Polanik T6-RCU User manual

TECHNICAL SPECIFICATION
ASSEMBLY MANUAL
LED race clock with results option
T6-RCU
File: 2016-01-11
PRODUCT SUPPORT
Pawel Ciechanowski
p.ciechano[email protected]m

Technical specification / user manual T6-RCU 2 / 6
ATTENTION!
The board is an electronic device and it requires careful handling!
I. General use
The race clock led display is designed to display running time or 6-digit results during sports events and training
programmes. Counting time up and down, additional result display feature, handheld time control keypad and
numeric keypad for entering 6-digit results, integration with chronometer.

Technical specification / user manual T6-RCU 3 / 6
II. Technical specification
Code
T6-RCU
Type
Race clock with results option
Power supply AC [V]
230
Power consumption [VA]
50
Display box dimensions [mm]
1550 x 340 x 100
Frontal cover
solid polycarbonate
Display type
LED
Display colour
red
Digit height [cm]
25 cm
Good visibility [m]
100 m
Maximum visibility [m]
125 m
Displayed time format –standalone operation
HH:MM:SS
Displayed time format –standalone operation with numeric keypad
00:00.00
Displayed information –time format (operation with chronometer)
HH:MM:SS
Max view angle [°]
120
Weight [kg]
10
Casing
aluminium, powder painted
Temperature range
from -10°C to +50°C
Set contains
tripod, time control keypad, numeric
keypad, power cable

Technical specification / user manual T6-RCU 4 / 6
III. Assembly
1. Set up the clock in a suitable place.
2. Install the board on a tripod.
3. Depending on the operation mode connect the control cable:
a) to the socket located on the display side, for the time control keypad or chronometer
b) to the socket located on the display bottom, for the numeric keypad
4. Connect the control cable to the power supply.
5. The clock tests led display units (all segments light up for about 2s).
6. Then the clock shows time 0s. and it is ready to use.
IV. Operating
1. Standalone operation –time control keypad
a) press USTAW/SET to adjust first two digits (hours HH), while the digits are fleshing press +to set up their
initial value, then press USTAW/SET again to adjust next two digits (minutes MM), repeat the sequence to set
up last group (seconds SS),
b) press START to start measuring time from the initially adjusted value,
c) press STOP to stop measuring time,
d) press and hold CLEAR/KASUJ for approx 2 s. to reset the clock.
Time display –time control keypad
Power supply
Results control –numeric keypad
Time control keypad
Numeric keypad

Technical specification / user manual T6-RCU 5 / 6
2. Standalone operation –results control with numeric keypad
a) press the keys 0-9 to display the result,
b) press # key to erase the result.
3. Operation with chronometer
Preparation for use:
-connect the display with the chronometer using the included cable
START UP starts to count up time from the initial value
+increases hours/ minutes/ seconds when setting the initial value
-decreases hours/ minutes/ seconds when setting the initial value
KASUJ/CLEAR clears the clock to 0
USTAW/SET starts setting the initial value
STOP stops the clock
START DOWN starts to count down time from the initial value

Technical specification / user manual T6-RCU 6 / 6
-switch on the display board,
-switch on the chronometer.
See the instruction manual of the chronometer for further reference.
V. Storage and Maintenance
The display board is an electronic device and it requires careful handling. During idle periods it must be stored in
a roofed and dry place. Before cleaning, disconnect the power cord. Wipe the front panel with a soft cloth or an agent
for cleaning polycarbonate surfaces.
VI. Declaration
1) No. 2016-01-11
2) Issuer’s name: POLANIK
Issuer’s address: Zyczliwa 11, 97-300 Piotrkow Tryb.
3) Object of declaration:
4) The object of declaration described above is in conformity with the requirements of the company production internal norms.
Additional Information
5) Declaration for:
Buyer/Distributor/User
Signed for and in behalf of:
POLANIK
2014-07-29 Piotrkow Tryb.
(Date and place of issue)
6) Pawel Ciechanowski
Product Manager
…………………….………………….. ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
No.
Description of goods
Code
1
Race clock with results option
T6-RCU