Polanik S-250 User manual

INSTRUCTION MANUAL
Competition long jump and triple jump take-off board set
with stainless steel foundation tray lowered edges
and wooden base board
S-250 (ver. 2017)
SAFER JUMPS TECHNOLOGY
File: 2018-01-04
PRODUCT SUPPORT
Pawel Ciechanowski
p.ciechano[email protected]m

Instruction manual S-250 ver. 2017 2/11
Thank you for choosing Polanik competition take-off board.
Contents
Chapter
Page
I. General characteristics
2
II. Parts list (part sets)
3
III. Assembly and installation
4
IV. Remarks on maintenance and operating
8
V. Technical drawing - installed take-off board
9
VI. Additional equipment, available separately
10
VII. IAAF certificate
11
I. General characteristics
The take-off board S-250 is designed for conducting sports events and training programs of horizontal jumps.
Main features of the take-off board:
construction according to the latest safety recommendations –no metal elements in take-off zone, so
foundation tray with lowered edges covered by synthetic surface and white take-off board fastened from
the bottom side, no screws on top
innovative construction –constituted by elements which are easy to assemble, transport and store
easy operating –fast assembly and disassembly processes, which take 15 minutes approx., can be done by
one person provided that the foundation tray is already embedded in the track,
high durability and quality –foundation tray made of stainless steel does not require additional
maintenance actions, other elements are made of plastic, waterproof plywood and impregnated wood, the
take-off board meets the international quality standards
fast replacement of wearing parts and elements

Instruction manual S-250 ver. 2017 3/11
II. Parts list (part sets)
Item
Part/set description
Q-ty pcs
Part/set sketch
1
Stainless steel foundation tray
(lowered edges) with
accessories for concreting
(draining tubes and spacing
boards)
K3-250
1
2
Wood base board
S-250-01-01
1
3
White take-off board with
screws
K1-250
1
4
Indicator plasticine board
S-250-02-00
2
5
Training indicator board
without plasticine
S-250-02-03
1
6
Plasticine 300 g
S-250-02-01
1

Instruction manual S-250 ver. 2017 4/11
Item
Part/set description
Q-ty pcs
Part/set sketch
7
Plasticine forming knife
S-250-06-00
1
8
Wrench - to block the
supporting board in the tray
S-0250-000-00-08-00
1
9
Draining plastic grid
S-250-03-00
3
III. Assembly and installation
The take-off board set is assembled for transport and includes all the mentioned elements. Before first use the
foundation tray (item 1) is to be embedded in the track in the prescribed place, so that the take-off line –the edge of
the white take-off board (item 3) which is closer to the landing pit, is in the distance of:
□1 - 3 m (for long jump) to the landing pit edge that is closer to the take-off line –the IAAF international
competition rules,
□13 m (for men) and 11 m (for women) to the landing pit edge that is closer to the take-off line –the IAAF
international competition rules.
For any other competition, the distance shall be adjusted to competitors` level.
The installation point of the tray (item 1) of the take-off board is presented below.
Drawing no. 1. Installing the take-off board –general view

Instruction manual S-250 ver. 2017 5/11
ATTENSION!
The long side edges (B) of the foundation tray are 13 mm lower, they should be covered by synthetic surface. The
short side edges (A) are to be flash with the top surface of the synthetic surface.
The tray should be positioned in the track and the inside of the tray must be secured with spacing boards (see image
no. 1 and draw. no. 2), so that it does not deform while placing the concrete. Deformations can make the plasticine
board (item 4) or training board (item 5) block inside the tray.
Image no. 1. Installed tray secured with spacing boards

Instruction manual S-250 ver. 2017 6/11
A –foundation tray B –spacing board C –athletics synthetic surface
D –concrete E –ground F –draining tube
Drawing no. 2. Embedding the foundation tray
Draining tubes ought to be positioned vertically in the spaces of the foundation tray and should go past the concrete
layer. During the embedding process of the tray (item 1), draining tubes can stick out over the foundation tray
bottom. After the concrete setting, the sticking tube ends are to be cut off as close to the tray bottom as possible to
ensure the correct water outflow.

Instruction manual S-250 ver. 2017 7/11
To install the take-off board (item 2 and item 3) in the embedded tray (item 1), a flat wrench 24 (item 8) is needed.
The installation begins with placing the plastic
grids (item 9) in the embedded tray (item 1).
Next the base board (item 2) with white take-off
board (item 3) should be positioned on the plastic grids
(item 9), so that the square heads of the adjusting bolts
point the landing pit.
The base board (item 2) with white take-off board (item
3) is secured inside the tray (item 1) by means of the
adjusting plastic bolts, use special wrench 24 included in
the set (item 8). The bolts should be turned
counterclockwise until the perceptible resistance occurs.
When the base board (item 2) with the white take-off
board (item 3) are properly mounted,
the indicator board (item 4 or item 5) can be put into the
tray (item 1).

Instruction manual S-250 ver. 2017 8/11
IV. Remarks on maintenance and operating
Plasticine strips deform during training sessions and competitions. There are two indicator plasticine boards (item 4),
one training indicator board without plasticine (item 5), one plasticine block (item 6) and one forming knife (item 7) in
the set. Thanks to the two indicator boards you are able to replace the one with the deformed plasticine strips with
the other one very quickly. It is recommended that one should substitute plasticine board (item 4) with indicator
board without plasticine (item 5) for intensive training sessions. Training indicator board (item 5) is thinner and does
not require plasticine.
Dents and defects in the plasticine layers should be filled up and leveled. First one ought to apply thick layers of
plasticine on the damaged areas. Then the layers are to be leveled with the forming knife (item 7), as it is shown
below.
Attention! While storing or using plasticine should be protected against high temperatures (over 40 °C), because
otherwise it can change its shape and dimensions, and in extreme cases it can become a liquid.
To ensure great aesthetics and high comfort for jumpers we use natural raw materials like wood and plywood. The
materials are not so durable as synthetic ones. Thus the wooden take-off board parts wear out faster and they need to
be replaced. In order to maintain the parts in good condition all the take-off board elements:
the base board (item 2) with white take-off board (item 3),
the plasticine indicator board (item 4) (or training indicator board (item 5)
plastic grid (item 9)
must be removed from the embedded tray after competitions and training sessions and stored in a dry place. It is
recommended that the embedded stainless steel tray (item 1) should be sheltered with the stainless steel cover
(available separately). Any defects in paint coating revealed during thorough regular inspections of the board set must
be repaired with wood paint or impregnant.
Even though the wooden elements are impregnated and protected with paint, a prolonged contact with water can
devastate or deform them.
The white take-off board (item 3) can be unscrewed, turned over and screwed again to the base board (item 2). That
prolongs significantly the product’s life.
Even the best technical solutions cannot substitute for common sense. The usage of the product must take place
under the supervision of qualified sports arena staff and trainers. The producer shall not be liable for any incidents
caused by the improper take-off board installation, assembly or its misuse.

Instruction manual S-250 ver. 2017 9/11
V. Technical drawing - installed take-off board
a –stainless steel tray (item 1)
b –adjusting bolt
c –plasticine indicator board (item 4)
d –white take-off board (item 3)
e –wooden base board (item 2)
f –athletics synthetic surface
g –concrete
h –plastic grid (item 9)
i –ground
j –draining tube

Instruction manual S-250 ver. 2017 10/11
VI. Additional equipment, available separately
Item
Part/set description
Part/set sketch
1
Stainless steel cover for competition take-off
board
PBN-S0250
Stainless steel cover for take-off competition
boards, secures the inside of the board tray,
smooth surface and 6 adjustable feet (in the
range of 20 mm) for installing synthetic track,
strong ribbed construction. Designed for
sticking tartan.
2
Stainless steel cover with edges for
competition take-off board
PBN14-S0250
Stainless steel cover for take-off competition
boards, secures the inside of the board tray,
special edges for installing synthetic surface,
6 adjustable feet (in the range of 20 mm),
strong ribbed construction, equipped with
edges to facilitate application of tartan.
3
Plasticine straps for indicator board
P8x31
Set of 8 red plasticine straps, specially
shaped, ready to be put into the indicator
board recess, designed for Polanik
competition take-off boards
4
Rubber indicator board for competition board
LG15-250
black full rubber indicator board designed for
training

Instruction manual S-250 ver. 2017 11/11
VII. IAAF certificate