Point Mobile PM5 User manual

PM5 User Manual
1
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
PM5 (Bluetooth Barcode reader) User Manual
PM5 is Bluetooth barcode reader which has 2D Scanner and single ring trigger.
User should pair PM5 with device what has a Bluetooth. Then they can check a data,
adjust settings and so on.
1. Major Parts.
1) PM5 terminal
①Scan Key
②Battery locker
③LED light

PM5 User Manual
2
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
2) Single Trigger
①Scan key
②Pin for locking PM5
③Finger Ring Strap
PM5 can connect with single trigger.
Single trigger has a finger strap so user
can put PM5 on their finger.

PM5 User Manual
3
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
2.How to Charge
User can charge PM5 with USB-C Adaptor
Charging ONLY
USB C connector

PM5 User Manual
4
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
3.PM5 Battery Specification
Standard Battery
510mAh / 3.8V
Extended Battery
700mAh / 3.8V
urnOn /Off PM550
Getting Started 3.
4.Turn on / Off
1) Turn On
①Put the battery in PM5
②Push Scan key. Then you can check red LED light from bottom side and beep sound.
2) Turn Off
Remove the battery in PM5.
5.Pairing
User can use app “RingControl” in their phone for pairing and setting of PM5.
RingControl

PM5 User Manual
5
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
For pairing with PM5 and other device, User should read barcode in App.
Reading the barcode in the
app via PM5

PM5 User Manual
6
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
Pop-up shows when
pairing is a success.
From the next time, the list
your device in it shows up.
User can choose the device
from it for pairing.

PM5 User Manual
7
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
6.Scan & Setting
Learningt he basics
After pairing, user can use
scan function.
User can adjust the setting
such as beep volume or FW
update from setting button

PM5 User Manual
8
© 2006 –2020 POINTMOBILE Co., Ltd. All rights reserved
FCC & IC APPROVAL
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful Interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Caution: Any changes or modifications to this device not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver that comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.(2)
This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes aux RSS exempts de licence d'Innovation,
Sciences et Développement économique Canada. Son fonctionnement est soumis aux deux conditions suivantes:(1) Cet appareil ne
doit pas provoquer d'interférences.(2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent
provoquer un fonctionnement indésirable de l'appareil.
This device complies with FCC/IC RF exposure requirements.
Cet appareil est conforme aux exigences d'exposition aux RF FCC/IC.
FCC ID : V2X-PM5
IC : 10664A-PM5