Champ 4031 User manual

Auto Body Toolmart
Champ Frame Straightening Equipment, Inc.
www.autobodytoolmart.com
2545 Millennium Drive,Elgin, IL. 60124 [phone]
4031 Universal Parts Stand
Read all assembly instructions completely before attempting to assemble unit.
Improper or incomplete assembly could result in damage to Universal Stand or injury to user.
WARNING
1-A 2-A
4-A
5-A
Frame Straightening Equipment Inc.
Made In USA
Parts List
3-A
6-A
7-A
8-A
Part Quantity
Support Base - .1
1-A - . . . . . . . . .1
2-A - . . . . . . . . .1
3-A - . . . . . . . . .1
4-A - . . . . . . . . .2
5-A - . . . . . . . . . 2
6-A - . . . . . . . . .1
7-A - . . . . . . . . .1
8-A . . . . . . . . . .2
Automotive

Insert the 1-A about 6” down the center of the
base and tighten the bolt.
Insert the 3-A onto the center of the base. Connect each 4-A into both sides of the 3-A
and tighten the bolts.
Insert an 8-A into each bar jetting out from
the bottom of the base. Place the 2-A in the 1-A as shown above.
1. 2.
3. 4.
5. 6.
Adjust the chain on both sides of the base to
get the desired length.

Insert the 7-A on one of the 4-A’s.
Finally, on the 4-A that is not holding the
7-A, attach the 6-A. The Universal Parts Stand is ready to be
used. Shown holding two fenders
7. 8.
9. 10.
11. 12.
Add a 5-A to each side of the 4-A.
The Universal Parts Stand is capable of holding mirrors, panels, bumpers, door handles, fenders & more.
Mounting a Side Mirror Mounting a Spoiler

Mounting
Bolts
13. 14.
15. Mounting a spoiler
Mounting a door handle

Part Quantity
Auto Body Toolmart
Champ Frame Straightening Equipment, Inc.
2545 Millennium Drive, Elgin, IL. 60124 [phone]
4032 Universal Part Stand
Read all assembly instructions completely before attempting to assemble unit.
Improper or incomplete assembly could result in damage to Universal Stand or injury to user.
WARNING
1-M
2-M 3-M 4-M
5-M
Frame Straightening Equipment Inc.
Made In USA
Parts List
6-M 7-M
9-M 10-M
8-M
All parts are labeled
Motorcycle
Support Base - .1
1-M - . . . . . . . .1
2-M - . . . . . . . .2
3-M - . . . . . . . .1
4-M - . . . . . . . .2
5-M - . . . . . . . . 4
6-M - . . . . . . . .1
7-M - . . . . . . . .1
8-M . . . . . . . . . .1
9-M - . . . . . . . .1
10-M - . . . . . . .3

Insert the 1-M about 6” down the center of the
base and tighten the bolt.
Insert the 3-M onto the center of the
base. Connect each 4-M into both sides of the 3-M
and tighten the bolts.
Insert each 2-M into both sides of the 1-M
and tighten the bolt on the 1-M. Place the 9-M onto one of the bars jetting out
from the bottom of the base.
1. 2.
3. 4.
5. 6.
Adjust the chain on both sides of the base to
get the desired length.

On the same side, add part number 7-M.
Insert the 8-M and tighten the bolt. On the opposite side, insert the large 5-M
followed by a smaller one. Remember, the
height is adjustable on all of the 5-M’s.
The 5-M is followed by the 6-M. The
height is adjustable on the 6-M. Insert the remaining 5-M and add the 10-M’s.
7. 8.
9. 10.
11. 12.
On the opposite side of the 10-M, place one
of the small 5-M’s onto the 4-M. The height
of the 5-M’s are adjustable.

Mounting
Bolts
13. 14.
15. 16.
17. 18.
The Universal Parts Stand is ready to be
used. Parts are adjustable to hold all types of
motorcycle parts.