PLENBO G-CASE User manual


＿

Handheld Mode
Attach your Switch
1. Open the top flap of the G-case.
2. Slide Switch down till it sits
properly. Then snap on the flap.
KEEP OUT
*Note: G-case comes in two models:
one for Switch Regular and one for
Switch OLED. Make sure you choose
the right one to fit perfectly.

Handheld Mode
Turn on/off power
Press battery power button to start
charging. Press it again to stop charging.
KEEP OUT

Handheld Mode
Pair Bluetooth
1. Press both buttons on the G-case
at the same time to activate them.
2. Press either Bluetooth button.
The indicator will flash slowly,
showing it's ready to connect.
3. Press and hold the same button
until the indicator flashes quickly,
indicating pairing mode. Put your
earphone in pairing mode too. When
they're paired, the indicator will
stay on.
*Note: G-Case can pair two sets of
devices at the same time.
KEEP OUT

Handheld Mode
Change Grips
Push the grips downward to take
them off. Slide grips upward the rails
till you hear a click.
Card slot is hidden here;
KEEP OUT

KEEP OUT
Handheld Mode
Recharge other devices
Take the battery off the G-case, charge
the phone or other digital devices via
the USB-C port.
*Note: fuel the battery with a USB-C
fast charger, recharge other devices
with a USB-C to USB-C cable.

Tabletop Mode
Step 1
Detach the Switch from the G-Case. Push
the left Joy-con holders upward and the
right downward to remove them.
KEEP OUT

Tabletop Mode
Step 2
Slide to attach the left and right Joy-Con
holders together.
Open the side stands from the holders,
then slide the Joy-Con controllers down.
KEEP OUT

Tabletop Mode
Step 3
Put the Switch into the G-Case,
lock into place. Flip out the
kickstand on the back of G-Case
and set it on a flat surface.
KEEP OUT

KEEP OUT
TV Mode
TV Connection
1. Plug in the OneDock to a wall
outlet; 2. Connect the G-case to the
USB-C port on the OneDock with the
original Type-C cable; 3. Put one end of
the HDMI cable into the terminal of the
OneDock and connect the other end
into the HDMI port on the TV.
*Note: Please do not use the USB-A port
on the dock to connect the G-case.

1. Plug OneDock into a power outlet.
2. Connect the Switch with the
OneDock via the USB-C to USB-C
cable included.
KEEP OUT
TV
For Charging

1. Plug OneDock into a power outlet.
2. Connect Switch with OneDock via
a USB-C to USB-C cable.
3. Connect OneDock with TV/screen
via HDMI cable.
KEEP OUT
For Screen Mirroring
*Note: Please do not use the USB-A port
on the dock to connect the G-case.

1. Connect computer with OneDock
via a USB-C to USB-C cable.
2. Insert USB flash drive into the
USB-A port on the OneDock.
KEEP OUT
For Data Transferring

Consoles
Controllers
Switch / Switch OLED
PC / Android TV Box
PS5 / PS4 / PS3
Switch Pro

1. Go to the Switch’s “System Settings”,
select “Controllers and Sensors”, then turn
on “Pro Controller Wired Communication”.
2. Plug OneDock into a power outlet and
connect it with Switch.
3. Connect Adapter with console via USB-A
port.
4. Press Adapter button to enter pairing
mode.
5. Set controller to pairing mode, and
bluetooth will connect automatically.
Adpater status light
Flash slowly: scanning
Flash rapidly: connecting
Always On: connected
KEEP OUT
Connect to Controllers
*Note: It's normal for the light to stay off
until you connect the Switch. There's
nothing wrong with it.