PLNetworks PLS100WF User manual

Copyright © 2018 PLNetworks 1
The information contained herein is the property of PLNetworks and is provided without liability of errors,
omissions, and mistakes. No part may be reproduced or copied without written permission or contract.
2.4GHz LoRa Modem
PLS100WF User Guide

Copyright © 2018 PLNetworks 2
The information contained herein is the property of PLNetworks and is provided without liability of errors,
omissions, and mistakes. No part may be reproduced or copied without written permission or contract.
Revision History
Who Version Date Comment
Arron H 1.0 Oct28, 2019 Initial release

Copyright © 2018 PLNetworks 3
The information contained herein is the property of PLNetworks and is provided without liability of errors,
omissions, and mistakes. No part may be reproduced or copied without written permission or contract.
TABLE OF CONTENTS
1.Introduction ......................................................................................................................... 4
2. Hardware Specification .................................................................................................... 4
3. Component ......................................................................................................................... 5
4. FCC ...................................................................................................................................... 6
5. A/S ........................................................................................................................................ 6

Copyright © 2018 PLNetworks 4
The information contained herein is the property of PLNetworks and is provided without liability of errors,
omissions, and mistakes. No part may be reproduced or copied without written permission or contract.
1.Introduction
The PLS100WF, a 2.4GHz LoRa modem, is a low-power, long-range, high-speed industrial IoT
device .
2. Hardware Specification
The hardware of PLS100WF specifications are as follows.
MCU * ARM® Cortex®-M4 32-bit processor
with FPU, 64 MHz
RF Transceiver
* LoRa Technology RF modulation
* Frequency: 2412 MHz ~ 2472 MHz
* Modulation: GFSK
Internal Memory 512 KB Flash, 64 KB SRAM
Data Rate up to 200 kbps (LoRa)
RF Tx Power 6.1 dBm(max)
DC Input Voltage + 3.6 VD
Power Supply 19000mAh Lithium Battery
Antenna 2.4GHz Internal Antenna
Operating Temp. -30℃ ~+70℃
Dimension 70 X 99 X 58 mm
The explanation of each part of PLS100WF as follows.

Copyright © 2018 PLNetworks 5
The information contained herein is the property of PLNetworks and is provided without liability of errors,
omissions, and mistakes. No part may be reproduced or copied without written permission or contract.
① Main body
② Band hole: Band hole for Fix
③ Cover screw
④ Cover
3. Component
Component EA
Main Body 1
Screw driver 1

Copyright © 2018 PLNetworks 6
The information contained herein is the property of PLNetworks and is provided without liability of errors,
omissions, and mistakes. No part may be reproduced or copied without written permission or contract.
4. FCC
INFORMATION TO THE USER
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.


CAUTION:Changesormodificationsnotexpresslyapprovedbythepartyresponsiblefor
compliancecouldvoidtheuser'sauthoritytooperatetheequipment.

FCCRadiationExposureStatement:
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.
Thisequipment
shouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.
5. A/S
 Company : PLNetworks
 Add : #210, HANA EZ TOWER, 10, Seongnam-daero 43beon-gil, Bundang-gu,
Seongnam-si, Gyeonggi-do, Republic of Korea
 Web : http://www.plnetworks.co.kr