Platinum Hot Tubs Legend User manual

The Legend Owners Manual
English and French Versions

Table Of Contents
Page
Introduction i
Important Safety Instructions 1-2
Choosing A Location 2
Power Requirements 3-4
Control System Diagram 5
Wiring Diagram 6
Specifications & Drawing 7
Audio Connection Diagram 8
Electrical Wiring Instructions 9
Start-Up Instructions 10-11
Operation Instructions 12-14
Display Messages 15
Spa Care and Maintenance 16-17
Water Quality and Maintenance 18-21
Spa Care and Maintenance Record 22
Spa Accessories 23
Warranty 24

i
Introduction
Your choice of spa indicates that you are devoted to excellence. The manufacturer appreciates your patronage and
takes pride in the tradition of quality spas that our company represents.
In order to get the most out of your spa, we strongly suggest that you take time to read through this manual before you
hook up and operate your spa. This will acquaint you with the operating features; procedures, maintenance, and
safety procedures, ensuring an enjoyable experience right from the start. The manufacturer has tried to anticipate all
of your needs and desires however, if you need any additional information, feel free to call the manufacturer.
WARNING!! This manual was written to ensure the proper use and installation of your spa. Any modifications to the
procedures outlined in this manual may result in your warranty being voided. Please take the time to read this manual
to avoid any unnecessary problems with your brand new spa and equipment.
THIS MANUAL AND ITS CONTENTS ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALTHOUGH WE HAVE
PREPARED THIS MANUAL TO BE AS ACCURATE AND PRECISE AS POSSIBLE, WE WILL NOT BE LIABLE
FOR LOSS, INJURY OR DAMAGES CAUSED BY IMPROPER INSTALLATION OR USE OF SPA (IMPROPER OR
OTHERWISE).
LOCATION OF SPA SERIAL NUMBER
Date Purchased:
DateInstalled:
DealerName:
SpaSerialNumber:
www.platinumhottubs.com
MANUFACTURE RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE.
SPA DATA PLATE LOCATED ON CABINET FRAME LOWER BOTTOM OF
ACCESS DOOR
1 – 8 6 6 – 4 8 6 – 1 3 6 5
Remember to fill out your Registration Form on your new spa. See
warranty page attachment in back of owner’s manual.

1
IMPORTANT SAFETY INSTRUCTIONS
When installing your spa and using this equipment, basic safety precautions should always be followed. For your
safety and the safety of others it is vital that the following be observed:
•READ AND FOLLOW ALL INSTRUCTIONS! The following instructions are required by UL 1563 standard to
be printed as a condition of their listing this product. They contain important safety information we strongly
urge you to read and apply.
•DANGER - TO REDUCE THE RISK OF INJURY: Do not permit children to use spa unless they are closely
supervised at all times.
WARINING SIGN MUST BE POSTED
The WARNING sign (RED) above is packed with your new Platinum Spa. This sign must be posted in a prominent place
in close proximity to the spa installation site immediately upon completion of spa installation.
•WARNING SIGN - It is extremely important that this sign be permanently placed in clear view of any persons
using the spa. Occasional spa users may not be aware of some of the dangers hot water poses to pregnant
women, small children, and people under the influence of alcohol. If you did not receive a warning sign or your
sign has become damaged, please contact the manufacturer.
•DANGER - A wire connector is provided on this unit to connect a minimum No. 6 AWG (10 mm2) solid copper
conductor between unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or
conduit, if that item is located within 5 feet (1.5m) of the unit.
•DANGER - RISK OF ACCIDENTAL DROWNING: Extreme caution must be exercised at all times, to prevent
unauthorized access by children. To avoid accidents, ensure that children cannot use spa unless they are
supervised at all times. Cover spa and use safety locks to prevent accidents.
•DANGER - TO REDUCE THE RISK OF INJURY: The suction fittings in the spa are sized to match the specific
water flow created by the pump/pumps. Should the need arise to replace the suction fittings or the
pump/pumps, be sure that the flow rates are compatible.
•DANGER - RISK OF ELECTRICAL SHOCK: Install at least 5 feet (1.5m) from all metal surfaces. As an
alternative, a spa may be installed within 5 feet (1.5m) of metal surfaces if each metal surface is permanently
connected by a minimum No. 6 AWG solid copper conductor to the wire connector on the terminal box that is
proved for this purpose. Do not permit any electrical appliance, such as a light, telephone, radio or television
within 5 feet (1.5m) of the spa, unless factory installed.
•Position spa to provide proper drainage and accessibility of electrical compartments.
•For floor recessed spas, install to permit access for servicing from above or below floor.
•NEVER USE AN EXTENSION CORD!
•Consideration should be taken for water splash out. Water can ruin wood floors and some finishes.
•DO NOT use a wall switch, ground fault circuit interrupter, circuit breaker, fuse, or plugging and unplugging the
spa as a means of turning on or off your spa for normal everyday use.
•DO NOT block access door.
•Set the spa on a firm level (flat) surface. DO NOT set spa on blocks as structural damage may occur to spa.
•WARNING - To reduce the risk of injury the water in a spa should never exceed 40.0° C (104.0° F). Water
temperatures between 38.0° C (100.0° F) and 40.0° C (104.0° F) are considered safe for a healthy adult. Lower
water temperatures are recommended for young children and when spa use exceeds 10 minutes.

2
IMPORTANT SAFETY INSTRUCTIONS
•Since excessive water temperatures have a high potential for causing fetal damage during early pregnancy,
pregnant or possibly pregnant women should limit water temperatures to 38.0° C (100.0° F). Before entering a
spa, the user should test the water temperature with an accurate thermometer. The tolerances of water
temperature-regulating devices vary. The use of alcohol, drugs, or medication before or during spa use may
lead to unconsciousness with the possibility of drowning. Persons suffering from obesity, medical history or
heart disease, low/high blood pressure, circulatory system problems, or diabetes, should consult a physician
before using a spa. Persons using medication should consult a physician before using a spa because some
medications induce drowsiness while others may affect heart rate, blood pressure and circulation.
•Your spa is equipped with audio.
Caution - Risk of Electric Shock.
Do not leave audio compartment door and cover open.
Caution - Risk of Electric Shock
Replace audio components only with identical components.
Warning - Prevent Electrocution
Do not connect any auxiliary components. For example, cable, additional speakers, headphones, etc. to the
system.
HYPERTHERMIA
Prolonged immersion in hot water may induce hyperthermia. A description of the causes, symptoms, and effects of
hyperthermia are as follows:
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body
temperature of 98.60° F (37.0° C). The symptoms of hyperthermia include drowsiness, lethargy, and an increase in the
internal temperature of the body. The effects of hyperthermia include:
•Unawareness of impending hazard;
•Failure to perceive heat;
•Failure to recognize the need to exit spa;
•Physical inability to exit spa;
•Fetal damage in pregnant women; and
•Unconsciousness and danger of drowning.
SAVE THESE INSTRUCTIONS
IMPORTANT: Because of the combined weight of the spa, water and users, it is extremely important that the base upon
which the spa rests be smooth, flat, level and capable of uniformly supporting this weight, without shifting or settling, for
the entire time the spa is in place. If the spa is placed on a surface which does not meet these requirements, damage to
the skirt and/or the spa shell may result. Damage caused by improper support is not covered under warranty. It is the
responsibility of the spa owner to assure the integrity of the support at all times. It is strongly recommended that a
qualified, licensed contractor prepare the foundation for your spa. The manufacturer recommends a poured, reinforced
concrete slab with a minimum thickness of 4 inches (10cm). Wood decking is also acceptable provided it is constructed
so that it meets the requirements outlined above. The spa must be installed in such a manner as to provide drainage
away from the spa. Placing the spa in a depression without provisions for proper drainage could allow rain, overflow and
other casual water to flood the equipment and create a wet deck. Install so as to permit access to the equipment, either
from above or below, for servicing. Make certain that there are no obstructions which would prevent removal of the
cabinet side panels and access to the jets components, especially on the side with the equipment bay doors.
Outdoor Location
In selecting the ideal outdoor location for your spa, we suggest that you take into consideration:
•The proximity to changing area and shelter (especially in colder weather conditions).
•The pathway to and from the spa (free of debris, dirt, leaves as not to be tracked into spa).
•The closeness to trees and shrubbery (leaves and birds could create extra work).
•A sheltered environment (less wind, weather exposure resulting in lowered operation and maintenance costs).
•The overall enhancement of your environment. It is preferable not to place the spa under an unguttered roof
overhang since run-off water will shorten the life expectancy of spa cover.
Indoor Location
Be sure your spa will fit into the space you have chosen. Proper access into the home is needed to move the spa into
place. Ventilation may be needed because of the humidity from the spa. In most cases, a spa cover is sufficient.
Though most homes meet the requirement of 80lbs per square foot, be sure to check the load carrying capabilities of the
floor you will be installing your spa on (manufacturer not responsible). Insure you have proper drainage in the event of a
leak or water spill due to over load of spa with people causing water damage (manufacturer not responsible.) In case of
maintenance problems leave enough room around the spa to work. Choose proper flooring area for spa.
CHOOSING A LOCATION

3
Typical GFCI Load Center
(Not Supplied With Spa)
POWER REQUIRMENTS
AMP
MODEL VOLTS AMPS LOAD MARKING APPLICATION
Platinum 2020 240 60 48 3 wire#6 + Grd 3 HS2000VS
WARNING - ALWAYS USE A CERTIFIED ELECTRICIAN WHEN HOOKING UP YOUR NEW SPA.
G.F.C.I Breaker
Figure 1
Load 120 Volts
(Black) To Spa
Ground (Green)
Input
Load Neutral Bar
From House To Box
(Black) Input
From House To Box
Neutral (White) Input
From House
To Box (Red)
Input
Load Neutral
(White) To Spa
Load 120 Volts
(Red) To Spa
BREAKER BOX
(Minimum) 6 Gauge
Copper Wire Must
Be Used
Pig Tail (White) From
GFCI Breaker Going
To Neutral Bar In Box
Ground Bar Attached
To Box (Green) Input
& Out
NOTE: The White Neutral Wire from the GFCI
MUST be connected to an incoming Line Neutral.
The internal mechanism of the GFCI requires
this Neutral connection. The GFCI WILL NOT
WORK WITHOUT IT.
IMPORTANT:

4
POWER REQUIRMENTS
An illustration showing the proper electrical connections for 240 volt service has been provided for
you. (Figure 2) Be sure to follow these and all other instructions carefully. Be sure that all
connections are tight before switching on the circuit breaker.
CAUTION! Failure to abide by specification listed may result in damage to equipment and may void
the warranty. IF THE SPA IS WIRED INCORRECTLY, YOUR WARRANTY WILL BE VOID ON
ANY BURNED OUT ELECTRICAL EQUIPMENT.
G.F.C.I (Ground Fault Circuit Interrupter)
IMPORTANT
This service must be single phase. High voltage can seriously injure or kill. Always use a certified
electrician when connecting new spa.
The National Electrical Code states that a service disconnect breaker box (a G.F.C.I. can be used
for this purpose) must be located at least 5 feet away from the spa and should be conveniently
located near the equipment bay. If it is not in plain sight, keep the disconnect padlocked when in the
off position.
Remember, high voltage is still accessible in the housebreaker box even though you have turned off
the spa breaker.
G.F.C.I HOOK - UP
Figure 2
G.F.C.I
CONDUIT
HS2000VS
See Page 5
Figure 4
NEUTRAL/GROUND
BAR
INPUTS FROM
TRANSFORMER

5
CONTROLER HS2000VS - INSIDE VIEW
Figure 3
Figure 4
Fuse
Wiring
Connection
Ground
Lug
Heater Tube
Heater Element Inside
White
Neutral
Black
Red
Green
Ground Lug
Control Box Wiring
(HS2000VS)

6
WIRING DIAGRAM

7
SPEC SHEET PLATINUM MODEL 2020

8
AUDIO SYSTEM CONNECTION DIAGRAM

9
ELECTRICAL WIRING INSTRUCTIONS
IMPORTANT NOTICE: The electrical wiring of this spa must meet the requirements of the National Electrical Code (NEC)
and any applicable state or local codes. The electrical circuit must be installed by a qualified electrician and approved by a
local building/electrical inspection authority.
1. This spa must be permanently connected (hard-wired) to the power supply. No plug-in connections or extension
cords are to be used in conjunction with the operation of this spa. Supplying power to the spa which is not in
accordance with these instructions will void both the independent testing agency listing and the manufacturer’s
warranty.
2. The power supplied to this spa must be a dedicated circuit with no other appliances or lights sharing the power
provided by the circuit.
3. To determine the current and voltage and wire size required, refer to section “Power Requirements” (Pages 3, 4).
•Wire size must be appropriate per NEC and/or local codes.
•We recommend type THHN wire
•All wiring must be copper to ensure proper connections. Do not use aluminum wire.
•When using wire larger than #6 (10mm2), add a junction box near the spa and reduce to short lengths of #6
(10mm2) wire to connect to spa.
4. The electrical supply for this product must include a suitably rated circuit breaker to open all ungrounded supply
conductors to comply with Section 422-20 of the National Electrical Code, ANSI/NFPA 70. The disconnecting
means shall be accessible, located within sight from spa equipment, and shall be located at least 5 ft (1.52m)
horizontally away from the inside walls of the spa.
5. The electrical circuit supplied for the spa must include a suitable ground fault circuit interrupter (GFCI) as required
by NEC Article 680-42. (GFCI NOT INCLUDED)
6. To gain access to the spa’s power terminal block, remove the screws and cabinet panel on the side of the spa under
the control panel, then remove the two screws from the control pack.
7. Connect wires, color to color, on terminal block. TIGHTEN SECURELY! All wires must be hooked up securely or
damage could result.
8. Secure the control box door panel with screws, and then re-install the cabinet panel under the control panel.
Electrical installation is now completed.
IMPORTANT CANADA SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be followed, including the following.
1. Read and follow all instructions
2. A green colored terminal or terminal marked G, Gr, Ground, Grounding or the ground symbol is located inside
the supply terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected to
the grounding means provided in the electric supply service panel with continuous copper wire equivalent in size
to the circuit conductors that supply this equipment.
3. At least two lugs marked “Bonding Lugs” are provided on the external surface or on the inside of the supply
terminal box/compartment. To reduce the risk of electric shock, connect the local common bonding grid in the
area of the hot tub to these terminals with an insulated or bare copper conductor not smaller than No. 6 AWG.
4. All field-installed metal components such as rails, ladders, drains or other similar hardware within 10 feet (3m) of
the hot tub shall be bonded to the equipment grounding buss with copper conductors not smaller than
No. 6 AWG.
Spa Shell
Spa
Cabinet
Drain Valve
Light
Slide Valves
Control Panel
Radio-CD
Subwoofer
(Speaker)
Cabinet Panel
Figure 5
Control Pack

10
START-UP INSTRUCTIONS
FOR BEST RESULTS, READ EACH STEP IN ITS ENTIRETY BEFORE PROCEEDING WITH STEP.
FILLING THE SPA
Clear all debris from inside the spa. At the factory your spa shell was cleaned and polished, but you may want to
treat it with a specially formulated spa cleaner available by phone at 1-866-486-1365. Make sure the spa has
been installed correctly, including electrical wiring connections as specified in the wiring diagram, and the spa is
level.
Do Not Over Fill. Never fill your spa with water from a water softener, or use hot water while filling. Ensure that
your spa drain is shut off. Remove your filter lid. Place your garden hose into the filter housing and begin filling
with clean water. Continue filling spa until the water level is 2 inches above the highest water jet. Remember
every person entering a spa displaces a given volume of water, so adjust water level to number of people who
will be entering spa. If your water is extremely “hard”, it is preferable to fill halfway with hard water and the rest of
the way with softened water. Or, you may fill the entire spa with hard water if you use a special water additive
available by phone at 1-866-486-1365.
S
p
eaker
Pillow
Control Panel
Waterfall
Waterfall
Control
Pillow
Air Control
Filter Lid
Aromathera
py
S
p
eaker
Pillow
Diverter Valve
Pillow
Air Control
Air Control
Figure 6
Figure 7
Weir Door Filter
Dual Filter Cartridge
Pillow
Air Control
Air In
j
ectors
Drain
Air Control
Audio Remote
Control

11
Your spa is equipped with a Topside control panel, air control knobs, on-off waterfall valve, aromatherapy canister and
diverter valve. All controls are located on the top rail of the spa. These controls let you operate many of the special features
on your spa. The main control panel controls all of the spa functions. The heater indicator LED light and LCD display will aid
in determining the status of the spa. By familiarizing yourself with following information, you will be able to gain the full
benefit afforded by the various functions of your spa.
•Turn on power to hot tub at the home circuit breaker. The GFCI circuit breaker must be tested before each use of
the spa. Press the "Test" button on the breaker and the circuit breaker should go to the tripped position. Reset the
GFCI and ensure it stays on. The Display goes through specific sequences. At first the Display will show a series of
four numbers. The first three numbers in combination are called the software ID. Following the software ID will be
either 12 or 24, indicating the heater wattage the software is configured for. After any power-up, the spa first goes
into priming mode indicated by "Pr". During this mode heating is disabled. All pumps can be turned on to any
available speeds (as needed for priming) from the front panel. To exit Priming mode and begin normal spa
operation, press any set temperature button Up/Down). The filtration pump will automatically activate. The filtration
pump is turned on and doesn't turn off unless detected temperature gets 3 degrees above set temperature As soon
as "Pr" is indicated on the top side panel, push Jets 1, Jets 2 buttons to start the pumps. Push buttons until both
pumps are on high speed. If the pumps have not primed after two minutes, and water is not flowing from jets in the
spa, do not allow the pumps to continue to run. Turn the power off at main panel and vent air from the pumps. Do
this loosening the union nuts on the discharge side of pumps. Turn the power back on at main panel. This will
initiate a new pump priming mode. Sometimes momentarily turning pump off and on will help to prime. Do not do
this more than five times. Check and adjust, if necessary, the water and air flow of every jet. See Air Volume control
and Adjusting Jets sections for details. Priming mode will time out after 4 minutes. The filtration pump and ozone
generator will automatically turn on. After 6 minutes the actual water temperature will be displayed and heater will
turn on if heat is required. The blower purges all air lines for 30 seconds and pump 1 (low) and pump 2 (high) purge
all water lines for 5 minutes.
•Setting temperature to desired heat: To adjust your spa water temperature press the WARM or COOL button pad.
Default setting is 100F. The set temperature advances or decreases by one degree each time one of these buttons
is pressed. The heater will turn off when the temperature corresponding to the thermostat setting is achieved. The
heater will reactivate after the water cools to approximately 1F below the set temperature. Setting the thermostat at
maximum position will not accelerate the heating process. This will only result in a higher ultimate temperature. Heat
icon light is on when the heater is activated.
Add Start-Up Chemical as recommended by your dealer. Refer to Page18 for general guidance.
•Place Spa Cover On Hot Tub
•Keeping the insulating cover in place anytime the hot tub is not in use will reduce the time for heating, thereby
minimizing operating costs.
•The time required for initial heat-up will vary depending on the starting water temperature and ambient condition.
START-UP INSTRUCTIONS
Mode Cool
Warm Light Blowe
r
Jets 2
Jets 1
Heater Indicator Li
g
ht
LCD Dis
p
la
y

12
OPERATING INSTRUCTIONS
Warm/Cool
Press the “Warm” or “Cool” buttons once to display the set temperature. Each time either button is pressed again, the set
temperature will increase or decrease depending on which button is pressed. After three seconds, the LCD display will
automatically display the current temperature the spa water.
Mode/Program
Mode
Mode is changed by pressing the “Warm” or “Cool” button, then pressing the “Mode” button.
•Standard Mode is programmed to maintain the desired temperature. Note that the last measured spa temperature
displayed is current only when the circ pump has been running for at least 2 minutes. “Std ” will be displayed
momentarily when you switch into Standard Mode.
•Economy Mode heats the spa to the set temperature only during filter cycles. “Ecn” will display solid when
temperature is not current, and will alternate with temperature when temperature is current.
•Sleep Mode heats the spa to within 20°F/10°C of the set temperature only during filter cycles. “SLP ” will display
solid when temperature is not current, and will alternate when temperature is current.
Standby Mode
Pressing “Warm” or “Cool” then “Jets2” button will turn off all spa functions temporarily. This is helpful when changing filter
cartridges. Press any button to exit Standby mode.
Jets 1
Press the “Jets 1” button to turn pump 1 on or off, and to shift between low and high speeds. If left running, the low speed
turns off after two hours and high speed turns off after 15 minutes.
Jets 2
Press the “Jets 2” button to turn pump 2 on or off. If left running, the pump 2 turns off after 15 minutes.
Blower
Press the “Blower” button to turn blower on or off. If left running, the blower turns off after 15 minutes.
LED Light
Press the “Light” button to turn the spa light system on and off. LED light system preprogrammed with assortment of lighting
effects. When you turn Light off and turn on again within five (5) seconds it advances to the next effect. When you turn Light
off for more than five (5) seconds, it remembers that last effect you selected. The next time you turn on the Light will display
the same effect. The Light will automatically turn off after approximately four (4) hours.
The spa is equipped with LED light system and music module the following sequence effects can be selected via on-off Light
button:
1) Color wheel; 2) Music modulated mode; 3-8) Different colors; 9) Flashing through the color sequence.

13
OPERATING INSTRUCTIONS
Filtration Pump
Your system equipped with the filtration pump. The filtration pump provides 24 hour continuous water circulation and
filtration. The filtration pump turns over the entire spa water capacity at a minimum of 3 times every hour. It works like this:
a dedicated, energy efficient filtration pump constantly draws water from the spa through the filter and the heater (heating
only when necessary), then back to the spa. The ozone output is on whenever the filtration pump is running except when the
jet pump or blower is activated by the user. The ozone generator will turn off for one (1) hour any time a function button (Jets
1, Jets 2 or Blower.) is pressed. The filtration pump will turn off for 30 minutes at a time when the water temperature
reaches 3°F (1.5°C) above the set temperature (most likely this will happen in a very hot climate or during summer).
Heater
Your spa is equipped with an electrical heater. By setting your thermostat to the desired temperature, your heater will
automatically turn on and off as needed. The temperature set point (set temperature) can be adjusted from 80°F to
104°F/26°C-40°C. To raise the set temperature press the “Warm” button. To lower the set temperature, press the “Cool”
button. The start up temperature is set at 100°F/37.5°C. The last measured temperature is constantly displayed on the LCD
display.
•In Economy mode the heater heats the spa water only during filter cycles.
In sleep mode the heater heats the spa water to within 20°F (11°C) of set temperature only during filter cycles.
Present Filter Cycles (For use during economy mode)
The first filter cycle begins 6 minutes after the spa is energized. The second filter cycle begins 12 hours later. Filter duration
is programmable for 2, 4, 6, 8 hours or for continuous filtration (indicated by “FILC ”). The default filter time is 2 hours. To
program, press “Warm” or “Cool”, then “Jets 1”. Press “Warm” or “Cool” to adjust. Press “Jets 1” to exit programming. At the
beginning of each filter cycle the blower purges for 30 seconds; the pumps purge for 5 minutes. The only effect filter duration
has is: 1) During the filter, the circ pump never turns off, and 2) In Economy and Sleep Modes, heating only occurs during
the filter cycle.
Ozone water maintenance system
Your spa is equipped with ozone purification system. You will find that your spa water stays fresh and clear with significantly
less chemical sanitizer usage. You will be able to go longer between complete spa draining. The ozone generator operates
in conjunction with the filtration pump. Ozone generator is on any time the filtration pump is running. Ozone generator will
turn off for one (1) hour any time a function button (Jets 1, Jets 2, Blower.) is pressed.
Freeze Protection
If the temperature sensor detects a temperature drop to 44°F (6.7°C) within the heater, then the pump automatically
activates to provide freeze protection. The equipment stays on until four (4) minutes after the sensors detect that the spa
water temperature has risen to 45°F(7.2°C) or higher.

14
Air Volume Control
Your spa is equipped with Air Volume Controls. Each jet system has its own air control. These controls allow you to regulate
the amount of air, which is mixed with the water entering through the jets. Counterclockwise rotation adds more air and
clockwise rotation reduces airflow. To minimize heat loss, these controls should be closed when the hot tub is not in use.
Waterfall control
Turn the waterfall valve clockwise to decrease or turn off waterfall output. It takes four full revolutions to change the waterfall
from full off to a full on flow rate.
Adjusting Jets
All jets in your new spa can be adjusted for high and low impact massage, providing an ultimate massage. Each jet has its
own water volume and directional or oscillating flow adjustment.
To adjust jets: Turn outer dial counterclockwise to increase water volume. Turn outer dial clockwise to decrease water
volume or to shut jet off. For adjustment of the directional jets move the nozzle of jet to any angle.
Aromatherapy
Simply remove the Aromatherapy injector cap, drop in the injector basket of your favorite scented beads. When the Blower
is activated, the scent will be released into the spa vapor through the air injectors. Please call 1-800-749-8003 or visit
www.platinumhottubs.com on line for replacement of scented beads.
Diverter Valve
This control allows you to regulate the amount of water distributed by pump 2 from seat to seat.
Audio System
Spas equipped with audio systems offer enhanced spa enjoyment. This model includes a high quality AM/FM/CD/MP3
stereo receiver with two high quality speakers and a sub woofer for unsurpassed sound quality and long life.
Two speakers located on spa lip corners are designed for manual exposure and retraction. To expose each speaker for
audio playback, simply press download on each enclosure to unlatch its pop-up mechanism, then release. To retract each
speaker before covering spa, gently press downward on each enclosure you will feel a slight “click”, then release. Sub
woofer is located inside cabinet in right corner (see figure 5, page 9). Audio system is equipped with remote control panel for
safe and easy operation from within the spa.
Caution: Never step or sit on speaker enclosure. Always retract speakers prior to covering spa. For details see manual,
and audio connection diagram (See page 12). Visit www.platinumhottobs.com on line to download manual.
OPERATING INSTRUCTIONS

15
Message Meaning Action Required
No message on display. Power has been
cut off to spa. The control panel will be disabled until power returns. The system reset the time of day on each power up. Spa settings are preserved.
OHH Overheat"- The spa has shut down. One of the sensors detected 118egree F
(approximately 47.8 degree C) at the heater.
Do not enter the water. Remove the spa cover and allow the water to
cool. Once the heater has cooled, reset by pushing any button. If the
spa does not reset, shut off the power to the spa and call for service.
OHS
Overheat"- The spa has shut down. One of
the sensors detected that the spa water is
110egree F (approximately 43.3 degree C).
Do not enter the water. Remove the spa cover and allow the water to
cool. At 107 degree F (approximately 41.7 degree F), the spa should
automatically reset. If the spa does not reset, shut off the power to the
spa and call your service.
ICE Ice" - Potential freeze condition detected.
No action required. The pumps and the blower will automatically activate regardless of the spa status.
SnA
Spa is shut down. The sensor that is
plugged into the "Sensor A" jack is not
working correctly.
Check the sensor "B" plug connection to circuit board. If the problem
persists, contact your dealer or service. (The problem may appear
temporarily in an overheat situation and disappear when the heater
cools).
SnS
Sensors are out of balance. If this is
alternating with temperature, it may just be
temporary condition. If the display shows
only this message (periodically blinking), the
spa is shut down.
If the problem persists, contact service.
HFL
A substantial difference between sensors
was detected. This could indicate a flow
problem.
Check water level in spa. Add water if necessary. Be sure that slide-
valves are open. Make sure the circulation pump have been primed
and has power.
LF
Persistent low flow problems. Displays on
the fifth occurrence of the "HFL" message
within 24 hours. Heater is shut down, but
other spa functions to run normally.
Follow actions required for "HFL" message. Heating capacity of the
spa will not reset automatically; you may press any button to reset or
cycle the power off and on.
dr Inadequate water detected in heater.
Displays on third occurrence of "dr"
message. Spa is shut down for 15 minutes.
Check water level in spa. Add water if necessary. Be sure that slide-
valves are open. Make sure the circulation pump have been primed
and has power. On the third consecutive occurrence of the dr
message (without a successful heating cycle in between) the panel will
display dr4.
Dr4
Inadequate water detected in heater.
Displays on third occurrence of "dr"
message. Spa is shut down and will not
reset in 15 minutes.
Check water level in spa. Add water if necessary. Be sure that slide-
valves are open. Make sure the circulation pump have been primed
and has power. Press any button to reset.
-- Temperature Unknown After the pump has been running for 2 minutes, the temperature will be
displayed
Snb Spa is shut down. The sensor that is
plugged into the Sensor ”B” jack is not
working.
If the problem persists, contact service. (May appear temporarily in an
overheat situation and disappear when the heater cools.)
DISPLAY MESSAGES

16
Draining and Refilling your spa
WARNING!
To prevent damage to spa's components, turn off power before draining it. Do not turn the power back on until your spa has
been refilled.
Depending on your spa model, the drain valve is located on the front left or right side of the spa (see page 9). The drain
valve is flush mounted to the spa frame. To drain spa, pull the spout out, (approximately 2”), leaving the exterior end cap on.
Once extracted the drain valve will stay in the closed position. Remove the end cap and attach garden hose to exposed
threads. After the garden hose is installed, push the spout back in halfway to actuate the drain. Drain valve will drain
approximately 5 gallons of water per minute.
Filter cleaning and Cartridge Replacement.
Press “warm” or “cool” button then “Jets 2” button. It will temporarily turn off all spa functions and put the spa in standby
mode.
The Filter cartridges should be checked periodically. In normal use, check them at least once a month. Keep them clean. An
obstructed filter cartridge reduces water quality and inhibits proper system performance.
Removable filter cartridges are located inside the filter well. To remove them lift the filter lid, then rotate each filter cartridge
counterclockwise to unthread from mating wall fitting.
Remove both cartridges from filter well.
Use a garden hose with straight flow nozzle to wash down the filter element. Work from the top down, holding the nozzle at
45 degree angle, and wash all the pleats with emphasis between pleats.
Rinse until all dirt and debris is gone.
Re-install filter. Press any button to exit standby mode.
Replacement cartridges may be purchased by phone [phone]. (Part # 6136)
Care Of The Exterior
Spa Shell
Your spa shell is made of acrylic and Microban®. Stains and dirt generally will not adhere to the surface. Use of a soft rag
or a nylon scrubber should easily remove most dirt. Most household chemicals are harmful to your spa’s shell. The only
products which have passed the manufacturer’s test are Soft Towel and Windex. Sodium bicarbonate (baking soda) can
also be used for minor surface cleaning. Always thoroughly rinse off any spa shell cleaning agent with fresh water.
NOTES: Iron and copper in the water can stain the spa shell if allowed to go unchecked. Ask your Hydro Spa dealer about
a stain and scale inhibitor to use if your spa water has a high concentration of dissolved minerals.
The use of alcohol or any household cleaners other than those listed to clean the spa shell surface is NOT recommended.
DO NOT use any cleaning products containing abrasives or solvents since they may damage the shell surface. NEVER
USE HARSH CHEMICALS! Damage to the shell by the use of harsh chemicals is not covered under the warranty.
IMPORTANT: Some surface cleaners contain eye and skin irritants. Keep all cleaners out of the reach of children and use
care when applying.
Maintenance Free Cabinet
The spa consists of a rigid polymer that combines the durability of plastic with the beauty of a redwood looking cabinet. The
cabinet will not crack, peel, blister or delaminate. Cleaning consists of simply spraying the cabinet with a mild soap and
water solution to remove any stains and residue.
Pillow care
Remove and clean the headrest pillows as needed with soapy water using a cloth or soft-bristle brush. Always remove the
pillows when adding chemical shock treatment to the spa water. The pillows can be returned to the spa when sanitizer
reading drops below 5ppm. Never attempt to remove the pillows by pulling on them. Grasp pillow with finger tips and gently
pry outward from spa shell.
SPA CARE AND MAINTENANCE
Filter Cartridge

17
SPA CARE AND MAINTENANCE
Care Of Spa Cover
To clean and condition the vinyl cover:
•Remove the cover from the spa and gently lean it up against a wall or fence.
•Using a garden hose, spray the cover to loosen and rinse away any dirt or debris.
•Using a sponge and/or a soft bristle brush, and a very mild soap solution (one teaspoon dishwashing liquid with two
gallons of water), or baking soda (sodium bicarbonate), scrub the vinyl top in a circular motion then rinse clean.
•Scrub the cover’s perimeter in the same matter as the top of the cover, and rinse clean with water.
•Rinse off the underside of the cover with water only (use no soap), and wipe it clean with a dry rag.
•To condition the cover after cleaning, apply a thin film of vinyl cleaner to the surface and buff to a high luster.
Important reminders:
•DO remove snow buildup to avoid breakage of the foam core from the additional weight of the snow.
•DO lock cover locking straps to secure the cover when the spa is not in use.
•DO NOT walk or stand on top of cover.
•DO NOT drag or lift the spa cover using either of the flaps, or the cover lock straps.
Vacation Care Of Spa
Follow these instructions to ensure that the water quality of your spa is maintained:
For Short Periods (3 to 5 days)
•Adjust the pH
•Sanitize the water
•Lock cover for safety
For Long Periods (5 to 14 days)
•Set temperature to its lowest level approximate water temperature of 80.0F.
•Adjust the pH
•Sanitize the water
•Lock cover for safety
Return Procedures
•Sanitize the water following shock procedures
•Return water temperature to original setting
•Insure chlorine level had dropped below 5.0 ppm
NOTE: If you plan on not using your spa for periods exceeding 14 days, you may ask a family member or neighbor to assist
with your spa maintenance, and if not available you will need to drain or winterize spa.
Winterizing Your Spa
WARNING: Allowing your spa water to freeze will cause severe damage to the spa shell, equipment, and plumbing
and WILL VOID WARRANTY.
The following steps should protect your spa from freezing:
•Remove the screws holding your spa excess panel door.
•Open the drain valve, open the pumps plugs, and the spa will drain by gravity flow.
•Turn blower on only and allow it to blow out any water remaining in the plumbing lines. (Should take no more than 5
minutes).
•Disconnect the spa from the power supply.
•Remove the filter cartridge, then clean and store in a dry place.
•Attach a wet/dry shop vac (capable of blowing air as well as vacuuming) into the filter housing.
•Reinstall the filter housing lid.
•Use the shop vac to remove water inside spa blown through jets.
•Use a shop vac and clean towel and remove any remaining water from bottom of spa until dry.
•Leave the drain open.
•Install the spa cover and fasten with tie down safety locks.