Polanik W-636 User manual

Technical specification
Instruction manual
High jump school landing area
W-636
File: 2014-07-18
Product support
Paweł Ciechanowski
p.ciechano[email protected]

Technical specification/Instruction anual W-636 2/8
Thank you for choosing Polanik landing area.
Safe assem ly and use
•ATTENTION! VACCUM PACKED PRODUCT – UNPACK IMMEDIATELY AFTER DELIVERY
•Before you start to asse ble and use the landing area please read this anual carefully and store the anual in a
safe place for further reference. Polanik Sp. z o. o. shall not be liable for any da ages which are the result of the
failure to follow this anual.
•Unauthorized copying of this anual, in whole or in part, is prohibited.
•The contents of this anual are subject to change without notice.
•Warning! The sports equip ent produced by Polanik Sp. z o. o. is designed for athletics training and use in sports
co petitions only. Please pay special attention when using the product, isuse of athletics equip ent can cause
serious injury or in extre e cases even death. That is why training and use during sports events have to be always
supervised by authorized sports personnel. In no event shall Polanik Sp. z o. o. be liable for any special, incidental,
indirect or consequential da ages in connection with the purchase or use of POLANIK products or costs over the
original cost of the product.
•Specific warranty ter s:
1) The use of the landing area outdoors requires a waterproof cover and a landing area platfor for proper
insulation fro the ground. Failure to follow the above restrictions results in the loss of the warranty rights.
2) The top pad of the landing area is equipped with a spike resistant esh fabric. The esh fabric is designed to
protect the landing area against spikes used by ju pers. While landing and walking on the top pad the spikes
go through the esh fabric and do not da age the surface. One ust not shuffle the spikes on the esh
fabric, because under high crosswise stress caused by oving the spikes without lifting the feet, it ay
happen that the top pad will be torn. The da ages of the top pad caused by careless sliding the pikes on the
top pad surface are excluded fro the warranty and can be re oved in course of payable repair or
replace ent of the landing area ele ents.

Technical specification/Instruction anual W-636 3/8
Contents
Chapter Page
I. General description 4
II. Technical specification 4
III. Packing and transport 5
IV. Preparation for the first use 5
V. Asse bly 5
VI. Operating 6
VII. Maintenance 6
VIII. Storing 6
IX. Declaration 7

Technical specification/Instruction anual W-636 4/8
I. General description
POLANIK landing area W-636 is top quality sports equip ent which is designed to secure ju pers and absorb
i pact energy of a ju per’s landing after take-off and flight in high ju p training.
II. Technical specification
Code W-636
Di ensions length / width / height [ ] 6 / 3 / 0,6
Weight [kg] 230 kg
Nu ber of seg ents [pcs] 4
Spike resistant surface upper surface of top pad is equipped with spike resistant esh fabric
Seg ent covering PVC, ade of polyester with two vinyl layers
Internal structure advanced 3-layer construction, ade of high quality PUR foa
Way of seg ent linking stainless steel hooks and D-rings
Way of waterproof cover linking etal D-rings
Carrying handles very strong jacquard webbing, fir ly attached by eans of envelope
stitching

Technical specification/Instruction anual W-636 5/8
III. Packing and transport
The di ensions* of the vacuu ed packed landing a area seg ents:
Seg. no. Description
Weight [kg]
Length L [ ] Width B [ ] Height H [ ]
01 Top spike resistant pad 51,5 2,00 0,60 0,60
02 Main seg ent 60 1,90 0,65 0,65
03 Main seg ent 60 1,90 0,65 0,65
04 Main seg ent 60 1,90 0,65 0,65
Total volume [m
3
] 3,13
Total gross weight [kg] 231,5
*Please note that the di ensions can differ fro the above table in the range of +/- 7%.
IV. Preparing for first use
The landing area ele ents are vacuu packed only for transport. Please unpack the i ediately after delivery and
leave the in a roofed place for few hours, so that they can return to their original shapes. Storing vacuum packed
landing area elements may cause permanent damages in their internal structures. When the landing area ele ents
return to their original di ensions, you can place the in high ju p field. The field surface should be even, s ooth

Technical specification/Instruction anual W-636 6/8
and without any obstacles. If you use the landing area outdoors, you should also provide: a special waterproof cover
P-636 to protect the landing area against unfavourable weather conditions and a odular platfor SW-6x3 to insulate
the landing area fro the ground.
V. Assem ly
It is done in 5 easy steps:
place the ain seg ents of the landing area in the
high ju p facility,
using the jacquard webbing belts and self-locking
buckles located on the seg ent sides fasten the
seg ents to each other,
place the top pad on the landing area ain seg ents,
then fasten the top pad to the ain seg ents using
the snap hooks and D-rings,
now the landing area is ready for use.
VI. Operating
Stepping on the landing area and practising require special footwear designed for those purposes. Treading on the
landing area in footwear with spikes is only allowed when the landing area is equipped with special spike resistant
surface. Stepping on the landing areas in hard footwear or in shoes with heels is strongly prohibited. You ust not
put any tables, chairs, benches or any other objects whose unit pressure exceeds 1kg/1c
2
on the landing area. If
the landing area is oved fro one place to another very often, it is reco ended that a landing area cart should
be used.

Technical specification/Instruction anual W-636 7/8
VII. Maintenance
Due to the hygiene require ents it is reco ended that the landing area should be cleaned regularly with
co only available detergents. Before you start wiping the landing area, please try to clean a s all spot on its
botto side in order to check the reaction with the PVC fabric.
VIII. Storing
The landing area seg ents can be stored only in a horizontal position. They cannot be bent or pressed by any objects
during storing. That ay defor the seg ents per anently. A storing facility should be clean and dry. It ought to
provide in. te perature 5º C.
Even the best technical solutions cannot substitute for co on sense. The usage of the product ust take
place under the supervision of qualified coaches. The producer shall not be liable for any incidents caused by the
i proper asse bly or its isuse. The producer reserves the right to introduce without warning changes in product
constructions and colours.

Technical specification/Instruction anual W-636 8/8
IX. Declaration
1) No. 2008-08-05
2) Issuer’s na e: POLANIK Sp. z o. o.
Issuer’s address: Życzliwa 11, 97-300 Piotrkow Tryb.
3) Object of declaration:
4) The object of declaration described above is in confor ity with the require ents of the following docu ents:
Docu ent No. Title Edition/Date of issue Position
PN-EN 12503-2 Sports ats – Part 2: Pole vault and high ju p
ats, safety require ents April 2004 All above
Additional Infor ation
5) Declaration for:
BUYER and USER
Signed for and in behalf of:
POLANIK
2014-07-18 Piotrkow Tryb.
(Date and place of issue)
Pawel Ciechanowski
Product Manager
6) ……………………………………… ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
Position Description Code
1 High ju p school landing area 6 x 3 x 0,6 W-636