Phistek P150TR Installation and operating instructions

1
U
Us se er r M Ma an nu ua al l / / I In ns st ta al ll la at ti io on n G Gu ui id de e
M
Mo od de el l N No o. . P P1 15 50 0T TR R
Warning! This monitor is equipped with Mini USB port, signals and power is obtained from standard
USB 2.0 or USB 3.0 port. Do not e pose this unit in the rain or moisture environment to damage the
monitor.
PRECAUTIONS
Do not use the monitor near water.
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a
person and cause serious damage to the appliance. Use only a cart or stand recommended by the
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting
kit approved by the manufacturer and follows the kit instructions.
The monitor should be operated with an USB cable with Mini USB B type connector on monitor end
and standard USB A type connector on the other end to PC or USB signal source.
Normally it is packed with monitor.
Never spill liquids on the monitor.
Do not attempt to service the monitor yourself; opening or removing covers can damage to the
monitor or panel. Please refer all servicing to qualified service personnel.
For Wall mount adaptor, wall socket shall be installed near the equipment and shall be easily
accessible.


2
Index:
I. Introduction --------------------------------------------------------------------------------------------------- 3
Features--------------------------------------------------------------------------------------------------------- 3
Unpack the monitor------------------------------------------------------------------------------------------ 3
Check Accessories--------------------------------------------------------------------------------------------- 3
II. Installation----------------------------------------------------------------------------------------------------- 4-1
Installing the DisplayLink USB Graphics Software----------------------------------------------------- 4-5
Install EETI Touch Driver (For Touch Screen) ----------------------------------------------------------- 6~9
Control buttons/Connector--------------------------------------------------------------------------------- 10
Rear side connection ----------------------------------------------------------------------------------------- 10
III. Power supply -------------------------------------------------------------------------------------------------- 11
IV. USB Hub -------------------------------------------------------------------------------------------------------- 11
V. For your safety------------------------------------------------------------------------------------------------ 11
VI. Support timing chart----------------------------------------------------------------------------------------- 11
VII. Resistive Touch Panel -------------------- ------------------------------------------------------------------- 11
VIII. Mechanical dimension-------------------------------------------------------------------------------------- 12
IX. EMC Warning Statement ---------------------------------------------------------------------------------- 12
X. Product General Specification---------------------------------------------------------------------------- 13

3
I. Introduction:
P150TR is a color TFT LCD monitor, with compact and ecological design.
P150TR is an USB input Monitor with EETI controlled resistive touch screen and USB Hub
Features
-15 inch diagonal screen with native display resolution 1024 * 768.
-5 wires resistive touch panel (only touch screen models, (only P150TR)
-USB 2.0 Hub
-Fully Glossy surface throughout monitor’s appearance.
-No ventilation hole design.
-Cable management down routing through the mounting stand
-Light weight, only 2650 g physically.
Unpack the monitor
-Put the monitor on a clean surface; make sure the bo in upright position.
-Remove packing materials from inside of bo .
Check accessory
Please make sure the entire accessory is included:
AC-DC Power
Adaptor
USB cable User Guide & Driver CD

4
II. Installation:
Installing the DisplayLink USB Graphics Software (for Windows OS)
Install Displaylink Driver: Insert CD, Double click CD, the Installation menu shown as below.

5
Click Installation The Displaylink software end user Licence agreement shown as below:
Click I Accept, the Displaylink Core Software installs
Displaylink USB Graphic software installation will complete without notification.
Note 1: On some computers you may need to reboot before you can use your Displaylink enabled
device
Note 2: For operating system other than Windows, please visit DisplayLink website:
http://www.displaylink.com/support/downloads.php

6
Install EETI Touch Driver (For Touch screen)
Screen display as below, please click Ne t.

7
Select the set up type, don’t tick the bo if PS2 interface is not required,
Click “Ne t>
.
RS232 interface driver installed is default, please click Ne t>

8
You can select to do Touch screen calibration after system boot up or not
Default setting is” None”
Select to use Multi-Monitor system, then press Ne t>

9
Choose destination location, default folder location shown as below.
Press Ne t>
As Figure shown below, please press Ne t> to complete installation

10
①
④
③
②
Control Buttons/Connectors
Rear side connection:
①: DC12V input
②: USB input from Host PC, Mini USB B type
③: Downstream port, USB A type
④: Downstream port, Mini USB B type
Power
ON/OFF
After USB driver is installed, connect monitor to PC via USB cable.
Press power key to turn on /turn off the display
Blue LED indicate power on
Up Press this key will increase screen brightness
Down Press this key will decrease screen brightness