Polaroid T-64 User manual

Description
Special tungsten (3200°K) balanced film for rich, saturated color
prints, in 31/4 x 41/4pack format. Color-balanced for tungsten
lighting, rich and saturated colors, excellent image sharpness
and clarity, designed for long exposures (ideal @ 1/2to 30
seconds).
Key Applications
•Professional photography (proofing for tungsten studios)
•Copystand photography
•Microscopy
• Scientific imaging
Compatible Hardware
•MP-4+ camera
• Any camera or instrument (especially microscopes) equipped
with a Model 405 film holder
Special Treatment
None
Film Data Sheet
T-64
Tungsten Pack Film
Film Speed
ISO 64/DIN 19
Format
31/4x 41/4 in. (8.5 x 10.8 cm)
Pack Film
Image Area
27/8x 33/4in. (7.3 x 9.5 cm)
Finish
Glossy
Exposures per Unit
10 exposures per pack
Development Time
90 seconds at 70°F
&RORU,QVWDQW3DFN)LOP


[

LQFK
[FP
ILOP
7
7\SH
Caution
This film uses a small amount of caustic paste. If any paste appears, avoid contact with skin, eyes and mouth
and keep away from children and animals. If you get some paste on your skin, wipe it off immediately, then
wash with water to avoid an alkali burn. If eye contact occurs, quickly wash the area with plenty of water and
see a doctor. Keep discarded materials away from children, animals, clothing and furniture.
Limited Warranty
See information on the film box.
“Polaroid” and “Polacolor” are trademarks of Polaroid Corporation, Waltham, MA 02145 USA.

Processing time and temperature
For best results process at temperatures
above 60oF(16oC).
The information in this film data sheet
represents the typical performance of
Polaroid’s T-64 Tungsten color films.
Specific film lots may vary.
Film Data Sheet
Technical Data
T-64 Tungsten
Instant Color Peel-Apart Films
D-Max: The density value for
the film’s darkest black.
D-Min: The lowest density
value that a film exhibits. In
prints, the whiteness of the
brightest highlight, relative to
the unprocessed print.
Slope: The positive ratio of the
log E increments of the straight
line region of the curve, as
determined by the 1/4-3/4
increment method. The slope
of an H&D curve indicates the
overall contrast of a film: low
contrast slopes less than 1.10;
medium contrast slopes from
1.10 to 1.70; high contrast
slopes greater than 1.70.
Recommended
speed (ISO) 64 / 19o
Recommended
processing time
and
temperature
90 sec. @
70oF/21oC
Resolution
(1000:1) 10 line
pairs/mm
Contrast Medium - High
0
-2 -1
0
1
2
Relative Log Exposure
3
Sample Density
-3
H&D Curves @ 70
o
F/21
o
C
Characteristic H&D curves for
normal development
Blue
Red
Green
Sample Density
Relative Log Exposure
-3 0-2 -1
0
1
2
3
Blue
Red
Green
H&D Curves
@ 55
o
F/18
o
C
Characteristic curves for
cold development
Sample Density
Relative Log Exposure
-2-3 -1
0
1
2
3
Blue
Red
Green
0
H&D Curves
@ 95
o
F/35
o
C
Characteristic curves for
hot development
oFoCTime in
seconds Exposure Adjustment
95 35 90 -1/3 stop
65-90 21-32 90 None
55 13 120 1/2 stop

Reciprocity law failure
A wide range of shutter speeds can be used without loss of film speed.
For longer exposure times, some exposure compensation is suggested.
Film Data Sheet
Technical Data
T-64 Tungsten
Instant Color Peel-Apart Films
Reciprocity: The ability of the film to respond in a constant
manner to a constant exposure (light intensity x time).
Reciprocity failure occurs during very long or very short
exposures, requiring the photographer to increase exposure.
Spectral Sensitivity: Shows the equivalent energy needed
at each wavelength in order to activate the emulsion so that it
produces a neutral density of .75.
Shutter
Speed 1/4000 to 1/30 1/15 to 4 8 16 32 64
Exposure
Adjustment Not
recommended +2/3 stop None +1/3 stop +1/3 stop +1/3 stop
Color
Compensating
Filter - None None None CC05B CC05B
Exposure Time (seconds)
Relative Log Exposure
.001" .01".0001" .1" 10"1" 100"
Reciprocit
y
Law Failure
0
.2
.4
.6
.8
1.0
1.2
1.4
1.6
1.8
Blue
Red
Green
Spectral Sensitivity
Wavelength (nm)
0
1
10
1000
Spectral Sensitivity
350
100
650600550500450400 700
Blue
Red
Green