Polaris Hilux Maxx User manual

1
Installaon manual
Navigaon & User manual: Available to
download from:
www.polarisgps.com.au

2
Thank you for purchasing the Hilux Maxx.
Before operaon, be sure to thoroughly read these instrucons.
Warranty for this product is 3 years from date of purchase, however warranty will
be void if:
• The unit is tampered with, damaged or modied in anyway
• If applicable Reverse camera cable is cut or modied in any way
• If applicable Reverse camera is subjected to over voltage
• If applicable the Navigaon SD card is damaged or tampered with in any way (this
includes installing foreign mapping or soware onto the SD card)
• The installaon of 3rd party apps that may cause harm to the unit
Warranty Terms
The Hilux Maxx is covered for 3 years and includes:
• Defecve Equipment • Defecve Cables
Not Covered under warranty:
• Abuse
• Improper installaon
• Alteraon to Cables (includes cung of any cables)
• Accidents
• Water damage
• Improper use
• Labour
• Postage and Handling
• Malicious Soware caused by installing 3rd party apps
If you have any quesons concerning the installaon, warranty or the operaon of the
unit, please contact Polaris on 1300 555 514.

3
Warranty 2
What’s in the box & Power Harness 4
Wiring Diagram 5
Installaon Notes 6
Pulling fascia and trims o 7-10
Pulling the OEM Head unit out 11
Removing brackets from OEM fascia and head unit 11
Aaching Hilux Maxx to OEM bracket and fascia 12
Plugging Hilux Maxx into factory plugs 13
OEM Hilux reverse camera 13
Polaris / Aermarket reverse camera wiring diagram 14
Addional camera wiring diagram 14
3 Camera operaon wiring diagram 15
Bluetooth microphone cable 16
Pung the fascia and trim back together 16
Finished product and steering wheel controls 17
Table of Contents
Please note: once the unit is installed you can access your user manual on the head unit or you
can download a copy from our website: www.polarisgps.com.au
Record your serial number here and keep on hand for future records:

4
What's in the Box & Wiring Diagram
1) Hilux Maxx Unit.
2) Toyota Hilux Patch Loom
3) GPS External Antenna.
4) External Bluetooth Microphone.
5) RR,RL,FR,FL Aud Out & SUB / VID out 1&2 cable.
6) VID in / AUX L / AUX R cable.
7) CAM in / Front CAM IN cable.
8) 2 x USB cables / Bluetooth mic input cable.
9) Polaris Reverse Camera with RCA adaptor.
Power Harness
Connects to
Hilux Maxx
RCA plugs
Red RCA: AUX in R
White RCA: Aux in L
Yellow RCA plugs: Cam in
5 pin plug— Rear Speakers: plugs into OEM Harness
8 pin plug— Main power + Front speakers: plugs into OEM harness
Brown Wire—Key 1
Brown Wire with black stripe—Key 2
Black wire—Ground
Blue wire with white stripe—Amp Control
Notes: Key 1, Key 2 and Gnd wire not needed unless you want to program in your
steering wheel controls. Otherwise the steering wheel controls all run through the
canbus module and do not need programming in.
7 pin plug— Older style Toyota Reverse Camera input (generally not used for current model Hilux)
Notes about wiring in the OEM Toyota Reverse Camera:
Just plugging the Original Toyota reverse camera into the 6 pin plug is not
enough to get the camera working. Please make sure you ALSO plug the Cam in
RCA plug coming from that parcular plug into the Cam in RCA input that plugs
into the back of the Hilux Maxx.
Canbus Module
15 pin plug—steering wheel controls, reverse trigger + more: plugs into OEM harness.
6 pin plug— Hilux OEM Reverse Camera input (generally used for current model Hilux)

5
Wiring Diagram

6
 The wiring and installaon of this unit requires special technical skill and experience. If you do
not feel condent installing this product or do not have the level of skill necessary, please
contact Polaris on 1300 555 514 so we can refer to a recommended installer.
 This unit is designed to be used in a vehicle with a 12 volt baery and a negave grounding.
Before installing this unit to a recreaonal vehicle, bus, or truck, make sure the baery
voltage is appropriate for this unit to be used. If installing into a 24Volt vehicle , you will need
a 10 amp converter which can be purchased through automove electronic shops such as
Jaycar electronics.
 To avoid short circuit in the electrical system, ensure that the negave baery cable is
disconnected before installaon.
 To avoid possibility of shorng out the electrical circuit in the unit, never connect the baery
wire directly to the vehicle baery.
 Always secure all wirings with cable clamps or adhesive tape to prevent short circuit.
 Please make sure all wiring connecons and speaker wires are well insulated.
 When pulling the dash apart, please use quality trim tools to avoid damaging your dash.
 Please do NOT cut any plugs o of any Polaris cameras. Doing so will void your warranty! If
you need to blend other brand cameras into our system, please call Polaris on 1300 555 514
so we can refer you to a recommended dealer who has the skill and experience in performing
this type of work.
 If you want an aermarket reverse camera to trigger when reverse gear is engaged, you will
need to nd reverse power. Please see page 14 for aermarket reverse cam wiring
instrucons or page 4 For OEM reverse camera wiring instrucons
 If there is something you are not 100% sure about when installing this unit, please give our
experienced technicians a call on 1300 555 514.
 You shouldn't be required the programme in the steering wheel controls as the power harness
has a canbus module built in. The canbus module is what controls the steering wheel control
funcons so they should work from the get go provided that everything has been plugged in
correctly.
Installaon Notes

7
Start by removing the two plasc screws in the gauge
housing with a stubby screw driver.
Gently Pull at both ends of the gauge housing to pop it
out. Remove and set aside.
The following installaon pictures have been taken using
the Hilux Maxx head unit. The same principle applies when
removing the factory head unit.

8
With your ngers, gently pry open the long dash trim
panel above the radio gradually working your way
down unl it’s completely removed.
Now open the boom glovebox so that you can grab
the top glovebox. Gently pull it out and put aside.

9
Next is the air condioning control panel. Get your
ngers in behind the panel, pull forward to pop it out
and let it sit there.

10
There are 4 screws that need to be undone (use a
10mm / phillips head), two up the top and two down
the boom. Once they are all out, pull on the fascia
and pop it forward.