Planex MZK-NAS01SG User manual

Multi Media Network Attached
Storage 1 Bay / Storage 2 Bay
MZK-NAS01SG / MZK-NAS02SG

Foreword
Explanation of the signals
In order to let you set up and use this product correctly, please pay attention when reading or
browsing the manual as you see these signals listed below.
Warning/ Danger
Users should read the explanation carefully and understand it completely, otherwise
users might be in danger or even be injured.
Caution/ Be Careful
Remind users to be careful when setting up the product and to avoid damaging the
product or its system programs.
Seeking for service or searching for an agent or a distributor
Thank you for purchasing products from Planex Communications Inc. If you have any
operational problems while configuring or setting up the product, you may contact with our
Customer Service Department or ask the agent or the distributor from which you bought
the product for help. Moreover, during warranty, if you find any defect or breakdown of the
product, you may bring the product, assembly, and its warranty card to our company or to
where you bought the product to ask for repair.
★Every product has different warranty period and contract; please refer to our
company for further information or consult the agent or the distributor.
Planex Communications Inc.
Support Phone：[phone] (Singapore)
[phone]/6173/6174 (Taiwan)
Customer Service E-Mail：[email protected]
Contact Us
Tel：[phone]
Fax：[phone]
Agents & Distributors：http://www.planex.net/where/index.htm

Trademarks:
To maintain compliance with FCC RF exposure compliance requirements, please avoid direct
contact to the transmitting antenna during transmitting.

Contents
Foreword
Chapter1 Introduction of MZK-NAS01SG/MZK-NAS02SG . .1
1. Contents of Package . . . . . . . . . . . . . . . . . . .2
Chapter 2 Function Introduction and Quick Install Guide . .3
1. Product Functions . . . . . . . . . . . . . . . . . . . . . .3
2. Installation Guide . . . . . . . . . . . . . . . . . . . . . .7
Chapter 3 Web Configuration and RAID .............17
1. WEB Configuration . . . . . . . . . . . . . . . . . . . .17
2. Building RAID (For MZK-NAS02SG Only) . . . .19
Chapter 4 Common Functions ....................23
1.AddingUsers.........................23
2.AddingGroups.......................25
3.FileServer ...........................27
4.BTDownload.........................33
5. WEB/FTP Download. . . . . . . . . . . . . . . . . . . .37
Chapter 5 Detail Function ........................41
1.Language...........................41
2.Status...............................42
MZK-NAS01SG/MZK-NAS02SG

3.Basic ...............................43
3.1. Time Zone . . . . . . . . . . . . . . . . . . . . . . . .43
3.2. Password. . . . . . . . . . . . . . . . . . . . . . . . .44
4.Network.............................45
5. File/FTP Server . . . . . . . . . . . . . . . . . . . . . . . .46
5.1. Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.2. Groups . . . . . . . . . . . . . . . . . . . . . . . . . .48
5.3. File Server . . . . . . . . . . . . . . . . . . . . . . . . 50
5.4. FTP Server . . . . . . . . . . . . . . . . . . . . . . . . 55
6.BitTorrent............................59
7. Web/FTP Download . . . . . . . . . . . . . . . . . . .64
8.iTunesServer.........................66
9.MediaServer.........................69
10.Tools...............................71
10.1. Storage Tools (For MZK-NAS02SG) . . . . 71
10.2. Storage Status . . . . . . . . . . . . . . . . . . . 73
10.3. USB Copy . . . . . . . . . . . . . . . . . . . . . . .73
10.4. Configuration Tools . . . . . . . . . . . . . . . 74
10.5. Firmware Update . . . . . . . . . . . . . . . . . 76
10.6. Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .78
MZK-NAS01SG/MZK-NAS02SG Contents

MZK-NAS01SG/MZK-NAS02SG

1Introduction to MZK-NAS01SG /
MZK-NAS02SG
Thank you for purchasing MZK-NAS01SG/MZK-NAS02SG Network
Attached Storage (NAS) server. This Storage device can let you share your
files with users all around your network easily. All you have to do is insert
your SATA hard disks into MZK-NAS01SG/MZK-NAS02SG, connect the
LAN port with a LAN cable (RJ45 connectors), some basic settings, and
you’re ready to share your files on your LAN network. MZK-NAS01SG/
MZK-NAS02SG provide the perfect file sharing/storage solution for
medium size business or Small Office/Home Office (SOHO).
MZK-NAS01SG/MZK-NAS02SG have a built-in Web server, thus you can
access its settings through Web browsers, such as IE, Netscape, Firefox,
and so on. You can set up and configure the settings easily and completely
and enjoy the convenience instantly.
MZK-NAS01SG/MZK-NAS02SG have many features, which includes:
●Support two internal SATA hard disk drives (MZK-NAS02SG only)
●Provide two USB ports for USB mass storage devices connecting
●Sharing your files via FTP or Network Neighborhood
●Sharing your multimedia files to DLNA compliant media adapters, such
as Xbox 360 and Sony PS3
●Built-in iTunes Server allows you to share your music with all the users
on your local Network.
●Download functions allow you to download files through FTP, World
Wide Web (WWW), and BitTorrent.
●High file transfer rate (more than 100Mbps)
1
1
Chapter1 Introduction to MZK-NAS01SG/MZK-NAS02SG

1
2
MZK-NAS01SG/MZK-NAS02SG
1. Contents of Package
After purchasing MZK-NAS01SG/MZK-NAS02SG Network Attached
Storage (NAS) server form a distributor or an agency, please open the
package and check that all the components listed below are included. If
there is any item missing or damaged, please contact with the distributor or
the agency at once.
MZK-NAS01SG
●MZK-NAS01SG
●CD-ROM (User’s Manual)
●AC Adapter
●AC Power Cable
●Screw (x4)
●Rubber Foot (x4)
●UTP cable
●Warranty Card
MZK-NAS02SG
●MZK-NAS02SG
●CD-ROM (User’s Manual)
●AC Adapter
●AC Power Cable
●Screw (x8)
●Rubber Foot (x4)
●UTP cable
●Warranty Card
If plug the AC adapter which includes in the product package
into a socket with different voltage power supply, it will cause
damage and that is not included in warranty.

2
3
Chapter2 Function Introduction and Quick Install Guide
2Function Introduction and Quick
Install Guide
Front Panel
LED Status Meaning
Power On/Flashing
After turning MZK-NAS01SG/MZK-NAS02SG, the
Power LED will be on. If MZK-NAS01SG/MZK-
NAS02SG is shutting down or restoring to the default
settings, the Power LED will be flashing.
LAN 1/2 On/Off
LAN LED will be on when the LAN port is
connected, and will be off when the LAN port is
disconnected.
USB 1 / 2 On/Flashing
When connecting with a USB storage device (with
FAT32, FAT16, and EXT2 format), the LED will be on.
The LED will be flashing when copying files
from the USB device to MZK-NAS01SG/MZK-
NAS02SG.
HDD 1/2 On/Flashing
When internal SATA hard disk is connected and
formatted by MZK-NAS01SG/MZK-NAS02SG, the
HDD LED will be on accordingly.
●LEDs and Meanings:
1. Product Functions
MZK-NAS01SG MZK-NAS02SG

2
4
MZK-NAS01SG/MZK-NAS02SG
●Release Button:
The Release button has three functions: 1. Unplug the external USB
mass storage connected to the USB 1 port. 2. Shut down MZK-
NAS01SG/MZK-NAS02SG. 3. Reset the configuration of MZK-
NAS01SG/MZK-NAS02SG to factory default settings (when pressing
Copy button at the same time).
◆Unplug the external USB storage device: Press and hold Release
button for 2 seconds, MZK-NAS01SG/MZK-NAS02SG will beep
for 0.5 second to hint that your command is detected. Release the
Release button immediately, and unplug the external USB storage
device plugged in USB1 port safely. If you want to unplug the external
USB device connected to the USB 2 port, please doing so by using
MZK-NAS01SG/MZK-NAS02SG configuration webpage. (Tools ->
Storage Status -> Unplug)
◆Shut down MZK-NAS01SG/MZK-NAS02SG: Press and hold
Release button for more than 5 seconds to start shutting down the
storage server. Ignore the first short beeping sound. The Power
LED will keep flashing, and you will hear a long beeping sound.
When the Power LED goes off, MZK-NAS01SG/MZK-NAS02SG
are completely shut down. You can now switch off the power by
switching the Power switch on the back panel of MZK-NAS01SG
/MZK-NAS02SG.
◆Restore the configuration of MZK-NAS01SG/MZK-NAS02SG to
factory default settings: If you want to reset the configurations of
MZK-NAS01SG/MZK-NAS02SG to factory default settings, you
should press and hold BOTH the Release button and the Copy buttons
at the same time for more than 5 seconds until you hear a long beep.
The Power LED will keep flashing during the restore process. After the
restore is complete, MZK-NAS02SG will restart automatically.

2
5
Chapter2 Function Introduction and Quick Install Guide
●Copy Button:
The Copy button has two functions: 1. Copy the content of one external
USB storage device to another attached storage device. 2. Reset the
configuration of MZK-NAS01SG/MZK-NAS02SG to factory default
settings (when pressing Release button at the same time).
◆Copy USB mass storage device: Press and hold the Copy button
for 2 seconds, MZK-NAS01SG/MZK-NAS02SG will beep for 0.5
second to hint that your command is detected. Release the Copy
button immediately if you want to copy the content of one external
USB mass storage device to another attached storage device. During
the process of copy, the LED of corresponding USB port will flash
slowly. When the LED of corresponding USB port stops flashing and
is lit steady, the copy job is finished. If any error occurs during the
process of copy, the LED of corresponding USB port will flash very
fast. The default source storage is USB 1. You can change the source
storage by USB Copy settings in MZK-NAS02SG’s Web user
interface.
◆Restore the configuration of MZK-NAS01SG/MZK-NAS02SG to
factory default settings: If you want to reset the configurations of
MZK-NAS01SG/MZK-NAS02SG to factory default settings, you
should press and hold BOTH the Release button and the Copy
buttons at the same time for more than 5 seconds until you hear a
long beep. The Power LED will keep flashing during the restore
process. After the restore is complete, MZK-NAS02SG will restart
automatically.
●USB 1: USB 1 port allows you to share your files stored in the USB
mass storage device plugged in.

2
6
MZK-NAS01SG/MZK-NAS02SG
Back Panel
Ports Function
USB 2
USB 2 port allows you to share your files stored in the USB mass
storage device plugged in. Also, USB 2 ports allows you to format
the attached USB storage device
LAN 1/2
Use standard LAN cables (RJ45 connectors) to connect MZK-
NAS01SG/MZK-NAS02SG with your hubs/switches, or one LAN
port of your router, etc.
DC Plug the power cord into this port and the other side of the adaptor
should be plugged into the socket.
Button Function Usage
Power
On/Off
Turning On/
Off MZK-
NAS01SG/
MZK-
NAS02SG
Please do not turn off the power while MZK-
NAS01SG/MZK-NAS02SG is running. This will
cause data saving errors and MZK-NAS01SG/MZK-
NAS02SG may not be able to work properly. Before
switching off the power, please press Release button
for more than 5 seconds and shut down MZK-
NAS01SG/MZK-NAS02SG first.
MZK-NAS01SG MZK-NAS02SG

2
7
Chapter2 Function Introduction and Quick Install Guide
2. Installation Guide
Please follow this step-by-step guide and install your MZK-NAS01SG/
MZK-NAS02SG.
1.Please push the button of the hard disk drawer in the back panel of
MZK-NAS01SG/MZK-NAS02SG, releasing the drawer lock.
2.Pull out the hard disk drawer gently.

2
8
MZK-NAS01SG/MZK-NAS02SG
3.Place your SATA hard disk on the hard disk drawer as shown in the
picture.
Note: When you put the SATA hard disk on the hard disk drawer,
make sure the screw holes of the hard disk match those of the
drawer.
4.Fix your SATA hard disk tightly in the hard disk drawer with the
screws provided in the MZK-NAS01SG/MZK-NAS02SG package.

2
9
Chapter2 Function Introduction and Quick Install Guide
5.After securing the SATA hard disk tightly to the hard disk drawer, slide
the drawer back to MZK-NAS01SG/MZK-NAS02SG gently as shown
in the picture.
6.Push the leverage of the hard disk drawer, sliding the drawer further
into MZK-NAS01SG/MZK-NAS02SG until you hear a slight “click
”sound.
Note: Please make sure the hard disk drawer is installed correctly as
shown in the picture.

2
10
MZK-NAS01SG/MZK-NAS02SG
7.Plug in the RJ45 cord to any LAN port on the back panel of
MZK-NAS01SG/MZK-NAS02SG.
8.Plug in the other side of the RJ45 cord to the LAN port of your PC or
router.

2
11
Chapter2 Function Introduction and Quick Install Guide
9.P l u g i n t h e p o w e r a d a p t e r p r o v i d e d i n M Z K-N A S01S G/
MZK-NAS02SG package into the DC port, and the other side in the
power socket as shown in the picture.
Plug the AC Adapter which comes with MZK-NAS01SG/MZK-
NAS02SG in a different voltage power supply will cause damage
on MZK-NAS01SG/MZK-NAS02SG, and it is not included in
warranty.

2
12
MZK-NAS01SG/MZK-NAS02SG
10. Turning on MZK-NAS01SG/MZK-NAS02SG by pressing the Power
On/OFF switch in the back panel.
11. If your computer is having trouble connecting to MZK-NAS01SG/
MZK-NAS02SG and the configuration webpage isn’t displayed
properly, please follow the steps down below and configurate your
computer.
●Click “Start”button (it should be located at lower-left corner of your
computer), and then click “Control Panel”.
Before turning your MZK-NAS01SG/MZK-NAS02SG on, make
sure that your MZK-NAS01SG/MZK-NAS02SG is connected to
the router properly. If you fail to do so, your computer may not be
able to connect to MZK-NAS01SG/MZK-NAS02SG.

2
13
Chapter2 Function Introduction and Quick Install Guide
●Double-click “Network and Internet Connections”, and then click
“Network Connections”.