Portwell PQ7-M102XL Series User manual

PQ7-M102XL Series
User's Manual
Version 1.2
Copyright Portwell, Inc., 2010. All rights reserved.
All other brand names are registered trademarks of their respective owners.

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction .................................................................................................................................. 1-1
1.2 Check List ..................................................................................................................................... 1-1
1.3 Product Specification .................................................................................................................. 1-2
1.4 Mechanical Drawing ................................................................................................................... 1-3
1.5 System Architecture .................................................................................................................... 1-4
Chapter 2 Hardware Configuration............................................................................................2-1
2.1 Jumper Setting .............................................................................................................................. 2-1
2.2 Connector Allocation .................................................................................................................. 2-3
Chapter 3 System Installation....................................................................................................3-1
3.1 Intel ATOM processor Z510PT/Z520PT ................................................................................ 3-1
3.2 Intel System Controller Hub US15WPT ................................................................................... 3-1
3.3 Main Memory ............................................................................................................................... 3-2
3.4 Installing the Single Board Computer ....................................................................................... 3-2
3.4.1 Chipset Component Driver .............................................................................................. 3-2
3.4.2 Intel Integrated Graphics GMCH Chip .......................................................................... 3-3
3.4.3 Intel Gigabit Ethernet Controller ..................................................................................... 3-3
3.4.4 Audio Controller ............................................................................................................... 3-3
3.5 Clear CMOS Operation ............................................................................................................... 3-4
3.6 WDT Function .............................................................................................................................. 3-4
3.7 GPIO .............................................................................................................................................. 3-7
Chapter 4 BIOS Setup Information............................................................................................4-1
4.1 Entering Setup .............................................................................................................................. 4-1
4.2 Main Menu ................................................................................................................................... 4-2
4.3 Advanced ...................................................................................................................................... 4-3
4.4 PCIPnP ........................................................................................................................................ 4-17
4.5 Boot .............................................................................................................................................. 4-19
4.6 Security ....................................................................................................................................... 4-23
4.7 Chipset ........................................................................................................................................ 4-24
4.8 Exit ............................................................................................................................................... 4-29
Chapter 5 Troubleshooting........................................................................................................5-1
5.1 Hardware Quick Installation ..................................................................................................... 5-1
5.2 BIOS Setting .................................................................................................................................. 5-2
5.3 FAQ ............................................................................................................................................... 5-4
Appendix A
Appendix B

Preface
How to Use This Manual
The manual describes how to configure your PQ7-M102XL series to meet various
operating requirements. It is divided into five chapters, with each chapter addressing
a basic concept and operation of this Q
SEVEN
Module.
Chapter 1 : System Overview. Presents what you have in the box and give you an
overview of the product specifications and basic system architecture for this model of
single board computer.
Chapter 2 : Hardware Configuration. Describes the definition and location for
Jumpers that you can easily configure your system.
Chapter 3 : System Installation. Describes the CPU, main memory SKU to get a clear
information.
Chapter 4 : IOS Setup Information. Specifies the meaning of each setup
parameters, how to get advanced BIOS performance and update new BIOS. In
addition, POST checkpoint list will give users some guidelines of trouble-shooting.
The content of this manual and EC declaration document is subject to change without
prior notice. These changes will be incorporated in new editions of the document.
Portwell may make supplement or change in the products described in this
document at any time.
Updates to this manual, technical clarification, and answers to frequently asked
questions will be shown on the following web site : http://www.portwell.com.tw

System Overview
PQ7-M102XL Series User Manual 1-1
Chapter 1
System Overview
1.1 Introduction
Q
SEVEN
, a new industrial computer platform in “Module board” and “Carrier board”
architecture, equipped processor or its socket, chipset, memory or memory socket
and single Ethernet controller on it. The On-The-Shelf Module board allows users to
create their own Carrier board easily and quickly since most critical parts are ready
on Module board. Q
SEVEN
Module board offers expansion interfaces such as PCI
Express, SATA, LPC, LVDS, USB, SDVO and Audio etc. that could support variety
functions depending on Carrier board design.
The Carrier board was customized design to fit in different mechanical requirements.
In the meanwhile, its variety functions were also customized to meet the application.
Compares to the platform that designed from nothing, Q
SEVEN
architecture platform
only needs to develop Carrier board. Users could keep their know-how which
related to their core competence in the Carrier board.
PQ7-M102XL series equipped Intel eMenlow chipset with Atom Z510PT/Z520PT
processor on-board), 512 MB DDR2 memories (up to 1GB) on-board, one Gigabit
Ethernet controller on it to provide expansion interfaces – PCI Express x1.
1.2 Check List
The PQ7-M102XL series package should cover the following basic items
One PQ7-M102XL series module board
One Installation Resources CD (Driver and Manual)
If any of these items is damaged or missing, please contact your vendor and keep all
packing materials for future replacement and maintenance.

System Overview
PQ7-M102XL Series User Manual 1-2
1.3 Product Specification
Main processor
- Intel® Atom Processor
- FSB: Z510PT 400MHz; Z520PT 533MHz
Main Memory
Onboard DDR2 400/533 up to 1GB
L2 Cache Memory
512K L2 Cache, Build-in processor
Chipset
Intel eMenlow (US15WPT) chipset
Expansion Interfaces
- PCI Express
 One PCI Express x1 link (One optional link for Ethernet controller)
- LVDS
 Supports maximum 112MHz single channel LVDS interface
 Single channel LVDS interface support: 24 bpp
 Maximum Panel resolution supported up to 1366 x 768
- SDVO (Serial Digital Video Output)
 A maximum pixel clock of 160 MHz is supported on the SDVO interface.
- Ethernet
 Intel WG82574IT Gigabit Ethernet controller is equipped
- USB Interface


 Support eight USB 2.0 ports
Outline Dimension (L X W):
70mm x 70mm
Operating Temperature:
-40°C ~ 85°C
Storage Temperature:
-40°C ~ 85°C
Relative Humidity:
5% ~ 90%, non-condensing

System Overview
PQ7-M102XL Series User Manual 1-3
1.4 Mechanical Drawing

System Overview
PQ7-M102XL Series User Manual 1-4
1.5 System Architecture
PQ7-M102XL Series System lock Diagram
Single Channel DDR2 400/533
Silverthorne XL
(Z510PT/Z520PT)
Poulsbo XL
(U15WPT)
400/533
M
Hz
FSB
18/24bit LVDS
Q
SEVEN
Golden
Finger
Q
SEVEN
Golden Finger
PCI-E x1
(Port 1)
VCC5
5V_SB
BATT
GND
PCI-Ex1
USB x8
HDA
SDVO
IDE
JMB330
SATA Port 0
FWH
BIOS
512MB (up to 1GB)
DDR2 Chips
SATA Port 1
EMC1402
FWH/LPC
SDIO
WG82574IT
MDI
JMB330

Hardware Configuration
PQ7-M102XL Series User Manual 2-1
Chapter 2
Hardware Configuration
This chapter gives the definitions and shows the positions of jumpers, headers and
connector. All of the configuration jumpers on Portwell EVB Carrier PQ7-C100XL are
in the proper position. The default settings shipped from factory are marked ().
2.1 Jumper Setting
Figure 2-1 PQ7-C100XL Jumper & Connector Location
JP1 : LVDS Power Level
JP1 Process Selection
1-3 3.3V 
3-4 12V
3-5 5V

Hardware Configuration
PQ7-M102XL Series User Manual 2-2
JP2 : CPU oard IOS Disable
JP2 Function
1-2 BIOS Disable
JP3 : Auto Power utton selection
JP3 Function
1-2 Auto power button mode
JP4 : RTC CMOS Clear Jumper Setting
JP4 Function
1-3、2-4 For com port 
3-5、4-6 For IrDA
JP5 : US Host/Client Select
JP5 Function
1-2 Host 
2-3 Client
JP6 : COM2 RS232/485/422 Selection
JP6 Function
RS232 5-6,9-11,10-12,15-17,16-18 
RS485 1-2,7-9,8-10,19-20
RS422 3-4,7-9,8-10,13-15,14-16,21-22
JP7 : LVDS ack-light Power Level
JP7 Process Selection
1-3,2-4 5V, Active High 
1-3,4-6 12V, Active High
3-5,2-4 5V, Active Low
3-5,4-6 12V, Active Low
JP8 : CMOS Reset
JP8 Function
1-2 Normal Operation 
2-3 Clear CMOS Contents

Hardware Configuration
PQ7-M102XL Series User Manual 2-3
2.2 Connector Allocation
I/O peripheral devices are connected to the interface connectors.
Connector Function List
Connector
Function Remark
J1 LVDS Panel Back-light Power Connector
J2 RTC Battery Connector
J3/10 SATA Interface Connector
J4 Power Header
J5 LVDS Connector
J6 4P Power Connector for 12V
J7 3P FAN Power Connector (System)
J8 Audio Header
J11 8-Bit GPIO Header
J12 Mini-PCI E Connector
J13 LPC Debug Port
J14 MXM Connector
J15 SD Card Slot
J16 Dual Port USB Header (Only USB2.0 Device)
J17 Client USB Header
J19 Front Panel Control Header
J20 IrDA Connector
J21 RJ45 Lan Port
J22 COM2 Serial Port BOX Header
J23/J24 Dual Port USB
J25 COM 1 Serial Port Connector
J26 D-Sub15 VGA Connector
J27 DC Jack 12V
J28 Reserve Header
Pin Assignments of Connectors
J1 : LVDS Panel ack-light Power Connector
PIN No. Signal Description
1 Backlight Power
2 Ground
3 +12V
4 L_BKLTCTL
5 +5V
J2 : RTC attery Connector
PIN No. Signal Description
1 Positive
2 Negative

Hardware Configuration
PQ7-M102XL Series User Manual 2-4
J3/10 : SATA Interface Connector
PIN No. Signal Description
1 GND GND
2 SATA_TXP0 SATA_TXP1
3 SATA_TXN0 SATA_TXN1
4 GND GND
5 SATA_RXN0 SATA_RXN1
6 SATA_RXP0 SATA_RXP1
7 GND GND
J4 : Power Header
JP2 Function
1 V12
2 GND
3 GND
4 VCC
J5 : LVDS Panel Connector
PIN No.
Signal Description PIN No.
Signal Description
1 VDD_LVDS 2 VDD_LVDS
3 DF_LA_DATA+0 4 DF_LA_DATA-0
5 DF_LA_DATA+1 6 DF_LA_DATA-1
7 DF_LA_DATA+2 8 DF_LA_DATA-2
9 DF_LA_DATA+3 10 DF_LA_DATA-3
11 DF_LA_CLK+ 12 DF_LA_CLK-
13 L_CTLA_CLK 14 L_CTLB_DATA
15 GND 16 GND
17 DF_LB_DATA+0 18 DF_LB_DATA-0
19 DF_LB_DATA+1 20 DF_LB_DATA-1
21 DF_LB_DATA+2 22 DF_LB_DATA-2
23 DF_LB_DATA+3 24 DF_LB_DATA-3
25 DF_LB_CLK+ 26 DF_LB_CLK-
27 N/A 28 N/A
29 GND 30 GND

Hardware Configuration
PQ7-M102XL Series User Manual 2-5
J6 : 4P Power Connector for 12V
1
2
3
4
PIN No. Signal Description
1 Ground
2 Ground
3 +12V
4 +12V
J7 : 3P FAN Power Connector
1
2
3
PIN No. Signal Description
1 Ground
2 +12V
3 Fan Speed Detecting signal
J8 : Audio Header
PIN No. Signal Description
1 CN_MIC-R
2 AGND
3 CN_MIC-L
4 AGND
5 CN_LINOUT-R
6 NC
7 VCC
8
9 CN_LINOUT-L
10 NC
J11 : 8- it GPIO Header
PIN No.
Signal Description PIN No.
Signal Description
1 SIO_GPIO0 2 SIO_GPIO4
3 SIO_GPIO1 4 SIO_GPIO5
5 SIO_GPIO2 6 SIO_GPIO6
7 SIO_GPIO3 8 SIO_GPIO7
9 Ground 10 VCC

Hardware Configuration
PQ7-M102XL Series User Manual 2-6
J12 : Mini-PCIE Slot
PIN No.
Signal Description PIN No.
Signal Description
1 PCIE_WAKE# 2 VCC3
3 N/C 4 GND
5 N/C 6 VCC1_5
7 CLKREQ# 8 N/C
9 GND 10 N/C
11 DF_CLK_PCIE# 12 N/C
13 DF_CLK_PCIE 14 N/C
15 GND 16 N/C
17 N/C 18 GND
19 N/C 20 N/C
21 GND 22 RST#
23 DF_PCIE_RXN1 24 3.3VAUX
25 DF_PCIE_RXP1 26 GND
27 GND 28 VCC1_5
29 GND 30 SMB_CLK
31 DF_PCIE_TXN1 32 SMB_DAT
33 DF_PCIE_TXP1 34 GND
35 GND 36 DF_USB_PN0
37 N/C 38 DF_USB_PP0
39 N/C 40 GND
41 N/C 42 N/C
43 N/C 44 N/C
45 N/C 46 N/C
47 N/C 48 VCC1_5
49 N/C 50 GND
51 N/C 52 VCC3
J13 : LPC Debug Port
PIN No.
Signal Description PIN No.
Signal Description
1 LPC_AD0 2 VCC3
3 LPC_AD1 4 RST#
5 LPC_AD2 6 LPC_FRAME#
7 LPC_AD3 8 CLK_LPC_FWH
9 10 GND
J14 : MXM Connector
PIN No.
Signal Description PIN No.
Signal Description
1 GND 2 GND
3 DF_LAN1_MDIN3 4 DF_LAN1_MDIN2
5 DF_LAN1_MDIP3 6 DF_LAN1_MDIP2
7 LAN1_LINK100- 8 LAN1_LINK1000-

Hardware Configuration
PQ7-M102XL Series User Manual 2-7
9 DF_LAN1_MDIN1 10 DF_LAN1_MDIN0
11 DF_LAN1_MDIP1 12 DF_LAN1_MDIP0
13 LAN1_LINK# 14 LAN1_ACT-
15 VCTREF_GBE0_CT 16 SLP_S5#
17 LPC_PME# 18 SLP_S3#
19 VSB3 20 PWRBTN#_PM
21 SLP_ TN# (not implement) 22 LID_ TN# (not implement)
23 GND 24 GND
25 GND 26 PWROK_Q7
27 ATLOW# (not implement) 28 RST_SYS#
29 DF_SATA0_TX+ 30 DF_SATA1_TX+
31 DF_SATA0_TX- 32 DF_SATA1_TX-
33 SATA_ACT# 34 GND
35 DF_SATA0_RX+ 36 DF_SATA1_RX+
37 DF_SATA0_RX- 38 DF_SATA1_RX-
39 GND 40 GND
41 BIOS_DISABLE# 42 SLOT2_CLK
43 SLOT2_CD# 44 SD2_LED
45 SLOT2_CMD 46 SLOT2_WP
47 SD2PWR# 48 SLOT2_DATA1
49 SLOT2_DATA0 50 SLOT2_DATA3
51 SLOT2_DATA2 52 SLOT2_DATA5
53 SLOT2_DATA4 54 SLOT2_DATA7
55 SLOT2_DATA6 56 RSVD
57 GND 58 GND
59 HAD_SYNC 60 SMB_CLK
61 HAD_RST# 62 SMB_DATA
63 HAD_BITCLK 64 SM _ALERT#
65 HAD_SDATAIN0 66 I2C_CLK
67 HAD_SDATAOUT 68 I2C_DAT
69 PM_THRM# 70 WDTRIG#
71 THERMTRIP# 72 WDOUT (not implement)
73 GND 74 GND
75 DF_USB_PN7 76 DF_USB_PN6
77 DF_USB_PP7 78 DF_USB_PP6
79 USB_6_7_OC# 80 USB_4_5_OC#
81 DF_USB_PN5 82 DF_USB_PN4
83 DF_USB_PP5 84 DF_USB_PP4
85 USB_2_3_OC 86 USB_0_1_OC#
87 DF_USB_PN3 88 DF_USB_PN2
89 DF_USB_PP3 90 DF_USB_PP2
91 US _HOST_PRES# 92 US _HC_SEL
93 DF_USB_PN1 94 DF_USB_PN0
95 DF_USB_PP1 96 DF_USB_PP0
97 GND 98 GND

Hardware Configuration
PQ7-M102XL Series User Manual 2-8
99 LA_DATAP0 100 LB_DATAP0 (not implement)
101 LA_DATAN0 102 LB_DATAN0 (not implement)
103 LA_DATAP1 104 LB_DATAP1 (not implement)
105 LA_DATAN1 106 LB_DATAN1 (not implement)
107 LA_DATAP2 108 LB_DATAP2 (not implement)
109 LA_DATAN2 110 LB_DATAN2 (not implement)
111 L_VDDEN 112 L_BKLTEN
113 LA_DATAP3 114 LB_DATAP3 (not implement)
115 LA_DATAN3 116 LB_DATAN3 (not implement)
117 GND 118 GND
119 DF_LA_CLKP 120 DF_LB_CLKP (not implement)
121 DF_LA_CLKN 122 DF_LB_CLKN (not implement)
123 L_BKLTCTL 124 RSVD
125 LVDS_DID_DAT 126 LVDS_BLC_DAT
127 LVDS_DID_ CLK
128 LVDS_BLC_CLK
129 RSVD
130 RSVD
131 SDVO_CLK+ 132 SDVO_INT+
133 SDVO_CLK- 134 SDVO_INT-
135 GND 136 GND
137 SDVO_GREEN+ 138 SDVO_FLDSTALL+
139 SDVO_GREEN- 140 SDVO_FLDSTALL-
141 GND 142 GND
143 SDVO_BLUE+ 144 SDVO_TVCLKIN+
145 SDVO_BLUE- 146 SDVO_TVCLKIN-
147 GND 148 GND
149 SDVO_RED+ 150 SDVO_CTRLDATA
151 SDVO_RED- 152 SDVO_CTRLCLK
153 N/C 154 N/C
155 DF_CLK_PCIE+ 156 PCIE_WAKE#
157 DF_CLK_PCIE- 158 RST#
159 GND 160 GND
161 PCIE_TX3+ (not implement) 162 PCIE_RX3+(not implement)
163 PCIE_TX3- (not implement) 164 PCIE_RX3- (not implement)
165 GND 166 GND
167 PCIE_TX2+ (not implement) 168 PCIE_RX2+(not implement)
169 PCIE_TX2- (not implement) 170 PCIE_RX2- (not implement)
171 EXCD0_PERST# 172 EXCD1_PERST#
173 PCIE_TX1+ 174 PCIE_RX1+
175 PCIE_TX1- 176 PCIE_RX1-
177 EXCD0_CPPE#
(not implement)
178 EXCD1_CPPE#
(not implement)
179 PCIE_TX0+ 180 PCIE_RX0+
181 PCIE_TX0- 182 PCIE_RX0-
183 GND 184 GND
185 LPC_AD0 186 LPC_AD1
187 LPC_AD2 188 LPC_AD3

Hardware Configuration
PQ7-M102XL Series User Manual 2-9
189 CLK_LPC_FWH 190 LPC_FRAME#
191 LPC_SERIRQ 192 LPC_LDRQ#
(not implement)
193 V3.3A_RTC 194 SPKR
195 FAN_TACHOIN
(not implement)
196 FAN_PWMOUT
(no implement
197 GND 198 GND
199 RSVD
200 RSVD
201 RSVD (use for A20M#)
202 RSVD
203 RSVD
204 MFG_N/C
205 VSB5 206 VSB5
207 MFG_N/C 208 MFG_N/C
209 MFG_N/C 210 MFG_N/C
211 VCC 212 VCC
213 VCC 214 VCC
215 VCC 216 VCC
217 VCC 218 VCC
219 VCC 220 VCC
221 VCC 222 VCC
223 VCC 224 VCC
225 VCC 226 VCC
227 VCC 228 VCC
229 VCC 230 VCC
J15 : SD Card Slo
PIN No. Signal Description
1 DAT3
2 CMD_RSP
3 GND
4 VCC
5 CLK
6 GND
7 DAT0
8 DAT1
9 DAT2
Sa WP#
Sb CD#
Sc CD#_COM
J16 : Dual Port US Header(Only US 2.0 Device)
1
2
7
10
PIN No.
Signal Description PIN No.
Signal Description
1 +5V 2 +5V
3 USBD6N 4 USBD7N
5 USBD6P 6 USBD7P

Hardware Configuration
PQ7-M102XL Series User Manual 2-10
7 Ground 8 Ground
10 NC
J17 : Client US Header
1
2
7
10
PIN No.
Signal Description PIN No.
Signal Description
1 +5V 2 NC
3 USBD1N 4 NC
5 USBD1P 6 NC
7 Ground 8 NC
10 NC
J19 : Front panel Connector
PIN No.
Signal Description PIN No.
Signal Description
1 HD_LED_P 2 FP PWR/SL_P
3 HD_LED_N 4 FP PWR/SL_N
5 RST_SW_N 6 PWR_SW_P
7 RST_SW_P 8 PWR_SW_N
9 RSVD_DNU 10
J20 : IrDA Connector
PIN No. Signal Description
1 IRRX
2 Ground
3 Ground
4 NC
5 IRTX
6 VCC
J21 : RJ45 LAN Port
PIN No. Signal Description
1 L1_MDIP0
2 L1_MDIN0
3 L1_MDIP1
4 L1_MDIN1
5 VCTREF_GBE0_CT
6 GND
7 L1_MDIP2
8 L1_MDIN2
9 L1_MDIP3

Hardware Configuration
PQ7-M102XL Series User Manual 2-11
10 L1_MDIN3
11 LAN1_ACT-
12 LAN1_LINK#
13 LAN1_LINK1000-
14 LAN1_LINK100-
J22 : COM2 Serial Port OX Header
PIN No.
Signal Description PIN No.
Signal Description
1 DCD#2 2 DSR#2
3 RXD#2 4 RTS#2
5 TXD#2 6 CTS#2
7 DTR#2 8 RI#2
9 GND 10
J23 : Dual Port US
PIN No.
Signal Description PIN No.
Signal Description
A1 +5V B1 +5V
A2 USBD3N B2 USBD2N
A3 USBD3P B3 USBD2P
A4 Ground B4 Ground
J24 : Dual Port US
PIN No.
Signal Description PIN No.
Signal Description
A1 +5V B1 +5V
A2 USBD5N B2 USBD4N
A3 USBD5P B3 USBD4P
A4 Ground B4 Ground

Hardware Configuration
PQ7-M102XL Series User Manual 2-12
J25 : COM 1 Serial Port Connector
PIN No.
Signal Description
RS-232 RS-422 RS-485
1 DCD (Data Carrier Detect) TX- DATA-
2 RXD (Receive Data) TX+ DATA+
3 TXD (Transmit Data) RX+ N/C
4 DTR (Data Terminal Ready) RX- N/C
5 GND (Ground) GND GND
6 DSR (Data Set Ready) N/C N/C
7 RTS (Request to Send) N/C N/C
8 CTS (Clear to Send) N/C N/C
9 RI/5V/12V N/C N/C
J26 : D-SU 15 VGA Connector
1
11
15
5
10
6
PIN No.
Signal Description PIN No.
Signal Description
1 RED 2 GREEN
3 BLUE 4 ID0
5 Ground 6 Ground
7 Ground 8 Ground
9 NC 10 Ground
11 ID1 12 DDCDATA
13 HSYNC 14 VSYNC
15 DDCCLK
J27 : DC Jack 12V
PIN No. Signal Description
2 V12CON_IN
3 GND
4 GND

System Installation
PQ7-M102XL Series User Manual 3-1
Chapter 3
System Installation
This chapter provides you with instructions to set up your system. The additional
information is enclosed to help you set up onboard PCI device and handle Watch Dog
Timer (WDT) and operation of GPIO in software programming.
3.1 Intel ATOM processor Z510PT/Z520PT
Configuring System us
PQ7-M102XL will automatically detect the CPU FSB 400/533MHz CMOS used.
CPU speed of Intel ATOM Processor for Mobile can be detected automatically.
3.2 Intel System Controller Hub US15WPT
The Intel® System Controller Hub US15WPT is a low-power chipset in one small
22x22mm package, It combines the Intel® Graphics Media Accelerator
500,memorycontroller, and I/O controller in a single-chip solution while featuring
advanced 3D graphics and extensive I/O capabilities such as USB2.0,SDIO and PCI
Express. It supports Intel® High Definition Audio and hardware video decode
acceleration, a 400/533 MHz CMOS front-side bus, dual independent display.