Pioneer DVR-R100 User manual

4
En
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model
properly. After you have finished reading the instructions, put them away in a safe place for
future reference. K015 En
The Generation of Acoustical Noise Is Less Than 70dB.
(ISO7779/DIN45635)
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filed
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
or moisture.
D3-4-2-1-3_A_En
CAUTION
This product is a class 1 laser product, but this
product contains a laser diode higher than Class 1.
To ensure continued safety, do not remove any covers
or attempt to gain access to the inside of the product.
Refer all servicing to qualified personnel.
The following caution label appears on your unit.
Location: on top of the cover D3-4-2-1-8_A_En
CLASS 1 LASER PRODUCT
LASER KLASSE 1
IMPORTANT NOTICE – RECORD THE MODEL NUMBER AND SERIAL NUMBERS OF THIS EQUIPMENT BELOW.
THE NUMBERS ARE ON THE REAR.
MODEL NO.
SERIAL NO.
KEEP THESE NUMBERS FOR FUTURE USE. D1-4-2-6-2_En
DVR-R100, DVR-610
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to lead, a chemical known to
the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
D36-P4_En
Wash hands after handling
is a trademark of DVD Format/Logo Licensing Corporation.

FEATURES
• Write Speed (*CAV, **ZCLV)
DVD-R 1X, 2X, 6X, 8X*, 12X*, 16X*
DVD-R (DL) 2X, 4X, 6X, 8X
DVD-RW 1X, 2X, 4X, 6X
DVD+R 2.4X, 4X, 6X, 8X*, 12X*, 16X*
DVD+R (DL) 2.4X, 4X, 6X, 8X
DVD+RW 2.4X, 4X, 6X, 8X
CD-R 4X, 10X, 16X, 24X*, 32X*, 40X*
CD-RW 4X, 10X, 16X, 20X**, 24X**, 32X**
• Maximum Read Speed
DVD-ROM (single) 16X DVD-ROM (DL) 12X
DVD-R 16X DVD+R 16X
DVD-R (DL) 8X DVD+R (DL) 8X
DVD-RW 6X DVD+RW 8X
DVD-RAM 2X
CD-ROM, CD-R 40X
CD-RW 32X
• Buffer Memory Size 2 MBytes (Write/Read)
• IDE Data Transfer Mode PIO Mode 4 / Multi Word DMA
Mode 2 / Ultra DMA Mode 4
• 5.25” Half-Height built-in type
• Stereo Audio Output
• LCD Tilt Servo Mechanism
• Horizontal/Vertical orientation available
• Low vibration mechanism by DRA system
Disc Format (Read/Write)
• DVD single layer/dual layer / 120mm / 80mm disc
• DVD-R (when writing, use only 650nm for General use media)
• DVD-R
• Dual Layer DVD-R
• DVD-RW
• DVD+R
• Double Layer DVD+R
• DVD+RW
• DVD-RAM (non-cartridge, Version 2.0, Version 2.1) (Read only)
• CD-ROM Mode 1
• CD-ROM XA Mode 2 (form 1, form 2)
• Photo CD (single and multiple session)
• CD-DA
• CD-Extra (CD PLUS)
• Video CD
• CD Text
• CD-R
• CD-RW / High Speed CD-RW / Ultra Speed CD-RW
Note:
• A specific application program is needed to write the formats listed above.
• Supported media required for specific DVD and CD writing speeds.
• When writing to DVD at 12X or 16X, use Pioneer-tested media. For media brand information, refer to
Pioneer website: www.pioneerelectronics.com
6
En

8
En
INTERFACE
REAR VIEW
Pin Name Function
1 L Left channel audio output.
2 G Ground.
3 G Ground.
4 R Right channel audio output.
Pin Name Function
1 MA on The drive is used in master mode.
2 SL on The drive is used in slave mode.
3 CS on Using Cable Select function.
4 Reserved.
5 Reserved.
5Audio Output
This connector outputsanalog audio.
This connector is compatible with `Molex 70553`, choose a suitable connection cable.
Pin Name Function
1 +12 Power supply input for DC +12 V.
2 G Ground.
3 G Ground.
4 +5 Power supply input for DC +5 V.
6Device Configuration Jumper
Switch becomes ON when a jumper is added.
Make sure the power of the drive is OFF before changing the jumper setting.
Pin # 1 is ON when shipped from the factory.
7Host IDE Interface
This is a 40 pin I/O connector according to the ATA specifications.
8DC Input
5 6 7
ANLOG AUDIO
CABLE SELECT
SLAVE
MASTER
5V G G 12V
ALS
M
40
39
2
1
SC IDE INTERFACE
DC INPUT
8

9
English
En
1Turn OFF the computer's power and remove the power cord from the wall outlet
before removing the front panel cover.
2Remove the blank panel from the front of the 5.25" bay slot.
3Install the fixing slide rails on the drive. (When slide rails are required, please contact
the store where the drive was purchased.)
4Insert the drive into the slot.
5When anchoring is required, please refer to the computer's instruction manual.
÷Please use screws measuring 5mm (3/16 in.) or less for mounting. Using
longer screws may damage the drive.
÷When the mounting screws are loose, the vibrations from a spinning disc may
generate ripping noise. To prevent this noise, tighten the screws.
INSTALLATION