur automatically.
If your TV set supports the Easylink function and you have already
corrected and/or confirmed the settings for year, month, date and time,
you can skip this section.Your video recorder has already stored all the
necessary details.Please continue by reading the sub-section Searching
for a TV channel manually.
PPRROOBBLLEEMM
88TThheettiimmeeiissnnoottsshhoowwnniinntthheeddiissppllaayyoofftthheevviiddeeoo
rreeccoorrddeerr((--::--))oorriisssshhoowwnniinnccoorrrreeccttllyy
44While initial installation was going on, the set was
unable to recognise the time. Please read the
paragraph in Section 4 Setting the time and
date to correct this problem
PPRROOBBLLEEMM
88DDeessppiitteeaaccoonnttiinnuueeddsseeaarrcchhtthheevviiddeeoorreeccoorrddeerr
ffiinnddssnnooTTVVcchhaannnneellss((00 TV CHANNELS FOUND))
44Please be patient!The video recorder will search
through the entire frequency range in order to
identify the maximum possible number of
available TV channels. TV channels transmitted in
your country may use a higher frequency band.
As soon as this range is reached, the video
reorder will find all available channels.

ENGLISH SEARCHING FOR A TV CHANNEL MANUALLY
11
11
1Switch on the TV set and - if necessary -
select the programme number set for video
recorder operation
SSeeaarrcchhiinnggffoorraaTTVVcchhaannnneellmmaannuuaallllyy
3Use ==PP--or ;;PP++to select the option
MANUAL SEARCH
5Use PPor QQ(or 00--99) to select the
programme number (e.g.:P01), which you
want to manually allocate to a TV channel
7Use ==PP--or ;;PP++to select the option CHANNEL
NUMBER and use PPor QQ(or 00--99) to enter
the number of the TV-Channel required
2Press the MMEENNUUbutton on the remote
control.The on-screen menu appears
6If you are looking for a special channel, use
==PP--or ;;PP++to select the option S-
CHANNEL and use PPor QQto activate the
YES setting. To search for a normal
channel, the NO setting must be selected
PPAARRDDOONN??
WWhhaattiissaacchhaannnneell,,oorraassppeecciiaallcchhaannnneell??
TV channels are transmitted on precisely-defined
frequency ranges.These ranges are also referred to as
channels. Each channel has its own TV station
allocated to it. Most cable and satellite TV providers
supply tables of channel allocations. Special channels
(hyperband channels) are transmitted on special
frequencies.
In exceptional cases, it may happen that on initial installation the
set does not find all the available TV channels. In this case, the
missing TV channels must be searched for and stored manually. If
your set supports the Easylink function, you can start the
automatic transfer of channel data by means of the following steps.
4Confirm with OOKK
MANUAL SEARCH
PROGRAMME NUMBER QP01P
S-CHANNEL NO.
CHANNEL NUMBER 21
DECODER OFF
EXITPMENU STOREPOK
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK
PPAARRDDOONN??
WWhhaattiissaannoonn--ssccrreeeennmmeennuu??
The on-screen menu takes the mystery out of using
your new video recorder. All settings and recording
steps can be done easily via the on-screen menu by
following the corresponding instructions on the
screen.

12
12
ALLOCATING DECODER ENGLISH
88IIddoonnttkknnoowwtthheecchhaannnneellssffoorrmmyyTTVVssttaattiioonnss
44No problem. Hold down the button PPto start
the automatic channel search. A changing channel
number will appear on screen. Continue the
automatic channel search until you have found the
desired TV station PPRROOBBLLEEMM
8Press OOKKto store the TV channel found.The
screen will briefly show STORED
PPRROOBBLLEEMM
88IIccaannttffiinnddtthheeTTVVcchhaannnneellssffrroommmmyyssaatteelllliittee
rreecceeiivveerr
44These do not have to be stored as actual TV
channels. On your video recorder, select the
programme number E2. Individual TV channels
must be selected on the actual satellite receiver itself
9Finish manual searching of TV channels by
pressing the MMEENNUUbutton or return to step
3to allocate additional TV channels
1Use ==PP--and ;;PP++or the number keys 00--99to
select the TV channel, which will in future be
automatically decoded by your decoder
AAllllooccaattiinnggddeeccooddeerr
2Press the MMEENNUUbutton
PPAARRDDOONN??
WWhhaattiissaaddeeccooddeerr??
Like a deciphering machine, a decoder (available in TV
and video stores) deciphers theTV channels for which
additional charges must be paid. Without the
appropriate decoder, you will receive these TV
channels distorted.
If your TV set supports the Easylink function you must allocate
the decoder directly to the TV set. If necessary, you should refer
to the instructions for your TV set for assistance.

13
13
ENGLISH USING A SATELLITE RECEIVER
UUssiinnggaassaatteelllliitteerreecceeiivveerr
Those TV channels which are received via a satellite receiver
connected (to the scart socket AAVV22EEXXTT22) can be viewed on the
video recorder on programme number E2. On the remote
control press the number button 00and then the button ==PP--to
select this programme number. The TV channels of the satellite
receiver are selected not on the video recorder itself,but directly
on the satellite receiver.
3The on-screen menu appears. Use the buttons
==PP--and ;;PP++to select the menu point MANUAL
SEARCH and confirm with OOKK
4Use ==PP--or ;;PP++to select the option
DECODER
5Using PPor QQ, activate the setting ON.The
display will show DEC. When selecting
OFF the decoder will not be allocated
PPAARRDDOONN??
WWhhaattiissaannoonn--ssccrreeeennmmeennuu??
The on-screen menu takes the mystery out of using
your new video recorder. All settings and recording
steps can be done easily via the on-screen menu by
following the corresponding instructions on the
screen.
6Confirm with OOKKand leave the on-screen
menu with the MMEENNUUbutton.The screen will
show the message STORED
TTIIPP
CChheecckkddeeccooddeerraallllooccaattiioonnaattaaggllaannccee
There is no need to call up the on-screen menu to check
to whichTV channel on the video recorder a decoder is
allocated. Simply use ==PP--and ;;PP++to select a TV channel.
If DEC appears in the display, a decoder is allocated to
this channel.
MANUAL SEARCH
PROGRAMME NUMBER QP01P
S-CHANNEL NO.
CHANNEL NUMBER 21
DECODER OFF
EXITPMENU STOREPOK
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK

14
14
SEARCHING FOR TV CHANNELS AUTOMATICALLY ENGLISH
SSeettttiinnggss
4
4
1Switch on the TV set and - if necessary -
select the programme number set for video
recorder operation
SSeeaarrcchhiinnggffoorrTTVVcchhaannnneellssaauuttoommaattiiccaallllyy
4The set seeks out and stores all available TV
channels. This procedure may take several
minutes. As soon as all the TV channels have
been stored, the screen will show the
message STORED
On initial installation, the video recorder performs an automatic
channel search. If the channel assignments of your cable or
satellite TV provider change or if you are reinstalling the video
recorder, e.g. after moving house, you can start this procedure
again. The video recorder finds all the available TV channels and
stores the new settings.If your set supports the Easylink function,
you can start the automatic transfer of channel data by means of
the following steps.
3Use ==PP--or ;;PP++to select the option AUTO
INSTALL (automatic channel search) and
confirm with OOKK
2Press the MMEENNUUbutton on the remote
control.The on-screen menu appears
88TThheevviiddeeoorreeccoorrddeerriissnnoottffiinnddiinnggaalllltthheeTTVV
cchhaannnneellss
44In exceptional cases, it may happen that the set
does not find all the available TV channels. In this
case, the missing TV channels must be searched
for and stored manually.You can look up how to
do this in the chapter Initial installation
(Searching for a TV channel manually). PPRROOBBLLEEMM
AUTO INSTALL
SEARCHING
00 TV CHANNELS FOUND
hhhh_______________
PLEASE WAIT...
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK
TTIIPP
SSeeqquueenncceeooffTTVVcchhaannnneellss
TV channels are stored in the following sequence: BBC1,
BBC2, ITC, CH 4, CH 5, others.
5Finish with the button MMEENNUU

15
15
ENGLISH SORTING AND CLEARING OF TV CHANNELS MANUALLY
SSoorrttiinnggaannddcclleeaarriinnggooffTTVVcchhaannnneellssmmaannuuaallllyy
After you have performed the automatic channel search you may
not agree with the sequence in which the individual TV channels
have been allocated to the programme positions of the video
recorder. You can use this function to individually sort the TV
channels found or to delete unwantedTV channels or those with
poor reception. If your TV set supports the Easylink function, you
will not need to rearrange the TV channels later. The sequence
corresponds to the channel allocation of your TV set.
1Switch on theTV set and - if necessary - select
the programme number set for video recorder
operation
3Use ==PP--or ;;PP++to select the option
TV CHANNEL ALLOC. and confirm with OOKK
2Press the MMEENNUUbutton on the remote
control.The on-screen menu appears
4Use PPor QQto select the TV channel, to be
allocated a programme position
5SSoorrttiinngg::Press SSEELLEECCTT, to allocate theTV
channel to the programme
position set P01
CClleeaarriinngg::Delete the TV channel set with
CCLLEEAARR((CCLL))
6Continue repeating the steps 4and 5,to
allocate additional TV channels (P02,P03,...)
or to delete additional TV channels and
confirm with OOKK
7Finish the manual sorting and clearing of
TV channels with the button MMEENNUU
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK
TV CHANNEL ALLOC.
ALLOCATE ON QP01P
TV CHANNEL BBC1
ALLOCATEPSELECT EXITPMENU

16
16
CHANGING THE TIME AND DATE ENGLISH
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK
CLOCK
YEAR Q2000P
MONTH 01
DATE 01
TIME 20:00
EXITPMENU STOREPOK
CChhaannggiinnggtthheettiimmeeaannddddaattee
3In the YEAR option  if the setting displayed
is incorrect - enter the number of the current
year using the number keys 00--99(or with P
and Q)
4Use ==PP--or ;;PP++to select the option MONTH
and - if the setting displayed is incorrect -
enter the current month with the number
keys
00--99(or with P and Q)
5Use ==PP--or ;;PP++to select the option DATE
and - if the setting displayed is incorrect -
enter the current calendar date with the
number keys 00--99(or with P and Q)
6Use ==PP--or ;;PP++to select the optionTIME and
- if the setting displayed is incorrect - enter the
current time with the number keys 00--99(or
with P and Q)
8Leave the on-screen menu with the MMEENNUU
button
2Use ==PP--or ;;PP++to select the option CLOCK
and confirm with OOKK
1Press the MMEENNUUbutton on the remote
control.The on-screen menu appears
If the display shows an incorrect time or  --:-- , the time and date
must be set manually.
7Check the settings displayed for year, month,
date and time and store them by pressing
OOKK. The screen will show the message
STORED
TTIIPP
TThheeTTeelleetteexxttcclloocckkrreesseettssaauuttoommaattiiccaallllyy
If you store a TV channel which has Teletext as
programme number P01, the video recorder
automatically takes in the date and time from the text
function.The change from summer to winter time and
vice versa should also occur automatically.
TTIIPP
EEnntteerrtthheevvaalluueessccoorrrreeccttllyy
Numbers less than 10 must be entered with an
additional 0.Therefore for 9 you must enter 09.

17
17
ENGLISH GENERAL INFORMATION / NAVIGATION
OOppeerraattiinnggiinnssttrruuccttiioonnss
5
5
GGeenneerraalliinnffoorrmmaattiioonn
AAuuttoommaattiiccsswwiittcchh--ooffff
If the video recorder is not used for several minutes, it switches itself off
automatically.This function can be deactivated (e.g. if you want to use the video
recorder as aTV receiver).You can find out more about this in the chapter Other
functions (Adjusting automatic switch off).
SSwwiittcchhiinnggoonnIf the video recorder is in standby mode, it can be switched on either by pressing
the Standby button mm, by pressing one of the number buttons 00--99or by inserting
a cassette.
EEnneerrggyyccoonnssuummppttiioonnThe video recorder should always be connected to the mains so as not to affect
programmed recordings and use of the TV set. Power consumption (in energy
saving mode) is less than 4W.
NNaavviiggaattiioonniinntthheemmaaiinnmmeennuu
Call up: MMEENNUU
Select: ;PP++or =PP--
Confirm: OOKK
Enter: 00--99or Pand Q
Interrupt: SSTTAANNDDBBYY//OONNmm
Abandon: MMEENNUU
IInntthheeeevveennttooffaa
ppoowweerrccuuttChannel data are stored for around 1 year, time and timer data remain in the
memory of the video recorder for around 3 hours.
You can check and / or change many functions and settings of your
video recorder via the main menu. The individual functions are
selected as follows via the on-screen menu of the video recorder
EEmmeerrggeennccyyeexxiitt
The video recorder and the remote control have the option of an Emergency
exit.You can use the Standby button mmto interrupt any step during use. But even
without an emergency brake your new video recorder is safe: there is no risk
whatsoever of damaging the set by performing user steps incorrectly.
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK
SSaavviinnggeenneerrggyy
In standby mode, the display of the video recorder shows the current time.This
display can be deactivated manually, in order to reduce power consumption to a
minimum in standby mode.You can find the necessary steps in the section Other
functions (Energy-saving mode).

18
18
PLAYING CASSETTES / PLAYING BACK NTSC CASSETTES ENGLISH
1Insert aVHS cassette in the cassette opening on
the front of the video recorder.The tape will be
caught and automatically placed in the correct
position.The display will show vv
2Press the Playback button CCto play the tape
3Press the Stop button hon the remote
control (or the Stop/Eject cassette
button ?on the front of the video
recorder) to stop the playback
PPllaayyiinnggccaasssseetttteess
4Press the Stop/Eject cassette button ?on
the front of the video recorder, to remove
the tape
PPllaayybbaacckk
6
6
PPAARRDDOONN??
88PPiiccttuurree//ssoouunnddqquuaalliittyyiissppoooorr
44Please read the section Removing picture
interference in this chapter.
44When playing many rental videos or older, poorer
quality cassettes, it may not be possible to
completely filter out picture and sound
interference. There is nothing wrong with the
video recorder. PPRROOBBLLEEMM
TTIIPP
AAuuttoommaattiiccsswwiittcchh--ooffff
Many functions (pause, still picture, search, ...) switch
themselves off automatically after a short time in order
to protect the cassette and to save energy.
WWhhaattddooeessVVHHSSmmeeaann??
The Video Home System (VHS) has become the
world-wide standard for recording and playback of
amateur video cassettes.The popular standard has since
been refined. Super-VHS (S-VHS) offers greater
sharpness and less noise, Digital-VHS (D-VHS) now only
works with digital picture and sound signals.Your video
recorder can only record and play standard VHS
cassettes.
v
P01
?
PPllaayyiinnggbbaacckkNNTTSSCCccaasssseetttteess
If you are using a PAL TV set which is capable of showing a frame
frequency of 60 Hz, you can play cassettes which have been recorded
on the NTSC standard (USA, Japan, etc.). During an NTSC playback,
some special functions (e.g. still picture) are not possible. The display
will show 60HZ

19
19
ENGLISH SELECTING TAPE POSITION DISPLAY TYPE
SSeelleeccttiinnggttaappeeppoossiittiioonnddiissppllaayyttyyppee
If the OOKKbutton is pressed during playback and recording, the
current tape position (hours : minutes : seconds) is shown in the
display.There are two different types of display available.
88TThheeccoouunntteerrssttooppssrruunnnniinnggwwhheennuunnrreeccoorrddeedd
ppllaacceessaarreeffoouunndd((LLiinneeaarrddiissppllaayyttyyppee))
44This is normal, and is necessary for technical
reasons.
88TThheeddiissppllaayysshhoowwssaanneeggaattiivveeppllaayyiinnggttiimmee
44This may happen, for example, when you insert an
incompletely-rewound cassette into the video
recorder and rewind it to the start of the tape.
Since the display is automatically reset to
00:00:00 when you insert a cassette, the
actual start of the cassette for the set is less than
zero - thus in the negative range.The tape position
is displayed with a minus sign -.
88AAfftteerriinnsseerrttiinnggaaccaasssseetttteetthheevviiddeeoorreeccoorrddeerr
sshhoowwssnnoorreemmaaiinniinnggppllaayyiinnggttiimmee
44The set needs a little time to calculate the remaining
playing time.After a few seconds, the display should
change from --:-- to the corresponding value PPRROOBBLLEEMM
2Use ==PP--or ;;PP++to select the option
SPECIAL SETTINGS and confirm with
OOKK
1Press the MMEENNUUbutton on the remote
control.The on-screen menu appears
3Use ==PP--or ;;PP++to select the option
COUNTER
4Use PPor QQto select the desired type of
display and confirm with OOKK. The screen will
show the message STORED
PPAARRDDOONN??
WWhhaattttyyppeessooffddiissppllaayyaarreeaavvaaiillaabblleettoommee??
LINEAR: The display shows the number of
minutes of tape already played
(00:00:00 - hours / minutes /
seconds)
TIME LEFT: The display shows the playing time
remaining until the end of the
cassette (00:00 - hours / minutes)
MAIN MENU
CLOCK
AUTO INSTALL
MANUAL SEARCH
TV CHANNEL ALLOC.
RECORD SPEED
AUTO STANDBY
TV SYSTEM
SPECIAL SETTINGS
EXITPMENU OK
SPECIAL SETTINGS
OSD ON
CLOCK DISPLAY OFF
COUNTER QT.LEFTP
SAT RECORDING OFF
REPEAT PLAY OFF
DIRECT RECORD OFF
EXITPMENU OK

20
20
DISPLAY / RESET / FIND TAPE POSITION ENGLISH
1During playback press H(rewind) or I
(forward)
SSeeaarrcchhiinnggffoorrttaappeeppoossiittiioonnwwiitthhppiiccttuurree
((ppiiccttuurreesseeaarrcchh))
2Interrupt the search wherever you like with
the Playback button G
TTIIPP
RReedduucceeddqquuaalliittyy
During picture search the picture quality is affected.
The sound is switched off.
DDiiffffeerreennttsseeaarrcchhssppeeeeddss
If you press Hor Itwice, the tape speed will
increase.Interrupt the search with the playback
button G.
RReesseett//ddiissppllaayyttaappeeppoossiittiioonn
Call up: OOKK
Reset: CCLLEEAARR((CCLL))(only in the
LINEAR display mode)
TTIIPP
AAuuttoommaattiiccrreesseett
Whenever a cassette is inserted the display is
automatically reset to 00:00:00.
1Stop the tape with the Stop button h
SSeeaarrcchhiinnggffoorrttaappeeppoossiittiioonnwwiitthhoouuttppiiccttuurree
((ffoorrwwaarrddwwiinnddaannddrreewwiinndd))
3Interrupt the search wherever you like with
the Playback button G
2Press H(rewind) or I(forward)
FFOORR
EEXXPPEERRTTSS
SSwwiittcchhiinnggbbeettwweeeennrreewwiinndd//ffoorrwwaarrddwwiinnddaanndd
ppiiccttuurreesseeaarrcchh((iinnssttaannttvviieeww))
When winding the tape backwards or forwards if you
hold down H(rewind) or I(forward wind), the
set will immediately switch without a break to picture
search (with picture). When you release the rewind
or forward wind button the rewind or forward wind
process (without picture) will continue