Polaris TITAN 2882799 User manual

APPLICATION
Verify accessory fitment at Polaris.com
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
KIT CONTENTS
This Kit includes:
REF QTY PART DESCRIPTION PART NUMBER
1 1 Auger Mount - Front 1023651
2 1 Auger Mount - Rear 1023652
3 1 Auger Carrier - Rear 1023844
4 1 Auger Carrier - Front 1023845
5 2 Hitch Pin 1023795
6 1 Auger Mount Plate 5264835
7 1 Strap Plate - Rear LH 5264841
8 2 Screw - M8 X 1.25 X 40 7518178
9 4 Screw - HXFL - M6 X 1.0 X 20 7520122
Instr 9927953 Rev 01 2017-07 Page 1 of 8
P/N 2882799
TITAN™™ ICE AUGER RACK KIT

Instr 9927953 Rev 01 2017-07 Page 2 of 8
REF QTY PART DESCRIPTION PART NUMBER
10 2 Screw - SPCL - M6 X 1.0 X 20 7520464
11 6 Nut - M6 X 1.0 7547453
1 Instructions 9927953
TOOLS REQUIRED
• Safety Glasses
• Socket Set, Metric
• Wrench Set, Metric
• Socket Set, Torx®Bit
• Torque Wrench
IMPORTANT
Your Titan™Ice Auger Rack Kit is exclusively designed for your vehicle. Please read the installation instructions
thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to
ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.
ASSEMBLY TIME
Approximately 30 minutes
NOTE
Additional time may be required for optional steps, or
to accommodate other installed accessories.
INSTALLATION INSTRUCTIONS
COMPONENT REMOVAL
1. Remove tail light Aby removing two screws B
and unplugging tail light from harness. Set aside
for later use.
2. Remove rear cargo platform Cby removing ten
screws D.
3. Remove rear rack support Eby removing six nuts
F.

Instr 9927953 Rev 01 2017-07 Page 3 of 8
4. Your vehicle is equipped with an aluminum
template Gthat has pre-drilled holes in it that will
need to be removed.
NOTE
The template holes are used to locate the bolts for
the rear rack support and the ice auger rack kit.
INSTALLATION
1. Place provided bolts ainto T-slot and slide them
into the approximate location as shown.
2. Reinstall template making sure tabs are into the
opening in the T-slot and newly place bolts are
aligned with the holes in the template.
3. Place the front auger mount qonto the two new
bolts installed in the previous step. Loosely fasten
nuts sso that the support bracket is held in place
but do not tighten.
4. Install the auger mount plate yaround the
running board tube support and onto the front
auger mount qusing supplied screws oand
locking nuts sas shown. Torque all six locking
nuts sto specification provided.
TORQUE
8.5 Ft. Lbs. (12 Nm)

Instr 9927953 Rev 01 2017-07 Page 4 of 8
5. Reinstall the rack support Eand torque all six
mounting nuts Fto specification provided.
TORQUE
8.5 Ft. Lbs. (12 Nm)
6. Reinstall the rear cargo platform Cto the rear rack
support using the ten existing fasteners D
previously removed and torque to provided
specification.
NOTE
Make sure your tail light harness plug is accessible
to install tail light in next step.
TORQUE
8.5 Ft. Lbs. (12 Nm)
7. Plug in tail light connector and install tail light A
using original fasteners Bbeing careful not to
overtighten.
8. Install rear auger carrier mount using supplied two
screws ias shown. Torque to specification
provided.
NOTE
If your vehicle is equipped with the optional rear
bumper handle kit, PN 2882803, you will need to
remove the handle on the left side before installing
the rear auger mount.
TORQUE
25 Ft. Lbs. (35 Nm)

Instr 9927953 Rev 01 2017-07 Page 5 of 8
9. Install the front auger carrier assembly rinto front
auger mount qand secure into position using
supplied hitch pin t.
10.Install the rear auger carrier assembly einto rear
auger mount wand secure into position using
supplied hitch pin t.
11. Place auger onto front and rear mount with the
powerhead of the auger towards the front of the
machine and ensure that the auger shaft is fully
seated into the front and rear V-groove supports.
NOTE
The Titan Ice Auger Carrier Kit comes assembled to
accept augers that operate in a clockwise (right
hand) rotation. If your auger operates in a
counterclockwise (left hand) rotation you will need to
replace the standard rear strap plate Hwith the
optional LH rear strap plate uthat was supplied with
your kit. See Step 11a-11c for installation of the
optional LH rear strap plate.
a. To install the LH rear auger strap plate, PN
5264841, remove the fasteners J/Kholding
the RH rear auger strap plate assembly in
place.
NOTE
You will need to remove the strap Land latch
mechanism Mfrom the standard rear auger strap
plate and install onto the LH rear auger plate strap.

Instr 9927953 Rev 01 2017-07 Page 6 of 8
b. Remove the standard rear auger strap plate H
and install the optional LH rear strap plate u
as shown. Torque fasteners to specification
provided.
TORQUE
18 Ft. Lbs. (24.5 Nm)
c. Reinstall the strap Land latch mechanism M
onto the LH rear auger strap plate. Torque
fasteners to specification provided.
TORQUE
7 Ft. Lbs. (9.5 Nm)
12.After confirming the correct rear auger plate is
installed you may need to adjust the front auger
carrier powerhead support Nto prevent the
powerhead from rotating while in transit. To do so,
loosen the front auger strap plate locking nuts K
and adjust the powerhead support until it makes
contact with the powerhead. Re-torque fasteners
to specification provided.
TORQUE
18 Ft. Lbs. (24.5 Nm)
13.Ensure all tools are accounted for and all steps
have been completed.

Instr 9927953 Rev 01 2017-07 Page 7 of 8
AUGER SECUREMENT
WARNING
When transporting your ice auger you must ALWAYS
secure it into place using the provided strap and
latching mechanism. Failure to comply may result in
serious personal injury or death.
Once auger carrier rack is installed and adjusted
correctly, place auger into carrier and secure the
auger into place using the auger hold down
mechanisms by placing the strap over the top of the
auger and inserting the strap Linto the latching
mechanism Mon the opposite side of the auger shaft.
After inserting the strap into the latching mechanism,
tighten the straps by ratcheting the latching
mechanism until the strap is firmly holding the auger
in place.
IMPORTANT
Use caution to avoid overtightening the latching
mechanism M. Excessive force may damage the
latching mechanism.
.

Instr 9927953 Rev 01 2017-07 Page 8 of 8
FEEDBACK FORM
A feedback form has been created for the installer to provide any comments, questions
or concerns about the installation instructions. The form is viewable on mobile devices
by scanning the QR code or by clicking HERE if viewing on a PC.
FEEDBACK FORM