Phoenix Contact FLM BK PB M12 DI 8 M12-EF User manual

AUTOMATION
UM EN
FLM BK PB M12 DI 8 M12-EF
User Manual
Diagnostic and firmware functions
of the FLM BK PB M12 DI 8 M12-EF bus coupler

Designation:
Revision:
This user manual is valid for
AUTOMATION
8097_en_00 PHOENIX CONTACT
2010-07-26
Diagnostic and firmware functions of the FLM BK PB M12 DI 8 M12-EF
bus coupler
UM EN FLM BK PB M12 DI 8 M12-EF
00
the FLM BK PB M12 DI 8 M12-EF bus coupler Order No.: 2773377
User Manual

UM EN FLM BK PB M12 DI 8 M12-EF
PHOENIX CONTACT 8097_en_00
Please observe the following notes
In order to ensure the safe use of the product described, you have to read and understand
this manual. The following notes provide information on how to use this manual.
User group of this manual
The use of products described in this manual is oriented exclusively to qualified electricians
or persons instructed by them, who are familiar with applicable standards and other
regulations regarding electrical engineering and, in particular, the relevant safety concepts.
Phoenix Contact accepts no liability for erroneous handling or damage to products from
Phoenix Contact or third-party products resulting from disregard of information contained in
this manual.
Explanation of symbols used and signal words
The following types of messages provide information about possible property damage and
general information concerning proper operation and ease-of-use.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death.
DANGER
This indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING
This indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
This indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTE
This symbol and the accompanying text alerts the reader to a situation which may cause
damage or malfunction to the device, either hardware or software, or surrounding
property.
This symbol and the accompanying text provides additional information to the reader. It is
also used as a reference to other sources of information (manuals, data sheets, literature)
on the subject matter, product, etc.

UM EN FLM BK PB M12 DI 8 M12-EF
8097_en_00 PHOENIX CONTACT
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical
documentation and the products described in the technical documentation at its own
discretion and without giving prior notice, insofar as this is reasonable for the user. The
same applies to any technical changes that serve the purpose of technical progress.
The receipt of technical documentation (in particular data sheets, installation instructions,
manuals, etc.) does not constitute any further duty on the part of Phoenix Contact to furnish
information on alterations to products and/or technical documentation. Any other
agreement shall only apply if expressly confirmed in writing by Phoenix Contact. Please
note that the supplied documentation is product-specific documentation only and that you
are responsible for checking the suitability and intended use of the products in your specific
application, in particular with regard to observing the applicable standards and regulations.
Although Phoenix Contact makes every effort to ensure that the information content is
accurate, up-to-date, and state-of-the-art, technical inaccuracies and/or printing errors in
the information cannot be ruled out. Phoenix Contact does not offer any guarantees as to
the reliability, accuracy or completeness of the information. All information made available
in the technical data is supplied without any accompanying guarantee, whether expressly
mentioned, implied or tacitly assumed. This information does not include any guarantees
regarding quality, does not describe any fair marketable quality, and does not make any
claims as to quality guarantees or guarantees regarding the suitability for a special purpose.
Phoenix Contact accepts no liability or responsibility for errors or omissions in the content
of the technical documentation (in particular data sheets, installation instructions, manuals,
etc.).
The aforementioned limitations of liability and exemptions from liability do not apply, in so
far as liability must be assumed, e.g., according to product liability law, in cases of
premeditation, gross negligence, on account of loss of life, physical injury or damage to
health or on account of the violation of important contractual obligations. Claims for
damages for the violation of important contractual obligations are, however, limited to
contract-typical, predictable damages, provided there is no premeditation or gross
negligence, or that liability is assumed on account of loss of life, physical injury or damage
to health. This ruling does not imply a change in the burden of proof to the detriment of the
user.

UM EN FLM BK PB M12 DI 8 M12-EF
PHOENIX CONTACT 8097_en_00
Statement of legal authority
This manual, including all illustrations contained herein, is copyright protected. Use of this
manual by any third party is forbidden. Reproduction, translation, and public disclosure, as
well as electronic and photographic archiving or alteration requires the express written
consent of Phoenix Contact. Violators are liable for damages.
Phoenix Contact reserves all rights in the case of patent award or listing of a registered
design. Third-party products are always named without reference to patent rights. The
existence of such rights shall not be excluded.
How to contact us
Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be
found on the Internet at:
www.phoenixcontact.com.
Make sure you always use the latest documentation.
It can be downloaded at:
www.phoenixcontact.net/catalog.
Subsidiaries If there are any problems that cannot be solved using the documentation, please contact
your Phoenix Contact subsidiary.
Subsidiary contact information is available at www.phoenixcontact.com.
Published by .
Should you have any suggestions or recommendations for improvement of the contents and
layout of our manuals, please send your comments to
[email protected].
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
Germany
Phone +49 - (0) 52 35 - 3-00
Fax +49 - (0) 52 35 - 3-4 12 00
PHOENIX CONTACT
P.O. Box 4100
Harrisburg, PA 17111-0100
USA
Phone [phone]

8097_en_00 PHOENIX CONTACT i
Table of Contents
1 The Fieldline Modular Bus Coupler for PROFIBUS .................................................................1-1
2 Diagnostics .............................................................................................................................2-1
2.1 Activating/deactivating the diagnostic formats....................................................2-1
2.1.1 Diagnostics in the FLM BK PB M12 DI 8 M12-EF format ....................2-2
2.1.2 Status PDU diagnostic format .............................................................2-8
2.1.3 ID-specific diagnostic format ...............................................................2-9
2.2 Local diagnostic indicators ...............................................................................2-10
3 Acyclic Communication (DP/V1 and PCP) ..............................................................................3-1
3.1 Acyclic Communication via C1 Master ...............................................................3-1
3.2 Acyclic Communication via C2 Master ...............................................................3-1
3.3 PCP Communication Basics...............................................................................3-2
3.4 Acyclic Communication in DP/V1 Mode .............................................................3-4
3.4.1 The Communication Mechanism ........................................................3-4
3.4.2 Examples ............................................................................................3-7
3.5 Acyclic Communication in DP/V0 Mode via Process Data................................3-13
3.5.1 Mechanism for Transmission in the Process Data ............................3-13
3.5.2 Examples of VC1 Services ................................................................3-18
4 Dynamic Configuration ............................................................................................................4-1
4.1 Empty Spaces ....................................................................................................4-1
4.2 Principle of the Dynamic Configuration...............................................................4-3
4.3 Startup................................................................................................................4-5
4.3.1 Planning Configuration ........................................................................4-5
4.3.2 Options for Specifying the Active Configuration ..................................4-6
4.3.3 Specification of the Active Configuration via DP/V0 ............................4-7
4.3.4 Specification of the Active Configuration via DP/V1 ..........................4-10
4.3.5 Summary ..........................................................................................4-11
5 IO-Link ....................................................................................................................................5-1
A Appendix ................................................................................................................................ A-1
A 1 Error Codes for PCP Communication ................................................................ A-1
A 2 Error Codes for DP/V1 and VC1 Communication .............................................. A-3
A 3 Format of the Parameter Telegram.................................................................... A-4
B Object dictionaries .................................................................................................................. B-1
B 1 Slot 0 ................................................................................................................. B-1
B 2 Slot 1 ................................................................................................................. B-8
B 3 Slots 2 to 16....................................................................................................... B-8

UM EN FLM BK PB M12 DI 8 M12-EF
ii PHOENIX CONTACT 8097_en_00

The Fieldline Modular Bus Coupler for PROFIBUS
8097_en_00 PHOENIX CONTACT 1-1
1 The Fieldline Modular Bus Coupler for PROFIBUS
The bus coupler connects a Fieldline modular station to PROFIBUS-DP and is also used to
acquire digital signals.
16 devices can be connected in any position to an existing PROFIBUS-DP system using the
bus coupler.
The PROFIBUS bus coupler can be ordered using Order No. 2773377.
Figure 1-1 Fieldline Modular bus coupler for PROFIBUS
Features – Connection to PROFIBUS-DP using M12 connectors (B-encoded)
– Opens the Fieldline modular local bus using M12 connectors (B-encoded)
– Length local bus max. 20 m
– Data transmission speed max. 12 Mbps (automatic detection)
– Device description using GSD file
– Dynamic configuration and empty spaces
– Supported PROFIBUS addresses 1 to 126
– Up to 16 PCP devices can be connected
–I& M functions
– Connection of digital sensors using M12 connectors
– Flexible voltage supply concept
– LED diagnostic and status indicators for bus operation and voltage supply
– Short-circuit and overload protection of the sensor supply
– Channel-specific diagnostics for different I/O devices
– IP65/IP67 protection
– IO-Link-Call (firmware 2.0 or later)
7008A001

UM EN FLM BK PB M12 DI 8 M12-EF
1-2 PHOENIX CONTACT 8097_en_00
For additional information about the bus coupler, please refer to the following documents:
Data sheet: DB EN FLM BK PB M12 DI 8 M12-EF
Handbücher: FLS FLM SYS INST UM E und FLS FLM PB SYS PRO UM E
They can be downloaded at www.phoenixcontact.net/catalog.
Configuration and start-up with the Step7 SIMATIC Manager are described in detail in the
FLS FLM PB SYS PRO UM E.