PhotoCentric Wash 15 User manual

2205 West Parkside Lane, Phoenix,
85027, AZ USA
[email protected]
UK USA
DISPOSAL INSTRUCTIONS
Do not throw this electronic device into the waste when
discarding. To minimize pollution and ensure utmost pro-
tection of the global environment, please recycle or return
to Photocentric for recycling.
Cambridge House, Oxney Road
Peterborough PE1 5YW UK.
[email protected]
www.photocentricgroup.com USER MANUAL
AND INSTALLATION
GUIDE

All cleaning tanks should be handled with care to
ensure maximum performance, please read, and
understand this user manual before using your
ultrasonic cleaner:
• Do not operate if the tank is less than 2/3 full.
• Ensure power is disconnected before attempting
toaddorremoveuid.
• Ifpouringuidaway,pourawayfromtheelectrical
socket on the rear and front control panel.
• Do not let items rest on the base of the bath,
always use the basket or provided bracket from
Photocentric.
• We do not advise using the heat function with
Photocentric Cleaner as this could have a
negativeeectonyourparts,theheatfunction
can be used with alternative cleaning agents i.e.,
soap and water.
• When submerging parts ensure uid is not
displaced out of the bath.
• Maximum running time for a single cycle is 30
minutes.
• Never drop an item onto the base of the bath.
• Never change the fuse for a higher rated one.
We recommend keeping your Photocentric ultraso-
nic cleaner away from the below conditions:
• High humidity
• Unpredictableuctuatingtemperatures,too hot
ortoocoldconditionscanaectthefunctionality
and lifespan of the machine
• Non-stable surfaces
• Corrosive gases
• Loose chemicals, oils, and water (not including
the cleaner currently being used)
• Where explosives or unstable chemicals are sto-
red
• Do not used the product if it is in an unstable
conditioni.e.,susceptibletoreorexplosion
Manufacturer
Photocentric Ltd
Cambridge House, Oxney Road
Peterborough, PE1 5YW, UK
Year of CE Marking: 2019
Certications:
CE Certied
WEEE approved
FCC approved
Thank you for purchasing the Photocentric ultrasonic
cleaner, please read all of this instruction manual to
ensure you are operating this machine correctly and
safely.
If there is any damage to the wire or machine, please do
not connect it to the power supply, instead contact the
Service and Support team:
European and Asia Pacic Customers
[email protected]
North and South American Customers
[email protected]
Contents
1. Safety Warnings
2. Photocentric Wash 15 at a glance
3. Unboxing & Installation
4. Ultrasonic Cleaning Principle
5. Product Operation- Cautions
6. Product Operation- Usage
7. Maintenance
1. Safety
warnings
WASH 1 5
Set ¼C
TEMP+TEMP-
ON/OFF
ON
TIME+TIME-
ON/OFF
Actual ¼C Minute Second
Do not use when empty
Minimum fill level 2/3
Caution hot liquid
Earth must be connected
ON
NO

2. Photocentric Wash
15 at a glance
The Wash 15 has been designed to remove all residual
resin from printed models.
3. Unboxing &
Installation
3a. Location Requirements
The placement of the Photocentric Wash 15 is
important for the safe running and for optimal
performance of the wash unit. Photocentric Wash 15
external dimensions are 400(l) x 350 (w) x 280 (h) mm.
It weighs 9.5kg. Consider enough space when
selecting a stable location for the Photocentric
Wash15unit.Ensurethatthereissucientroomto
access the wall outlet and power supply, space for
accessoriesandnally,theproximitytoanextraction
duct.
All operations involving uncured resin or printed parts
in the green state should be performed in a low-
light environment so that components have minimal
exposure to daylight. It is highly recommended that
red ambient lighting is used to prevent early curing.
Choose a location where the ambient temperature is
in the range of 18-28°C.
3b. Unboxing Photocentric
Wash 15
Photocentric Wash 15 is packed in a cardboard
enclosure inclusive of foam inserts above and below
the main unit. To unbox the unit, open the box from
the top. Remove the foam inserts covering the top of
the unit and use the side handles to lift carefully from
the box. Use safety gloves with a secure grip surface
to prevent slipping.
Remove internal packaging to access the accessories.
3c. Power Requirements
• Photocentric Wash 15 requires a mains power
supply with a voltage of 100-120VAC- 60Hz or
200-240VAC- 50Hz (depending on the unit).
• Wash 15 power consumption (only when
Ultrasonic is in use without the heating function)
is rated at 360W.
• Only connect Photocentric Wash 15 to the mains
socket using the power cable supplied into the
power port, and that the current draw of the items
connected to the mains does not exceed the
capacity of the fuse or breaker.
• Makesurethatthepowerisobeforeconnecting
or disconnecting the power cable.
1. Bracket: Holds the build platform when washing
parts on the platform.
2. Removable Basket (optional): Holds parts to
wash without the build platform.
3. Outer Lid: Limits resin cleaner evaporation and
keeps the potentially harmful fumes contained.
Keep the lid closed when not in use.
4. Wash Tank: Holds the resin cleaner to wash the
parts. Tank can hold a maximum of 15 litres of resin
cleaner.
5. Drain Plug: To remove the used saturated resin
cleaner after the parts have been cleaned.
6. Clip: Helps to robustly secure the drainpipe to the
drain plug.
MAIN FEATURES:
• Timer – Canbeturnedonoroandsetanywhere
from 1-30 minutes. To increase the process timer
by 1 minute press the up-arrow button. Hold the
up-arrow button to increase in 10-minute steps.
To decrease by 1 minute press the down arrow
button. Hold the down arrow button to decrease
in 10-minute steps.
•For cleaning of printed parts with Photocentric
resin cleaners, using the temperature settings is
not recommended.
4. Ultrasonic cleaning
principle
The Photocentric wash unit is an ultrasonic cleaner
for use in both industrial and domestic usage.
Made from high-quality SUS stainless steel plate,
the Photocentric wash unit oers a temperature
heating element and a strong ultrasonic power
output. Residue resin can be extremely hard to
remove by hand; however, it becomes easy with the
use of the Photocentric Wash unit and Photocentric
Cleaner. All 3D printed parts can be cleaned in the
ultrasonic process to remove resin residue, this can
be achieved to a ‘perfect’ condition with the use of
Photocentric Cleaner.
5. Product Operation
– Cautions
Please read and follow the guidelines provided whilst
operating this machine - if these are not adhered to,
they can cause damage to your machine and may
invalidate your warranty. Before starting the machine
ensure that:
• Allbuttonsandswitchesareturnedo
• Cleaner is present in the tank (2/3 minimum)
• No liquid has splashed on the electronic parts of
the machine
• Theheating processis notstartedunlesssu-
cient liquid is placed in the machine
• The power supply is earthed and grounded
• The machine is not moved whilst in use
5
4
3
1
2
6

6. Product Operation
Instructions
The following instructions will ensure safe and
correct use of your Photocentric Wash unit:
• Step 1: Placeultrasoniccleaneronaat,stable
surface.
• Step 2: Add Photocentric Cleaner to a level
whereitwillnotoverow–approximately
2/3 full. If using the bracket provided,
remove the basket from the wash tank.
• Step 3: Plug in the cleaner and switch
on via the switch at the rear of the unit if
present, otherwise at the wall socket. (If no
buttons are pressed, after eight hours your
ultrasonic cleaner will go into power save
mode. To restore power, press any buttor.
• Step 4: Place your printed part or platform
tted to the bracket into the ultrasonic
cleaner. If your Photocentric Wash 15 is
completely full of liquid with the printed
parts immersed, then place the lid back in
your cleaner to prevent spillage.
• Step 5: Set the timer to the relevant
settings. If you are using Photocentric
Cleaner check TDS for recommended
wash time. Once set, press the on button
and this will enable the ultrasonic function.
• Step 6: To end the cleaning process, press
the corresponding key again; if nothing
is pressed the ultrasonic will stop when
the timer reaches 00:00 - if the heating
function is in use the heater will switch on
and o to maintain the uid at the target
temperature.
PHOTOCENTRIC RESIN CLEANER
SKU. RESIN-CLEANER 5LTR
CLEANER
Resins
5 L e
5060151503022
PHOTOCENTRIC RESIN CLEANER
SKU. RESIN-CLEANER 5LTR
CLEANER
Resins
5 L e
5060151503022
WASH 1 5
Set ¼C
TEMP+TEMP-
ON/OFF
ON
TIME+TIME-
ON/OFF
Actual ¼C Minute Second
Do not use when empty
Minimumfill level 2/3
Caution hot liquid
Earth must be connected
ON
NO
05:00
05:00

7. Maintenance
• Empty the liquid out of your Photocentric wash
unit after either a month of usage, or when it
is no longer cleaning your parts properly, the
specicoptionwilldependonhowfrequently
the machine is in use. To empty the liquid,
disconnect all power supplies and carefully
place the out valve (as seen in the below
diagram) over a bottle or container. Once
positioned turn the valve to release all the
Photocentric Cleaner from inside your wash
unit. This bottle or container needs to then be
sealed and disposed of following your local
regulations and guidelines and Cleaner Safety
Data Sheet.
• Do not cover the vents of the wash unit.
• Do not operate the machine without
Photocentric cleaner inside.
• It is advised to operate the machine with the lid
securely wash unit.
• Do not use alcohol, gasoline, or ammable
solutions. Doing so could cause a re or
explosion and will void the warranty of your
machine.
• Do not use mineral acids as these could
damage your tank.
• Do not touch the tank or cleaning solution
during use.
• Do not allow temperatures to exceed 70
degrees centigrade.
• Donotplaceyourngersorhandsintothetank
whilst the cleaner is operating. Doing so may
cause discomfort and possible skin irritation.
• Avoid skin contact with solutions and provide
adequate ventilation if necessary.
• Do not use solutions containing chlorine
bleach.
• Use a low power air compressor to clean dust
from the control system regularly.
• Once a month on emptying the cleaner out
of your wash unit we also advise cleaning the
inside of the ultrasonic, please do this whilst
the machine is turned o, empty and not
connected to the power.
• To prevent damage to the wash unit do not
replace the cleaning solution more frequently
than is needed.