Planet MFB-Series User manual

PLANET Fiber Transceiver
MFB-Series / MGB-Series / MTB-Series
User’s Manual

- 2 -
Trademarks
Copyright ©PLANET Technology Corp. 2014
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and
applications, and makes no warranty and representation, either implied or expressed, with respect to the
quality, performance, merchantability, or tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a
commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may
be contained in this User’s Manual. PLANET makes no commitment to update or keep current the

- 3 -
information in this User’s Manual, and reserves the right to make improvements to this User’s Manual
and/or to the products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete, we would appreciate
your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

- 4 -
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Revision
User's Manual for PLANET SFP / SFP+ / XFP Mini-GBIC Transceiver
For Models: MFB-SERIES / MGB-SERIES / MTB-SERIES
Rev: 1.9 (June 2014)
Part No: 2010-AG0220-007

- 5 -
Table of Contents
1. Overview ....................................................................................................................................................6
2. Checklist..................................................................................................................................................... 7
3. Introduction and Model List....................................................................................................................... 8
3-1 The MFB-Series Mini-GBIC Transceiver Module List ......................................................................8
3-2 The MGB-Series Mini-GBIC Transceiver Module List....................................................................12
3-3 The MTB-Series Mini-GBIC Transceiver Module List ....................................................................17
4. Installing SFP / SFP+ / XFP Transceiver Module..................................................................................20
4-1 Install the SFP / SFP+ Mini-GBIC Transceiver Module .................................................................20
4-2 Install the 10GBase-LR / SR XFP Fiber Optic Module MTB-XSR / MTB-XLR............................ 21
4-3 Remove the SFP / SFP+ / XFP Transceiver Module .................................................................... 22
Appendix A.....................................................................................................................................................23
A.1 Fiber Optic Cable Connection Parameters.....................................................................................23
Safety Notice .................................................................................................................................................24

- 6 -
1. Overview
Thank you for purchasing PLANET SFP / SFP+ / XFP Mini-GBIC Transceiver which includes the
Ethernet module of the MFB / MGB and MTB families.
The MFB family Fast Ethernet SFP module can be installed into PLANET Switch products with
100Base-FX SFP interface. The distance can be extended from 2km (Multi-mode, LC) up to 120
kilometers (Single-mode, LC).
The MGB family Gigabit Ethernet SFP module can be installed into PLANET Switch products with
1000Base-SX/LX SFP interface. The distance can be extended from 100 meters (TP), 550 meters
(Multi-mode, LC), up to 120 kilometers (Single-mode, LC).
The MTB family 10G Ethernet SFP+ / XFP module can be installed into PLANET products with 10G
SFP+ / XFP interface. The distance can be extended from 300 meters (Multi-mode, LC), up to 10
kilometers (Single-mode, LC).

- 7 -
2. Checklist
Your SFP / SFP+ / XFP Package should contain the following items:
zThe SFP / SFP+ / XFP Transceiver Module x 1
zThe User’s Manual x 1
If any item is missing or damaged, please consult the dealer from whom you purchased your SFP /
SFP+ / XFP Mini-GBIC Ethernet transceiver module.

- 8 -
3. Introduction and Model List
3-1 The MFB-Series Mini-GBIC Transceiver Module List
Fast Ethernet Transceiver (100Base-X SFP)
Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
MFB-FX 100 LC Multi-Mode 2km 1310nm 0 ~ 60 ºC
MFB-F20 100 LC Single Mode 20km 1310nm 0 ~ 60 ºC
MFB-F40 100 LC Single Mode 40km 1310nm 0 ~ 60 ºC
MFB-F60 100 LC Single Mode 60km 1310nm 0 ~ 60 ºC
MFB-F120 100 LC Single Mode 120km 1550nm 0 ~ 60 ºC
MFB-TFX 100 LC Multi-Mode 2km 1310nm -40 ~ 75 ºC
MFB-TF20 100 LC Single Mode 20km 1550nm -40 ~ 75 ºC

- 9 -
Fast Ethernet Transceiver (100Base-BX, Single Fiber Bi-Directional SFP)
Model Speed
(Mbps)
Connector
Interface Fiber Mode Distance Wavelength (TX) Wavelength (RX) Operating Temp.
MFB-FA20 100 WDM (LC) Single Mode 20km 1310nm 1550nm 0 ~ 60 ºC
MFB-FB20 100 WDM (LC) Single Mode 20km 1550nm 1310nm 0 ~ 60 ºC
MFB-TFA20 100 WDM (LC) Single Mode 20km 1310nm 1550nm -40~75 ºC
MFB-TFB20 100 WDM (LC) Single Mode 20km 1550nm 1310nm -40~75 ºC
MFB-TFA40 100 WDM (LC) Single Mode 40km 1310nm 1550nm -40~75 ºC
MFB-TFB40 100 WDM (LC) Single Mode 40km 1550nm 1310nm -40~75 ºC

- 10 -
1. When shorter distance of single mode fiber cables is used, you might need to insert
an in-line optical attenuator in the link to avoid overloading the receiver: Follow the
I-TUT G652 document to imitate the fiber cable length.
2. The attenuation coefficient that mentioned in the following chapters is for reference
only.
Attenuation coefcient
Wavelength region Typical link value
1260nm-1360nm 0.5 dB/km
1530nm-1565nm 0.4 dB/km

- 11 -
SFP Model
Physical
Fiber Cable Length “n” km
MFB-F20
MFB-TF20 MFB-F40 MFB-F60 MFB-F120
10 < n < 20 2 dB 4-6 dB 8-10 dB 25-27 dB
20 < n < 40 -- 2-4 dB 6-8 dB 23-25 dB
40 < n < 60 -- -- 2-4 dB 18-20 dB
SFP Model
Physical
Fiber Cable Length “n” km
MFB-TFA10
MFB-TFB10
MFB-FA20 / MFB-FB20
MFB-TFA20 / MFB-TFB20
MFB-TFA40
MFB-TFB40
10 < n < 20 -- 2 dB 4-6 dB
20 < n < 40 -- -- 2-4 dB
40 < n < 60 -- -- --

- 12 -
3-2 The MGB-Series Mini-GBIC Transceiver Module List
Gigabit Ethernet Transceiver (1000Base-X SFP)
Model Speed (Mbps) Connector Interface Fiber Mode Distance Wavelength (nm) Operating
Temp.
MGB-GT 1000 Copper -- 100m -- 0 ~ 60 ºC
MGB-SX 1000 LC Multi-Mode 550m 850nm 0 ~ 60 ºC
MGB-SX2 1000 LC Multi-Mode 2km 1310nm 0 ~ 60 ºC
MGB-LX 1000 LC Single Mode 10km 1310nm 0 ~ 60 ºC
MGB-L30 1000 LC Single Mode 30km 1310nm 0 ~ 60 ºC
MGB-L40 1000 LC Single Mode 40km 1550nm 0 ~ 60 ºC
MGB-L50 1000 LC Single Mode 50km 1550nm 0 ~ 60 ºC

- 13 -
MGB-L70 1000 LC Single Mode 70km 1550nm 0 ~ 60 ºC
MGB-L120 1000 LC Single Mode 120km 1550nm 0 ~ 60 ºC
MGB-TSX 1000 LC Multi-Mode 550m 850nm -40 ~ 75 ºC
MGB-TLX 1000 LC Single Mode 10km 1310nm -40 ~ 75 ºC
MGB-TL30 1000 LC Single Mode 30km 1310nm -40 ~ 75 ºC
MGB-TL70 1000 LC Single Mode 70km 1550nm -40 ~ 75 ºC
Gigabit Ethernet Transceiver (1000Base-BX, Single Fiber Bi-Directional SFP)
Model Speed
(Mbps)
Connector
Interface Fiber Mode Distance Wavelength (TX)
Wavelength
(RX)
Operating
Temp.
MGB-LA10 1000 WDM (LC) Single Mode 10km 1310nm 1550nm 0 ~ 60 ºC

- 14 -
MGB-LB10 1000 WDM (LC) Single Mode 10km 1550nm 1310nm 0 ~ 60 ºC
MGB-LA20 1000 WDM (LC) Single Mode 20km 1310nm 1550nm 0 ~ 60 ºC
MGB-LB20 1000 WDM (LC) Single Mode 20km 1550nm 1310nm 0 ~ 60 ºC
MGB-LA40 1000 WDM (LC) Single Mode 40km 1310nm 1550nm 0 ~ 60 ºC
MGB-LB40 1000 WDM (LC) Single Mode 40km 1550nm 1310nm 0 ~ 60 ºC
MGB-LA60 1000 WDM (LC) Single Mode 60km 1310nm 1550nm 0 ~ 60 ºC
MGB-LB60 1000 WDM (LC) Single Mode 60km 1550nm 1310nm 0 ~ 60 ºC
MGB-TLA10 1000 WDM (LC) Single Mode 10km 1310nm 1550nm -40 ~ 75 ºC
MGB-TLB10 1000 WDM (LC) Single Mode 10km 1550nm 1310nm -40 ~ 75 ºC
MGB-TLA20 1000 WDM (LC) Single Mode 20km 1310nm 1550nm -40 ~ 75 ºC
MGB-TLB20 1000 WDM (LC) Single Mode 20km 1550nm 1310nm -40 ~ 75 ºC

- 15 -
MGB-TLA40 1000 WDM (LC) Single Mode 40km 1310nm 1550nm -40 ~ 75 ºC
MGB-TLB40 1000 WDM (LC) Single Mode 40km 1550nm 1310nm -40 ~ 75 ºC
MGB-TLA60 1000 WDM (LC) Single Mode 60km 1310nm 1550nm -40 ~ 75 ºC
MGB-TLB60 1000 WDM (LC) Single Mode 60km 1550nm 1310nm -40 ~ 75 ºC
SFP Model
Physical
Fiber Cable Length “n” km
MGB-LX MGB-L30 MGB-L40 MGB-L70 MGB-L120
10 < n < 20 -- 2-4 dB 5-7 dB 13-15 dB 25-27 dB
20 < n < 40 -- 2 dB 3-5 dB 10-12 dB 23-25 dB
40 < n < 60 -- -- 5-7 dB 18-20 dB

- 16 -
SFP Model
Physical
Fiber Cable Length “n” km
MGB-TLX MGB-TL30 MGB-TL70
10 < n < 20 -- 2-4 dB 13-15 dB
20 < n < 40 -- 2 dB 10-12 dB
40 < n < 60 -- -- 5-7 dB
SFP Model
Physical Fiber
Cable Length “n” km
MGB-LA10
MGB-LB10
MGB-TLA10
MGB-TLB10
MGB-LA20
MGB-LB20
MGB-TLA20
MGB-TLB20
MGB-LA40
MGB-LB40
MGB-TLA40
MGB-TLB40
MGB-LA60
MGB-LB60
MGB-TLA60
MGB-TLB60
10 < n < 20 -- 2 dB 4-6 dB 8-10 dB
20 < n < 40 -- -- 2-4 dB 6-8 dB
40 < n < 60 -- -- -- 2-4 dB

- 17 -
3-3 The MTB-Series Mini-GBIC Transceiver Module List
10Gbps XFP (10G Ethernet/10GBase)
Model Speed (Mbps) Connector
Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
MTB-XSR 10G LC Multi-Mode Up to 300m 850nm 0 ~ 60 ºC
MFB-XLR 10G LC Single Mode 10km 1310nm 0 ~ 60 ºC
10Gbps SFP+ (10G Ethernet/10GBase)
Model Speed (Mbps) Connector
Interface Fiber Mode Distance Wavelength (nm) Operating Temp.
MTB-SR 10G LC Multi-Mode Up to 300m 850nm 0 ~ 60 ºC
MFB-LR 10G LC Single Mode 10km 1310nm 0 ~ 60 ºC

- 18 -
10Gigabit Ethernet Transceiver (10GBase-BX, Single Fiber Bi-Directional SFP)
Model Speed
(Mbps)
Connector
Interface Fiber Mode Distance Wavelength (TX)
Wavelength
(RX)
Operating
Temp.
MTB-LA20
MTB-LB20
10G WDM (LC) Single Mode 20km 1270nm 1330nm 0 ~ 60 ºC
10G WDM (LC) Single Mode 20km 1330nm 1270nm 0 ~ 60 ºC
MTB-LA40
MTB-LB40
10G WDM (LC) Single Mode 40km 1270nm 1330nm 0 ~ 60 ºC
10G WDM (LC) Single Mode 40km 1330nm 1270nm 0 ~ 60 ºC
MTB-LA60
MTB-LB60
10G WDM (LC) Single Mode 60km 1270nm 1330nm 0 ~ 60 ºC
10G WDM (LC) Single Mode 60km 1330nm 1270nm 0 ~ 60 ºC

- 19 -
SFP Model
Physical
Fiber Cable Length “n” km
MTB-LA20
MTB-LB20
MTB-LA40
MTB-LB40
MTB-LA60
MTB-LB60
10 < n < 20 2 dB 4-6 dB 8-10 dB
20 < n < 40 -- 2-4 dB 6-8 dB
40 < n < 60 -- -- 2-4 dB

- 20 -
4. Installing SFP / SFP+ / XFP Transceiver Module
4-1 Install the SFP / SFP+ Mini-GBIC Transceiver Module
Please follow these steps to install the SFP / SFP+ Mini-GBIC module:
1. Power on the Switch and place the Switch on a
at surface. Install the new SFP / SFP+ Mini-GBIC
module by inserting it into the slot and sliding it in
until it stops (See Figure 1). Press it rmly until you
hear the module snap into place. Never force, twist
or bend the SFP / SFP+ Mini-GBIC module. The
SFP / SFP+ Mini-GBIC module slides in smoothly
and the Switch will automatically detect the new
module.
SFP/SFP+Transceiver
Figure 1: Insert the SFP/SFP+ Mini-GBIC Module
2. After the TP / Fiber connection is made successfully, check the LEDs to verify that if there is a link
and a proper connection at the port.
Please refer to the user’s manual for more about the Switch or module’s management.