Polygroup GD4000CYKD00 User manual

Part
1
2
3
Description
Section 1
Section 2
Eye bolt (preassembled with wreath)
Quantity
1
1
4
Congratulations on purchasing your new wreath from Polygroup®!
Carefully follow the instructions below on how to quickly and easily set up your new wreath.
1. Fasten the eye bolts of section 1 to section 2.
2. Fasten the eye bolts of section 2 to section 1. Connect the
plug of the section 2 to the end-connector of sector 1.
3. Shape and shift wreath branches to fill in any gaps. Plug
the adapter from section 2 into a wall outlet.
MODEL #: GD4000CYKD00
WREATH ASSEMBLY INSTRUCTIONS
*Electrical Rating For The Wreath
(For Indoor and Outdoor Use)
Input: 120V, 60Hz, 0.16A
Output: 29V DC 0.28A
PACKAGE CONTENTS
1
1
section
100 Lights
1
End-connector
Plug
100 Lights 100 Lights
Screw the eye bolts attached
through the hole and tighten.
2
section
1
section
2
End-connector
Plug
Insert Green
Label Extension
Cord into Adapter
Adapter
To Be Plugged
Into Wall
Outlet
Control box
Eye bolt (preassembled
with wreath)
STORAGE INSTRUCTIONS:
1. Remove all ornaments and decorations.
2. Disconnect from power source.
3. Detach all light plugs. Then disassemble wreath sections
from each other by loosening the eye bolts.
4. Store your wreath in a cool, dry place away from sunlight.
Exposure to excessive heat or humidity may damage the
wreath.
NEED HELP?
DO NOT RETURN TO STORE. PLEASE VISIT US AT:
www.polygroupstore.com OR 1-888-919-0070

2
TROUBLESHOOTING TIPS
If Wreath Does Not Illuminate
1. Please check to make sure that all plugs are properly connected according to the color labels and the adapter is plugged into
the wall outlet. Refer to assembly guide for instructions.
2. Please check for loose, broken or missing light bulbs and replace as needed.
Simply press the selector button to select from the following light functions:
(1) CLEAR-MULTI: FADING (2) CLEAR: FADING
(3) CLEAR-MULTI: ALTERNATING (4) CLEAR: STEADY
(5) CLEAR-MULTI: SLOW FADING (6) MULTI: STEADY
(7) MULTI: FADING (8) COMBINATION
DUAL COLOR LIGHT CONTROLLER & REMOTE CONTROL
Remote
Control Light
Controller
Selector Button
Insulation Tab
REMOTE CONTROL INSTRUCTIONS
1. Remove the insultation tab of the remote control.
2. Press either selector button and wait for a second to enjoy light effects in the following sequence (see DUAL COLOR LIGHT
CONTROLLER & REMOTE CONTROL).
2. Replace the used battery with a new CR2032 button cell battery (not included). Make sure that the battery is installed with the
correct polarity (+ and -).
3. Retighten the screw to close and secure the battery cover.
Cover
Battery
CR2032
BATTERY REPLACEMENT
1. Loosen the screw of the battery cover with a screwdriver (not included).
WARNING
1. Dispose used battery properly. observe local regulations regarding disposal of hazardous waste.
2. Ensure the batteries are installed correctly with regard to polarity (+ and -).
3. This product is powered by a lithium battery. Due to their small size, lithium batteries can easily be swallowed by children.
Ingestion of such batteries has been known to cause death.
4. Do not expose light set to moisture.
5. Remove batteries when not used for an extended period of time, or when depleted.
6. Clean the battery contacts prior to battery installation.
7. The external flexible cable or cord of this luminaire cannot be replaced; If the cord is damaged, the luminaire shall be destroyed.
8. Dispose of used batteries properly, and local laws and regulations regarding the disposal of hazardous waste.
9. Use only CR2032 batteries for the remote controller.
10. Do not dispose of batteries in fire. Batteries may explode or leak.
11. This is a lithium battery which if swallowed has been known to cause death.
12. Small parts, keep batteries out of reach of children.

3
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact us at 1-888-919-0070
or visit our website at www.polygroupstore.com. One of our customer service representatives will be happy to assist you.
CUSTOMER SERVICE FOR CHRISTMAS WREATHS
Wreath ID#:
Wreath UPC#:
Store Purchased:
Specify Problem:
Customer Name:
Address(No P.O. Boxes):
City & State:
Zip Code:
Day Phone:
Date Purchased:
Wreath ID# IS LOCATED ON END PANEL OF BOX.Wreath ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
CAUTION:
To reduce the risk of fire and electric shock:
a) Use only the power supply that was provided with this product.Using a different adapter will damage the lights and may cause
fire, or electrical shock hazards.
b) Do not install on trees having needles, leaves or branch covering of metal or materials which look like metal.
c) Do not mount or support strings in a manner that can cut or damage wire insulation.
This product includes spare bulbs.
If extra parts are needed, please contact our customer service center.
SPARE PARTS