Polanik PP14-366 User manual

INSTRUCTION MANUAL
Competition steeplechase barrier for water jump
PP14-366
File: 2018-06-04
PRODUCT SUPPORT
Pawel Ciechanowski
p.ciechano[email protected]

Instruction manual PP14-366 2/7
I. General description and use
PP14-366 is a high quality competition barrier, which is designed for water jump in steeplechase race. It is fastened to
the edge of the water jump. The barrier requires concrete foundations. The telescopes, which are protected with
special rubber aprons, guarantee a long product life and an easy operation.
II. Technical specification
Product code
PP14-366
Barrier type
competition, for water jump, fastened to the edge
(A) Top beam
multilayer wooden beam, painted
(B) Telescopes
steel powder painted, spring-loaded knob system of height adjustment, equipped with
special rubber aprons against moisture
(C) Fastening to the track
by means of metal expansion anchors to concrete foundations
Length [mm]
3660
Heights [mm]
762
914
Weight [kg]
83
A
B
C

Instruction manual PP14-366 3/7
III. Assembly
The barrier is designed to be mounted on the synthetic surface of the water jump pit edge, provided that under the
synthetic surface there is a concrete base layer made of concrete class C20/25 or higher and min. 130 - 150 mm thick.
If the base layer does not comply with the mentioned requirements, two foundation blocks are to be made according
to the below diagram.
[mm]
1. the edge of the water jump pit
2. foundation block, minimal dimensions: 500 x 500 x 500 [mm] made of min. C20/25 concrete
To install the barrier to the edge of the water jump pit use the included steel expansion anchors HLC 16x140/90
according to their producer’s instructions (see www.hilti.com). The installation is done in the following way:
1) screw the barrier legs to the top beam with the included screws,
2) position the barrier on the edge of the water jump pit according to the drawing no. 1 and no. 2 (pages 4 and
5), mark the points where to drill the wholes,
3) use the drill bit dia. 16 mm to drill wholes min. 130-150 mm deep,
4) clean the wholes (e. g. with vacuum cleaner)
5) position the barrier on the edge of the water pit,
6) put the anchors into the wholes,
7) screw down the nuts with approximate force 50 Nm.

Instruction manual PP14-366 4/7
a –track surface
b –water level
c –track surface continued under water
d –optional concrete infill for existing water jumps
e –fixed hurdle
f –height for Women
g –height for Men
h –max depth
i –min. depth
j –minimum for adequate strength and protection of
steel from moisture
k –drain
[mm]
Drawing no. 1

Instruction manual PP14-366 5/7
a –track surface
f –height for Women
g –height for Men
[mm]
Drawing no. 2
IV. Operation and maintenance
To change the height please pull the knob and lift (or lower) both sides of the top
beam simultaneously till the height catch blocks.
Attention! The rubber aprons of the telescopes are coated with a long lasting
protection film against UV radiation during the production process, in order to
maintain a proper condition of apron rubber UV protection agents should be
regularly applied on them.
During idle periods the barrier must be stored in a roofed dry place. After every
athletics season the barrier must be cleaned from sand (mud, dust and etc).

Instruction manual PP14-366 6/7
V. Packing and transport
The product is packed in cardboard and foil. The product needs to be assembled.
VI. Product images
PP14-366 © 2018 Polanik
The producer reserves the right to introduce without warning changes in product constructions and colours.
Package’s dimensions [cm]
contents
1 barrier
length
410
width
17
height
30
Volume [ m3]
0,21
Gross weight [kg]
86

Instruction manual PP14-366 7/7
VII. IAAF Certificate