Pioneer ND-BC010 User manual
P1c,n'8cer
ND-BC010
Owner's Manual
UNIVERSAL
REAR-VIEW
CAMERA
i,
INCLUDED PARTS / HARNESS DETAILS
_'
ACC. SIGNAL (+12 V DC)
VIDEO OUTPUT
GROUND
POWERI VIDEO CABLE
REAR/FRONT
SETTING
LOOP
(WHITE WIRES)
TO
CAMERA
UNIT
CAMERA WITH MOUNTING
BRACKET
t
SPECIFICATIONS
••
··t7
.'
Image view
Sensortype
TV
Line resolution
Resolution (Pixel)
Min. illumination
Viewing angle
Video system
Voltage & max. current
Waterproof
Operation temperature
Storage temperature
Compliance statement
Selectable (Mirror Image
as
default)
High quality CMOS
960
TV
lines equivalent
470,000 pixels
0.1
Lux~0.01 Lux
170°
NTSC (Color)
9 V DC to 16 V DC, 100
mA
IP67 / IP68
-30°C ~ +70°C
-30°C ~ +85°C
FMVSS
111
Pi
INFORMATION TO THE USER >
Alteration
or
modifications carried out without appropriate authorization may invalidate the user's
right to operate the equipment.
FEDERAL COMMUNICATIONS COMMISSION SUPPLIER'S DECLARATION OF CONFORMITY
Product Name:
Model Number:
Responsible Party Name:
Universal Rear-view Camera
ND-BC010
PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 970
W.
190th STREET, SUITE 360, TORRANCE CA90502,
USA
Phone: (800) 421-1404
URL: http://www.pioneerelectronics.com
CAN ICES-3 B/NMB-3 B
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bukyo-ku, Tokyo 113-0021, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O.
BOX 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404 © 2023 PIONEER CORPORATION
.~-
c-
lMPORTANT SAFEGUARDS
':_;
.
•
i:-
A
• Installation and wiring
of
this product require specialist skill and experience.
To
assure your safety, please request a specialist technician to install the unit.
•
Do
not attempt to heatthe surface
of
the camera lens
or
camera lens itselfwith a lighterand so on when
they have become frozen. This can cause a malfunction.
• This product is a rear view camera forchecking the view
at
the rear
of
a vehicle. A rear view camera is a
camera that provides symmetrical images in the same way as rear and side view mirrors.
• This product is designed to supplement the driver's rear view, butthe camera images
do
not show all
dangers and obstacles. Be sure to look behind you when reversing to confirm the view.
• This product features a wide-angle lens, so the nearview is wide and the far view is narrow, which
may
create a false sense
of
distance. Be sure to look behind you when reversing to confirm the view.
• Do notwash your vehicle with an automatic carwash
or
high-pressure water as itmay result in water
entering the camera
or
the camera falling off.
• Check camera stand installation before driving.
Are the screws loose? Is the camera stand firmly secured?
(If
the rearview camera comes loose while you are driving
it
may
cause an accident.)
• This product by itselfdoes not display guidelines.
• System is designed for+12 V DC systems only.
• Be cautious when mounting camera and wiring nearfuel tank.
,,
CONNECTION & ELECTRICAL INFORMATION
,.;
.
.,,
• This unit is for vehicles with a 12-volt battery
(DC/=)
and negative grounding.
(Before installing it in a recreational vehicle, truck,
or
bus, checkthe battery voltage.)
*1~
~
¥-.....
Blacklead wire (Ground} =
0 /
"-...,/'<-
Metal part
of
the vehicle body
*1
Not
supplied for this unit
•
•
To
avoid short-circuits in the electrical system, be sure to disconnect the battery cable before installation.
• Referto the owner's manual for details on connecting the other units, then make connections correctly.
• Secure the wiring with cable clamps
or
adhesive tape around them where they lie against metal parts.
Route
and
secure allwiring so
it
cannottouch
any
movingparts, such as the
gear
shift, parking brake
and
seatrails.
Do
notroute wiring in places that
get
hot, such as
near
the heateroutlet.
If
the insulation
of
the
wiring melts
or
gets torn, there is a danger
of
the the wiring short-circuiting to the vehicle body.
• Do not shorten any leads.
• Neverfeed powerto other equipment
by
cutting the insulation
of
the power supply lead
of
the unit and
tapping into the lead. The current capacity
of
the lead will be exceeded causing over heating.
• Please request specialist technician for the replacement
of
the fuse with correct specification.
•
To
minimize noise locate the
TV
antenna cable, radio antenna cable and
RCA
power supply cable as far
away from each otheras possible.
• Connection to a
TV
with an RCAvideo input is possible, but confirm whether the
TV
you use has a reverse
gearconnection function.
•
If
this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition
switch, the red lead
of
the unit should be connected
to
a terminal coupled with ignition ON/OFF
operations.
If
this is not done, the vehicle battery may be drained when you are awayfrom the vehicle
forseveral hours.
ACC
pos;tion
No
ACC
position
• Cords for this product and those forother products may be different colors even
if
they have the same
function. When connecting this productto another product, refer to the supplied manuals
of
both products
and connect cords that have the same function.
~
INSTALLATION PROCEDURE
~
CAMERAINSTALLATION POSITION OPTIONS
The camera mounting base can be positioned eithervertically
or
horizontally.
(Install the rearview camera so that the A mark is located on the top
of
camera)
TOP
BOTTOM
..
Forward
direction Forward
direction
Note: Disassembly
of
the camera mounting bracket may be necessary depending on mounting.
(Be sure
not
to hide
any
part
of
the characters on the licence plate when attaching the camera)-
REAR-VIEW/
FRONT-VIEW SETTING
For a front-view camera installation, connect the two white wires provided for this purpose.
THINK TWICE, WORK ONCE!
• Install the unit nearthe center
of
the vehicle.
• Locate in the position you want to install the rear view camera.
•Adjust the angle
of
the rear view camera, and install so thatthe camera body doesn'ttouch the vehicle.
(Avoid touching
any
sheetmetal
or
glass section from the vehicle)
• Before making a final installation
of
the unit, temporarily connect the wiring to confirm that the connections
are correct and the system works properly.
Install
on
the centerpart
Make
sure
it
doesn'ttouch the wiper
MOUNTING BASE INSTALLATION
1- Clean the surface to which the rear view camera is to be installed.
(Use a cloth
or
otheritem to wipe oil, wax, dust
and
only
otherdirt from installation surface)
2-
Peel offthe sheet on the back
of
the camera stand and stick it on.
3- Press the camera stand with your fingers to stick itto the installation surface.
(Touching the adhesive surface
or
sticking the unit
on
a second time reduces adhesive power)
CABLE AND WIRE LEADS ROUTING
• Make sure none
of
the leads are trapped between this unit and the surrounding metalwork
or
fittings.
(To protectthe wire from a break
and
short circuit to ground)
• Before drilling any mounting holes always check behind where you want to drill the holes.
(Do
not
drill into the gasline, brake line, electrical wiring
or
otherimportantparts)
• Always use protective rubber grommetwhen wire
or
cable must pass through sheet metal.
(To protectthe wire from a break
and
shortcircuitto ground,
and
to avoidanyliquid infiltration)
•
If
the wiring
of
this unit is located undera front seat, make sure it does not obstruct seat movement.
(Route al/ leads
and
cable carefully aroundthe
any
mechanismsso they do notgetcaught
or
pinched)
1- Route the wire from the camera unit inside the vehicle. When possible,
we
suggestyou use the existing
rubber sleeves to avoid any drilling. The cable is long enough to allowyou to bring the connector into
the rear quarter panel
of
the vehicle.
2- Connectthe camera to the power/video cable and route the cable inside the vehicle from the rear
of
the
vehicle to the display unit and theACC. +12 V DC power source.
3- Connectthe video output RCAconnector to the dedicated input
of
the display unit.
4- ConnecttheACC. +12 V
DC
wire
of
the camera (Red wire) as mentioned previously in this document.
5- Connectthe Ground
of
the camera (Black wire) to the vehicle body by using the appropriate mechanical
link like a metal screw.
CAMERAADJUSTMENTS :)·
1- Park the vehicle
in
a safe place with a typical view to refer to.
2- Secure the vehicle's parking brake.
3-Activate the camera and display unit by turning on theACC. in the vehicle.
4-
Manually activate the reversing camera input
of
the display.
• Most display units have a dedicated menu for it.
• Ifrequired, temporarily connect the display input activation wire to a
+12 V DC source to simulate information from the vehicle's reverse lights.
5- Carefully adjust the position
of
the camera for an optimal view.
• Camera view must be centered horizontally
• Camera view must be centered vertically
-,~.
•Any upward alignment, may cause unwanted reflections with the sun.
Bumper
or
rear
edge
of
car
6- Lock the camera angle using the hex
key.
IMPORTANT NOTES & INSTALLATION TIPS
••
·1i
• Use onlythe parts included with the unit to ensure proper installation.
(The use
of
unauthorizedparts can cause malfunctions)
• Consult with your nearest dealer ifinstallation requires:
• The drilling
of
holes,
•Any other modifications
of
the vehicle.
~
-~
• Install the unitwhere it does not get
in
the driver's way and cannot injure the passenger.
(If
there is a sudden stop, like an emergencystop)
•
If
this unit is installed in the passengercompartment, anchor it securely.
(So
it
does
not
break free while the vehicle
is
moving,
and
cause injury
or
an accident)
• Install so that
it
does not obstructthe rear field
of
view.
• Install so that
it
does not protrude from the side
of
the vehicle.
• Do not perform installation in rain
or
fog.
• When humidity is high, dry the surface to which the unitis to be attached before installing.
(Moisture
on
the attachmentsurface reduces adhesive strength which
may
lead
to the unitcoming off)
• Ifthe temperature
of
the attachment surface
is
low, warm it with a hair dryer
of
other means before
installing the camera base to improve adhesive strength.
• Do not attach the camera stand to areas on the vehicle body treated with fluorocarbon resin, or glass.
(This
may
resultin the rear view camera falling off)
• During the 24-hour period after-installing:
• Do not apply water to the unit.
• Do not expose the unit
to
rain.
• Do not subject the camera to unnecessaryforce.
FCC COMPLIANCE STATEMENT
~:~:
'!Ii..•(,.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15
of
the FCC Rules.These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference
to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If
this equipment does cause harmful interference to radio
or
television reception, which can be
determined by turning the equipment offand on, the user is encouraged to try to correct the interference by
one
or
more
of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consultthe dealer
or
an experienced radio/TV technician for help. •
This device complies with part 15
of
the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Table of contents
Other Pioneer Digital Camera manuals
