Pop-A-Shot PRO I SINGLE User manual

PRO ΙSINGLE
SKU# PASPRO19-01 WWW.POP-A-SHOT.NET

PARTS LIST
Rear Vertical Tube, Middle Rear Vertical Tube, Bottom
Front Vertical Tube, Bottom Horizontal Tube Upper Side Tube, Rear Upper Side Tube, Front Lower Side Tube, Rear
Lower Side Tube, Front
Rim
Control Panel
Pump Rim Bolt Rim Washer Rim Nut Scoring Bolt
Screws
Balls Short Screw
Parts #17, #18 and #21
are in brown box
Long Screw Washer
Rim Net
Scoring UnitSensors AC Adapter Ball Return Ramp
Lean Bar Braces Backboard
Front Vertical Tube, MiddleFront Vertical Tube, Top
Rear Vertical Tube, Top
x2 x2 x2
x2 x4 x2 x2 x2
x2
x1
x1
x1 x4 x8 x4 x4
x4 x18 x16 x34
x2 x1 x1 x1
x1 x4 x1
x2x2
12345
678910
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31
x8
x1
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 2/14

FRAME ASSEMBLY
POP-A-SHOT®PRO SINGLE
12
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 3/14

Connect a Front Vertical Tube, Top (#4) to a
Front Vertical Tube, Middle (#5) and tighten with a
Short Screw (#23) and Washer (#25) (Fig 1A).
Connect the other end of the Front Vertical Tube, Middle (#5)
to the Front Vertical Tube, Bottom (#6) and tighten with a
Short Screw (#23) and Washer (#25)(Fig 1A).
Repeat with the other 4, 5 and 6 tubes.
Connect a Rear Vertical Tube, Top (#1) to a
Rear Vertical Tube, Middle (#2) and tighten with a Short Screw (#23)
and Washer (#25) (Fig 2A).
Connect the other end of the Rear Vertical Tube, Middle (#2)
to the Rear Vertical Tube, Bottom (#3) and tighten with a
Short Screw (#23) and Washer (#25).
Repeat with the other 1, 2 and 3 tubes.
STEP 1
STEP 2
Fig 1A
Fig 2A
6
5
4
1
2
3
23
23
25
25
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 4/14

Connect an Upper Side Tube, Rear (#8) to an
Upper Side Tube, Front (#9) and tighten with a
Short Screw (#23) and Washer (#25).
Repeat with the other 8 and 9 tubes.
Connect the Lower Side Tube, Rear (#10) to the
Lower Side Tube, Front (#11) and tighten with a
Short Screw (#23) and Washer (#25).
Repeat with the other 10 and 11 tubes.
STEP 3
STEP 4
8
23
25
9
10
11
25 23
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 5/14

Attach an Upper Side Tube, Rear (#8) to a
Rear Vertical Tube, Top (#1) using a
Long Screw (#24) and Washer (#25).
Repeat with the other 8 and 1 tubes.
Attach an Upper Side Tube, Front (#9) to a
Front Vertical Tube, Top (#4) using a
Long Screw (#24) and Washer (#25).
Repeat with the other 9 and 4 tubes.
STEP 5
STEP 6
Opposite side view
25
25
25
1
8
9
4
24
24
Opposite side view
25
24
24
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 6/14

6
25
24
Attach a Lower Side Tube, Front (#11) to a
Front Vertical Tube, Bottom (#6) using a
Long Screw (#24) and a Washer (#25).
Repeat with the other 11 and 6 tubes.
STEP 7
STEP 8 Attach a Lower Side Tube, Rear (#10) to a
Rear Vertical Tube, Bottom (#3) using a Long Screw (#24)
and Washer (#25).
Repeat with the other 10 and 3 tubes.
3
10 24
25
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 7/14
11

Attach a Horizontal Tube (#7) to both Front Vertical Tubes, Middle (#5)
using Long Screws (#24) and Washers (#25).
Attach another Horizontal Tube (#7) to both
Front Vertical Tubes, Bottom (#6) using
Long Screws (#24) and Washers (#25).
STEP 9
Attach a Horizontal Tube (#7) to both Rear Vertical Tubes,
Bottom (#3) using Long Screws (#24) and Washers (#25).
STEP 10
Attach another
Horizontal Tube (#7) to both
Rear Vertical Tubes, Top
(#1) using Long Screws (#24)
and Washers (#25).
24
25
24
25
7
5
5
24
25
24
25
7
6
6
24
25
7
2
1
1
2
3
3
7
24
25
24
25
24
25
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 8/14

Attach the Braces (#13) to the four bottom corners using
Short Screws (#23) and Washers (#25).
STEP 11
Loop the Rim Net (#15) through the Net Hooks on the Rims (#16).
Make sure the longer strands are on top and go through the net hooks.
Attach the Rim (#16) to the Backboard (#14) using a Rim Bolt (#27)
and a Rim Washer (#28) on the front and a Rim Washer (#28) and
Rim Nut (#29) on the back.
STEP 12
25
25
25
23
25
23
23
23 13
14
16
27
28
29
28
15
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 9/14

14
Attach the Sensors (#17) using the Screws (#31) (Fig. 10A). Plug the upper sensor cord
into the “Left” outlet and the lower sensor cord into the “Right” outlet on the Scoring Unit (#18).
The wire will go out of the left side of the Top Sensor, and will go out of the Right of the
Bottom Sensor (Fig. 10B).
Note: The Sensors
must be attached level
(Fig 10B) and screwed all
the way into the Backboard
(Fig 10C).
Fig 10C
Put 4 AA Batteries into Scoring Unit (#18) and/or plug in AC Adapter (#19) to Scoring Unit (#18).
Attach the Scoring Unit (#18) to the Backboard (#14) with a shorter Bolt (#30)
through the front of the Backboard and the Scoring Unit.
30
18
18
STEP 13
Fig 10B
AC Adapter
31
Fig 10A
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 10/14

STEP 14
24
24
25
25
Tip: If you can, grab a helper for this part.
Attach the Backboard (#14) to the Rear Vertical Tubes, Top (#1)
using Long Screws (#24) and Washers (#25).
14
1
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 11/14
24
25
24
25
1

STEP 16
STEP 15 Attach the Lean Bar (#12) to the Front Vertical Tubes,
Bottom (#6) using Short Screws (#23) and Washers (#25).
Take the Ball Return Ramp (#20) and attach the Velcro sleeves
around the Top Side Tubes (#8) & (#9). Pull the Velcro under the
Lean Bar (#12) and wrap around Horizontal Bar (#7). (Fig 16)
25 23
25 23
12
6
6
20
89
5
Pull the ramp under the Horizontal Tube
(#7) under the Backboard and attach the
tabs to the Bolts of the Backboard. Connect
the Velcro straps around the Rear Vertical
Tubes, Middle (#5))
14
7
12
Fig 16
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 12/14

Snap the Control Panel (#21) onto the Horizontal Bar (#7) (Fig 17a).
Thread the Control Panel wire through the hole of the laminated
Game Operations “Cheat Sheet” until the Cheat Sheet is next to the Control Panel.
Take the Control Panel wire and weave it through the side netting towards
the back of the backboard. Plug the Control Panel wire into the outlet
labeled “Control Panel” in the Scoring Unit.
Tip: You’ll find complete game directions and operations in this booklet.
The “Cheat Sheet” is intended as a quick handy reference guide
STEP 17
21
7
Fig 17a
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 13/14

TROUBLESHOOTING
If your game isn’t powering on
• Check that the AC Adapter is plugged into the scoreboard. You can also use 4 AA
batteries to power the game.
If your game isn’t counting baskets
• Make sure you have chosen a multi-player game (such as Game 1) on your Control Panel.
• Make sure the sensors are securely plugged into the correct outlets in the
scoreboard (Step 13).
• Make sure the sensors are attached level, with the screws tightened all the way.
If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13).
• Check the connection between the sensors and the scoreboard (Step 13).
Please visit www.pop-a-shot.net/support for more troubleshooting tips and hacks.
SKU# PASPRO19-01
WWW.POP-A-SHOT.NET Pop-A-Shot Pro I Single Page 14/14
POP-A-SHOT PRO | SINGLE GAME OPERATION
Game Options
Starting a game: Press START to start your game.
1. Standard Play
:30 on clock
Announcer and clock count down to start
Baskets are 2 points for 1st :20, then 3 points for final :10 and all bonus time
Bonus: :15 extra at 30 points; :10 extra at 60 points
2. Skeet Shooting
Announcers says “Shoot,” then you have :03 to make a basket
3. Double Or Nothing
:30 on clock. First basket counts for 2 points, then each subsequent basket counts for
double. If no basket is made within :03, next basket is 2 points
4. Overtime
1:00 on clock. Announcer and clock count down to start
Baskets are 2 points for 1st :20, then 3 points for final :10 and all bonus time
Bonus: :15 extra at 30 points; :10 extra at 60 points
5. Sudden Death
:15 on clock
6. Free Play
All baskets count as 2 points