Phonex Broadband WR300NQ User manual

1
Wireless Router
Quick Start Guide
Rev. 1.0a
Model WR300NQ

2
Step One: Hardware Connection
1. If you have xDSL Broadband internet access, connect your hardware as
shown in the following diagram:
2. If you have Residential Broadband internet access, connect your hardware
as shown in the following diagram:

3
After the hardware connections have been completed, check the status of the
LED Indicators using the following table:
LED
Indicator Description Normal Status
POWER Power Status
Indicator
Steady Light
SYS System status
Indicator
Steady Light or
Slow Flashing
WLAN Wireless Status
Indicator
Steady Light or
Slow Flashing
WPS Wi-Fi protected
status indicator
Steady Light or
Flashing When
Pairing
WAN Broadband
Network Status
Indicator
Steady Light or
Slow Flashing
1-4 LAN
Port
LAN (Local Area
Network)
indicator
Steady Light or
Slow Flashing
Note: If the LED indicator is not displaying a “Normal Status” as described in the table above, please check
the associated hardware and connections.
Safety Notice
¾Operating Position: The device should be placed on a flat horizontal surface, or secured safely to a
wall.
¾Operate equipment away from heat sources.
¾Provide good air ventilation.
¾Keep away from water and damp areas.
¾Disconnect power from the device during severe thunderstorms.
¾Use only the included AC power adapter.

4
Step Two: Set up the computer
Installation on a Windows 2000 or Windows XP system
1. Right click on “My Network Places” and choose “Properties”.
2. Right click on “local Area Connection” and choose “Properties”.

5
3. Double click on “Internet Protocol (TCP/IP)”
4. Choose “Obtain an IP address automatically”, then choose “obtain DNS
Server Address automatically”, click the “OK” button.

6
Installation on a Windows Vista or Windows 7 system
1. Click on “start”, then select “Control Panel”, then select “Network and Internet”,
and then you should see “local Area Connection”. Right click “Local Area
Connection”, and then choose “Properties”.
2. Double click on “Internet Protocol Version4 (TCP/IPv4)”.

7
3. Choose “Obtain an IP address automatically” then choose “Obtain DNS Server
Address automatically”, then click the “OK” button.
Step Three: Using the Setup Wizard
1. Open a web browser.
Note: The default wireless IP address for the wireless router is 192.168.1.1, the
default Subnet Mask is 255.255.255.0
2. Type “ http://192.168.1.1 ” in the Address field of your web browser and
press the “Enter” key. A User Name and Password dialog box will
appear. The default User Name is “admin” and the default password is
“admin”, enter the user name and password then click the “OK” button.

8
3. After a successful login, the router setting Wizard will appear, click the “Next”
button.

9
4. Determine which of the three listed ISP access methods is used by your
internet service provider.
5. Select the Internet Parameter choice, and click the “Next” button.
If you chose Static IP:
If your broadband internet service provider assigned you a fixed IP address,
enter the Server IP Address, Subnet Mask and DNS parameters provided by
your broadband internet service provider. C lick the “Next” button.
If you chose Dynamic IP:
If your broadband internet service provider delivers a dynamically assigned IP
address, the wireless router can automatically obtain the IP address from your
broadband internet service provider. C
lick the “Next” button.

10
If you chose ADSL Virtual dial-up:
If your broadband internet service provider delivers a PPPoE dial-up / virtual
dial-up service compatible with ADSL and Residential broadband Internet
access, type in the “Account“ name and “Password” provided by your
broadband internet service provider. C lick the “Next” button.
6. Set the wireless parameters:
SSID: Names the wireless router so it can be identified by devices that
access it. The name can contain letters and numbers.
Channel: Choose the wireless channel you wish to use.
Wireless Encryption: Choose the type of encryption you wish to use.
Wireless Password: Choose a password for your wireless network.
You will need to know the password to access your wireless router.
Click “Finished”, and Wait 30 seconds for the configuration to complete.