Pioneer LEXUS RX330 User manual

ORDER NO.
CRT3348
PUB. NO. CRT3348
AUDIO SYSTEM
POWER AMPLIFIER
Manufactured for TOYOTA
by PIONEER CORPORATION
VEHICLE DESTINATION PRODUCED AFTER TOYOTA PART No. ID No. PIONEER MODEL No.
LEXUS RX330 U.S.A., CANADA August 2004 86100-0E020 GM-8347ZT/X1R/E
EUROPE
RX330
Service
Manual

2
1234
1234
F
E
D
C
B
A
GM-8347ZT/X1R/E
-This service manual should be used together with the manual(s) listed below.
For the parts numbers, adjustments, etc. which are not shown in this manual, refer to the following
manual(s).
Model No. Order No. Mech. Module Remarks
GM-8337ZT/E CRT3014
-Supplementary model is identical to the original except for the addition of following items.
Part No.
Description GM-8347ZT/X1R/E
Protector (x1/4) HHP2716
Packing Assy (x1/4) HHX1764
Contain Box (x1/4) HHL5083
SAFETY INFORMATION
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65

3
5678
F
E
D
C
B
A
5678
GM-8347ZT/X1R/E
ELECTRICAL PARTS LIST(Page 23)
Amp Assy Part No.
Symbol and Description GM-8337ZT/E GM-8347ZT/X1R/E
R521,522,523,524 RS1/16S0R0J RS1/16S100J
R719 RS1/16S221J RS1/16S1000D
R725,726,928 RS1/16S0R0J RS1/16S100J
C706 CKSRYB473K25 CKSRYB393K25
DSP Assy Part No.
Symbol and Description GM-8337ZT/E GM-8347ZT/X1R/E
IC101 IC PD5767A PEG010A
L942,943 Inductor LCTA2R2J2520 LCTAW2R2J2520
R135 RS1/16S102J RS1/16S3301D
R317,318,337,338,357,358,361 RS1/16S0R0J RS1/16S100J
R362,363,364,365,366,459,460 RS1/16S0R0J RS1/16S100J
R479,480 RS1/16S0R0J RS1/16S100J
EXTERIOR(Page 4)
-EXTERIOR SECTION PARTS LIST Part No.
Mark No. Symbol and Description GM-8337ZT/E GM-8347ZT/X1R/E
4 Chassis CNA2538 HNA2538
5 Case CNB2776 HNB2776
6 Shield Case CNC9891 HNC9891
7 Bracket CND1244 HND1761
8 Bracket CND1245 HND1762
9 Insulator CNM7683 HNM7683
10 Seal CNM8060 HNM8060
11 Heat Sink CNR1651 HNR1651
12 Amp Unit CWM8303 CWM9574(Amp Assy)
14 Screw (M3x6) CBA1393 HBA1393
20 Holder CNC9893 HNC9893
21 Holder CNC9894 HNC9894
22 Bracket CND1109 HND1109
24 DSP Unit CWM8304 CWM9575(DSP Assy)
27 ASL Unit CWM8305 HWM8882
EXPLODED VIEWS AND PARTS LIST

4
1234
1234
F
E
D
C
B
A
GM-8347ZT/X1R/E
FX-MG8237ZT-02/ES (Pio AMP Model)
FX-MG8337ZT-02/ES(M/L AMP Model)
GGD1402
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
Bullet connector
(To DC Regulated Power Supply)
H/U
12P20P
20P
20P
24P 20P
20P
20P
24P
GGD1317
AUI+AUI-
FL+FL-
AMP
EMV
6P 28P26P
28P26P
8P18P
18P 8P
NAVI ECU
10P
10P
GM-8347ZT/X1R/E or M/L AMP
*M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different from pioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal array is different).
Therefore, when the head unit of the M/L AMP system is
repaired, pioneer AMP system is used.
*Pio:Pioneer
*M/L:Mark Levinson
Connection Diagram EMV NAVI SYSTEM(AMP: Pio & M/L)
ADJUSTMENT

5
5678
F
E
D
C
B
A
5678
GM-8347ZT/X1R/E
FX-MG8237ZT-02/ES (Pio AMP Model)
FX-MG8337ZT-02/ES (M/L AMP Model)
*Pio:Pioneer
*M/L:Mark Levinson
Connection Diagram STD SYSTEM(AMP:Pio & M/L)
GGD1317
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
H/U
20P 12P20P 24P 20P
20P
20P 24P
AMP
M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different from pioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal array is different).
Therefore, when the head unit ofthe M/L AMP system is
repaired, pioneer AMP system is used.
GM-8347ZT/X1R/E or M/L AMP

6
1234
1234
F
E
D
C
B
A
GM-8347ZT/X1R/E
GGD1402
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
Bullet connector
(To DC Regulated Power Supply)
H/U
12P20P
20P
20P
24P 20P
20P
20P
24P
GGD1317
AUI+AUI -
FL+FL-
AMP
*Pio:Pioneer
*M/L:Mark Levinson
Connection Diagram EMV NAVI SYSTEM(AMP:Pio & M/L)
EMV
6P 28P26P
28P26P
8P18P
18P 8P
NAVI ECU
10P
10P
GM-8347ZT/X1R/E or M/L AMP
*M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different frompioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal arrayisdsdifferent).
Therefore,when the head unitof the M/L AMP system is
repaired, pioneer AMP system is used.
FX-MG9647ZT/EW(M/L AMP Model)
FX-MG9747ZT/EW(M/L AMP Model)
FX-MG9847ZT/EW(Pio AMP Model)
FX-MG9947ZT/EW(Pio AMP Model)
FX-MG8347ZT/EW(M/L AMP Model)
FX-MG8447ZT/EW(M/L AMP Model)
FX-MG8547ZT/EW(Pio AMP Model)
FX-MG8647ZT/EW(Pio AMP Model)

7
5678
F
E
D
C
B
A
5678
GM-8347ZT/X1R/E
*Pio:Pioneer
*M/L:Mark Levinson
Connection Diagram STD SYSTEM(AMP:Pio & M/L)
GGD1317
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
H/U
20P 12P20P 24P 20P
20P
20P 24P
AMP
M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different from pioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal array is different).
Therefore, when the head unit of the M/L AMP system is
repaired, pioneer AMP system is used.
GM-8347ZT/X1R/E or M/L AMP
FX-MG9647ZT/EW(M/L AMP Model )
FX-MG9747ZT/EW(M/L AMP Model )
FX-MG9847ZT/EW(Pio AMP Model)
FX-MG9947ZT/EW(Pio AMP Model)
FX-MG8347ZT/EW(M/L AMP Model )
FX-MG8447ZT/EW(M/L AMP Model )
FX-MG8547ZT/EW(Pio AMP Model)
FX-MG8647ZT/EW(Pio AMP Model)

8
1234
1234
F
E
D
C
B
A
GM-8347ZT/X1R/E
GGD1402
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
Bullet connector
(To DC Regulated Power Supply)
H/U
12P20P
20P
20P
24P 20P
20P
20P
24P
GGD1317
AUI+AUI-
FL+FL-
AMP
*Pio:Pioneer
*M/L:Mark Levinson
Connection Diagram EMV NAVI SYSTEM(AMP:Pio & M/L)
EMV
6P 28P26P
28P26P
8P18P
18P 8P
NAVI ECU
10P
10P
GM-8347ZT/X1R/E or M/L AMP
FX-MG8947ZT/UC(Pio AMP Model)
FX-MG8847ZT/UC(M/L AMP Model)
FX-M9447ZT/UC(Pio AMP Model)
*M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different from pioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal array is different).
Therefore, when the head unit of the M/L AMP system is
repaired, pioneer AMP system is used.

9
5678
F
E
D
C
B
A
5678
GM-8347ZT/X1R/E
RSE ECU
24P
GGD1401
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
Bullet connector
(To DC Regulated Power Supply)
FX-MG8947ZT/UC(Pio AMP Model)
FX-MG8847ZT/UC(M/L AMP Model)
FX-M9447ZT/UC(Pio AMP Model)
GM-8347ZT/X1R/E or M/L AMP
H/U EMV
8P
12P20P 6P 28P
8P18P
8P
18P 8P
6P12P20P
20P
24P 20P
20P
20P
24P
GGD1317
AUI +AUI-
FL+FL-
AMP
VTR Adapter
NAVI ECU
32P
20P
20P
32P
Rear Disp & SDVD
32P
GGD1319
*M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different from pioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal array is different).
Therefore, when the head unit of the M/L AMP system is
repaired, pioneer AMP system is used.
*Pio:Pioneer
*M/L:Mark Levinson
26P
28P26P
Connection Diagram EMV/RSE NAVI SYSTEM(AMP:Pio & M/L)
10P
10P
24P 10P
10P
32P

10
1234
1234
F
E
D
C
B
A
GM-8347ZT/X1R/E
RSE ECU
24P
GGD1401
Bullet connector
(To DC Regulated Power Supply)
Bullet connector
SP Line
Bullet connector
(To DC Regulated Power Supply)
FX-MG8947ZT/UC(Pio AMP Model)
FX-MG8847ZT/UC(M/L AMP Model)
FX-M9447ZT/UC(Pio AMP Model)
GM-8347ZT/X1R/E or M/L AMP
H/U
8P
12P20P
8P
6P
12P20P
20P
24P 20P
20P
20P
24P
GGD1317
AUI+AUI-
AMP
VTR Adapter
32P
20P
20P
32P
Rear Disp & SDVD
32P
GGD1319
*M/L AMP SYSTEM cannot use GGD1317.
Because, external connector is different from pioneer AMP and
M/L AMP(PIO:24P-20P,M/L:25P-16P).
Moreover, GGD1240 which is a previous jig cannot be used
(Because the signal array is different).
Therefore, when the head unit of the M/L AMP system is
repaired, pioneer AMP system is used.
28P26P
24P
10P
10P
32P
Non-connected
for RSE
18P 8P 10P
for EMVfor EMVfor EMV
*Pio:Pioneer
*M/L:Mark Levinson
Connection Diagram RSE SYSTEM(AMP:Pio & M/L)
for EMV for EMV for EMV
Non-
connected Non- connected Non- connected
Non-
connected
Non-
connected
Non-
connected