Pliant PAC-MC4W-IO User manual

For more information visit
www.plianttechnologies.com
QUICK START GUIDE
CUSTOMER SUPPORT
Pliant Technologies oers technical support via phone and
email from 07:00 to 19:00 Central Time (UTC−06:00), Monday
through Friday.
1.844.475.4268 or +1.334.321.1160
customer[email protected]
You may also visit our website (www.plianttechnologies.com)
for live chat help. (Live chat available 08:00 to 17:00 Central
Time (UTC−06:00), Monday through Friday.)
Additional Documentation
This is a quick start guide. For additional
documentation on MicroCom XR, visit our
website. (Scan this QR code with your mobile
device to navigate there quickly.)
COPYRIGHT © 2021 Pliant Technologies, LLC. All rights reserved. The Pliant™ word
mark and the Pliant “P” logo are registered trademarks of Pliant Technologies, LLC. Any
and all other trademark references within this document are property of their respective
owners.
Document Reference: D0000628_A
IN THIS BOX
WHAT’S INCLUDED WITH THE AUDIO I/O
ADAPTER?
• PAC-MC4W-IO: 4-Wire In/Out and Two-Way Radio Headset
Adapter
• CAB-4W-WI: 3.5 mm TRS to RJ45 cable
• 3.5 mm to 3.5 mm Audio Cable
• USB-C Charging Cable
• Quick Start Guide
ACCESSORIES
OPTIONAL ACCESSORIES
• PAC-MOT-X83: MicroCom Two-Way Radio Adapter for
Motorola Radio
• PAC-KEN-2P: MicroCom Two-Way Radio Adapter for
Kenwood Radio
• Selection of compatible dual-mini (DMG) headsets (see
Pliant website for more details)
AUDIO I/O
HEADSET ADAPTER
Only compatible with the MicroCom XR BeltPack.

OPERATION
Audio I/O Headset Adapter
LED Indicators
Connect to a Wired Intercom
1. Verify all of the equipment is powered o.
2. Connect the 3.5 mm end of either the CAB-4W-WI or
the 3.5 mm to 3.5 mm audio cable to the wired intercom
connection on the headset adapter.
3. Connect the other end into a wired intercom system’s
4-Wire In/Out connection.
4. Connect a beltpack using the cable
attached to the headset adatper.
Note: Correct orientation as shown to the
right.
5. Connect a headset to the adapter’s
headset connection (optional).
6. Set the In/Out volume/gain levels of
the wired intercom in the center position.
7. Power on all attached equipment.
8. Adjust the beltpack volume and wired intercom volume/
gain levels as needed.
Connect to a Two-Way Radio
1. Verify all of the equipment is powered o.
2. Connect the 3.5 mm end of a two-way radio cable (not
included) to the two-way radio connection on the bottom of
the headset adapter.
3. Connect the other end into the accessory port on a two-
way radio.
4. Connect a beltpack using the cable attached to the
headset adatper.
Note: Correct orientation as seen in the figure above.
5. Connect a headset to the adapter’s headset connection
(optional).
Power LED turns Blue Power ON
Power LED OFF Power OFF
Power LED turns Red Charging
Power LED OFF Fully Charged
PTT LED turns Red PTT Engaged
6. Set the two-way radio volume levels of the attached two-
way radio to 70% of total volume.
7. Set the volume of the attached beltpack to level 4.
8. Power on all attached equipment.
9. Adjust the beltpack volume and two-way radio volume
levels as needed.
To Talk over Connected Two-Way Radio
• Press and hold the PTT button on the adapter to trigger the
PTT of the attached two-way radio.
• Press and hold the Top Button on any beltpack in the system
to trigger the PTT of the attached two-way radio.
CAB-4W-WI CABLE
Pin Out Connections
3.5 mm RJ45
- 1
- 2
T 3
R 4
S5
6
- 7
- 8