Playcore ultra site TR-32-RT User manual

Model # TR-32-RT
4/29/2015 Page 1 of 9

1675 Locust Street
Red Bud, IL 62278
Phone: [phone]
Fax: [phone]
WARRANTY & TERMS
WARRANTY: 5 Year Limited Warranty on Thermoplastic coated elements. Ultra Play guarantees all items for one full year to be
free of defects in workmanship or materials when installed and maintained properly. We agree to repair or replace, any items
determined to be defective. Items specifically not covered by this warranty include vandalism, man made or natural disasters, lack of
maintenance, normal weathering or wear and tear due to public abuse.
Damages or loss in transit is the responsibility of the carrier, whether visible or concealed. It is the responsibility of the recipient to
assure that the order is received complete. Before signing the delivery receipt, inspect the shipment immediately and completely. Note
any damages or shortages on the bill of lading. Damage reports must be filed within 10 days. Ultra Play is NOT responsible for
damages or loss in transit. Title to all goods passes to the customer at the time of shipment. Ultra Play will assist in filing claims if the
freight arrangements were made by Ultra Play at your request.
CANCELLATIONS AND RETURNS: Cancellations are only accepted with approval of Ultra Play. No merchandise shall be returned
without a Return Goods Authorization number which is issued by customer service. Any authorized merchandise must be carefully
packed and received in saleable condition. A restocking charge of up to 25% will be applied to all returned goods when the error is not
the fault of Ultra Play. All returns must be shipped freight prepaid.
4/29/2015 Page 2 of 9

Owners and installers please note these safety warnings and make use of this checklist on a regular basis.•
Follow installation instructions when erecting equipment.•
Ground surfaces around equipment should be restored as needed. Concrete footings should never be exposed. Surface depth•should comply with ASTM and CPSC specifications.
Check for and repair damage caused by wear or vandalism, a major factor in injury causing situations.•
All protruding bolts should be covered or cut off and finished smooth. Sharp edges on pipes should be capped or removed. Check•for bent, broken, or severly worn pipe, and replace.
All equipment should be free of rust and repainted whenever necessary to deter rusting.•
We provide our customers with layout sheets and installation instructions. Please keep on file the specifications sheet that contains•the listing of every part used.
Never add components not intended for use with this product.•
Regular maintenance is necessary in this and all park and recreational equipment to insure the safety of the user.•
Note: Proper maintenance of equipment requires regular tightening of all bolts, nuts, and setscrews.•
Note: Regular checking of all parts, castings, etc. should be made. If a part is broken or worn, it shoud be replaced immediatly.•
Check to be sure all fittings are tight and that bars and pipes do not move.•
Replace all worn S-hooks. S-hooks must be completely closed. Failure to close S-hooks can result in serious injury to the user.• NEVER reuse S-hooks.
Test for free movement of swing hanger and other moving attached parts.•
Check for worn chains and replace them.•
A soft resilient surface should be placed under all swings extending at least twice the height of the top rail both front and back.•
SAFETY WARNINGS & EQUIPMENT INSPECTION
4/29/2015 Page 3 of 9

5/16" ID x 7/8"
Nylon Spacer
800-45-ULTRA www.ultrasite.com
1/2" Wrench 1/2" Socket Wrench Tape Measure Level
HARDWARE AND TOOLS REQUIRED
5/16" Hex Nut
5/16" x 3"
Carriage Bolt
5/16" Washer
4/29/2015 Page 4 of 9

800-45-ULTRA www.ultrasite.com
ULTRA SITE PRODUCT SPECIFICATIONS
TR-32
RECYLCED PLASTIC SLAT TRASH RECEPTACLE
Slats: Minimum of 96% commingled post-consumer or post-industrial recycled plastic 2x4. With a maximum of 4% due to various
additives including color and UV stabilization to obtain desirable properties.
Frame: Rings are 3/16” x 2” flat. Bottom plate is precision punched from 12 ga. sheet steel. All electrically MIG welded.
Frame Coating: Hot dipped galvanized.
Hardware: All hardware fasteners are zinc coated.
Dimensions: 26” Diameter. Trash receptacle has an overall height of 34”.
RT-32
32 Gallon Round Top
Material: Heavy-Duty structural Plastic
Dimensions: 24-7/8" Outside Diameter x 24" Inside Diameter x 11-3/4" High
Overall Receptacle Dimensions: 28-1/4" Diameter x 44-1/2" Tall
4/29/2015 Page 5 of 9

Attach the 34" Recycled planks to the TR-32 Ring and TR
Bottom Ring assembly as shown using specified hardware.
ITEM NO. PartNo DESCRIPTION Qty.
1 01-05-0054 TR bottom ring assembly 1
2 01-05-0041 TR-32 Ring 1
3
BRN34-2x4-TR,
CDR34-2x4-TR,
GRN34-2x4-TR,
or GRY34-2x4-
TR
2 x 4 Brown Recycled TR Plank (34"), 2 x 4
Cedar Recycled TR Plank (34"), 2 x 4 Green
Recycled TR Plank (34"), or 2 x 4 Gray
Recycled TR Plank (34") 20
4 33-06-0022 5/16" x 3" Carriage Bolt (Zinc) 40
5 33-01-0001 5/16" Hex Nut (Zinc) 40
6 33-02-0001 5/16" Zinc Plated Washer 40
7 RT-32 32 Gallon Round Top 1
8 94639A215 5/16" x 7/8" Nylon Spacer 40
Note: 5/16" x 7/8" Nylon Spacers fit on the 5/16" x 3" Carraige
Bolts between the Recycled Planks and the TR-32 ring.
28 1/4"
800-45-ULTRA www.ultrasite.com
COMPONENTS
2
4 3
8
5
7
6
1
44 1/2"
33 3/4"
4/29/2015 Page 6 of 9

24"
12"
3"
12"
800-45-ULTRA www.ultrasite.com
INGROUND MOUNTING OPTION
INGROUND MOUNT FOR TRASH RECEPTACLE
Frame: 2-3/8” O.D. x 12 gauge pre-galvanized structural steel tubing.Mounting
points 3 gauge 8” x 8” steel flat bar. All electrically MIG welded.
Frame Coating: Electrostatic powder coated application oven cured.
Hardware: All stainless steel hardware fasteners. (Included).
Dimensions: Overall dimension is 24 1/4” x 8” x 8”.
Attach the IG KIT to the TR-32-R as shown using specified hardware.
Estimated Required Concrete:
5 - 50lb Bags of Concrete Mix
ITEM NO. PartNo DESCRIPTION QTY
1 33-02-0007 5/16" SS Washer 8
2 P-01-05-0052 receptacle inground mount 1
3 33-05-0029 5/16" x 1" Machine Bolt (SS) 4
4 33-03-0012 5/16" Kep Nut (SS) 4
4
3
1
2
4/29/2015 Page 7 of 9

ITEM NO. PartNo DESCRIPTION QTY
1 33-02-0007 5/16" SS Washer 8
2 P-01-05-0053 receptacle surface mount 1
3 33-05-0029 5/16" x 1" Machine Bolt (SS) 4
4 33-03-0012 5/16" Kep Nut (SS) 4
4
3
12
800-45-ULTRA www.ultrasite.com
SURFACE MOUNT MOUNTING OPTION
SURFACE MOUNT FOR TRASH RECEPTACLE
Frame: 2-3/8” O.D. x 12 gauge pre-galvanized structural steel tubing. Surface
mounting points are 3 gauge 8” x 8” steel flat bar with four holes. Receptacle mounting
points are 3 gauge 6” x 6” steel flat bar with 4 holes. All electrically MIG welded.
Frame Coating: Electrostatic powder coated application oven cured.
Hardware: All stainless steel hardware fasteners. (Included).
Dimensions: Overall dimension is 3-3/4” x 8” x 8”.
Attach the SM KIT to the TR-32-R as shown using specified hardware.
Recommended Surface Mount Hardware:
3/8" x 3-1/2" Concrete Expansion Anchor Bolts
(Not Included)
4/29/2015 Page 8 of 9

800-45-ULTRA www.ultrasite.com
LINER OPTION
PL-32
32 Gallon Liner
Made of heavy duty plastic.
4/29/2015 Page 9 of 9