Polygroup PF5620 User manual

1
Use of the 1.25” to 1.5” Hose Adapter
1. 1.25 " to 1.5 " Hose Adapter is shown below:
2. Installation Procedure:
* Filter pump image for reference only
1) Take out the Filter Pump Assembly, two Hoses, four Hose Clamps and
four Hose Adapters.
2) Add a Hose Clamp on each end of the hose. Insert a Hose Adapter
to one end of the hose and then, connect the hose to the Filter
Pump Inlet.
3) Insert another Hose Adapter to the other end of the hose and then,
connect the hose to the Suction Fitting of the pool.
4) Tighten the Hose Clamps to prevent loosening and water leakage.
Repeat steps 2, 3 & 4. Connect the Return Fitting to the Filter
Pump Outlet (sequence as shown below).
If the diameter of the Filter Pump Inlet/Outlet or Pool Fittings (1.25") do not match with the diameter of the hose (1.5"),
take out the Hose Adapters from the accessories pack and follow the steps below for installation.
Note: These instructions are only applicable if the Hose Adapters are included in the accessories
pack of the filter pump packaging.
Key #
1
PART #Description
Hose Adapter x 1 P58PF5620P01
Replacement parts ordering info
a.
b.
a.
b.

OWNER’S MANUAL
2
* Filter pump image for reference only
Use of the Universal Adapter
1. If the suction fitting and return fitting of your pool are the plunger valve type (as shown in diagram below), you can use the Universal Adapters to fit the
plunger valves with the hoses that come with the Polygroup®filter pump. Follow the installation procedure below:
2. Installation Procedure:
Note: These instructions are only applicable if the Universal Adapters are included in the accessories
pack of the filter pump packaging.
Key #
1
PART #Description
Universal Adapter x 1 P58003689W05
Replacement parts ordering info
1) Take out the Filter Pump Assembly, two Hoses, four Hose Clamps and
two Universal Adapters.
2) Attach one Universal Adapter to each plunger valve of the pool
respectively.
3) Connect the 1.25" or 1.5" hose to the adapter, then tighten the hose
clamp.
4) Connect another hose to the other adapter, then tighten the hose
clamp.
O-ring for 1.5" hose
O-ring for 1.25" hose
Gasket
Universal Adapter

3
Upgrading the SFX Skimmer Plus
Filter System to a Sand Filter or
RX Cartridge Filter System
Tips: This instruction is only applicable if the accessories pack includes the seal plate.
Only use the seal plate when you need to upgrade the existing SFX Filter system to a Sand Filter or
RX Cartridge Filter system.
To replace your existing SFX Filter to a Sand Filter or RX Cartridge Filter, simply assemble the new filter
according to the following instructions.
1. Unpack the new filter that you have purchased, and take out the round Seal Plate included (as in below diagram).
2. Replace the SFX Motor with the Seal Plate following the steps shown below:
6) Remove the SFX Motor Assembly, and seal the Canister opening
with the Seal Plate. Fasten the Motor Seal Nut tightly to ensure
that no water leaks.
4) Remove the Top Cover, Strainer Basket, and Filter Cartridge.
Use a water container (e.g. a bucket, not included) to collect
the purged water resulting from servicing the pump.
1) Unplug the power.
2) Insert the Water Stopper into the pump’s water intake. Push the
stopper tightly into the Skimmer Seal Ring.
3) Detach the Locking Ring and RF Diverter by turning it
counterclockwise. Insert the Service Plug.
Water Stopper
Skimmer Seal Ring
RF Service Plug
Locking Ring
RF Diverter
Top Cover
5) Remove the Motor Seal Nut by turning it clockwise. Do not pull
or push the canister, as this can cause damage between the
canister and pool liner.
Motor Seal Nut
Rubber
Nozzle
Round Seal Plate
Motor Assembly
Motor
Seal Nut

OWNER’S MANUAL
4
3. Assemble the Sand Filter or RX Cartridge Filter System according to its instruction manual.
4. Install your new filter to the SFX Canister as indicated below:
5. Refer to the instruction manuals and make sure that all connections are firmly secured.
6. Plug in the Sand Filter or RX Cartridge Filter System, and enjoy!
WATER OUT
WATER IN
SFX
POOL
RX CARTRIDGE FILTER SYSTEM
WATER OUT
WATER IN
SAND FILTER
Key #
1
PART #Description
Seal Plate x 1 P5810170AE01
Replacement parts ordering info