pottery barn kids GRAYSON User manual

Date: 2016-Jul.-08
Rev: Page 1 of 8
pottery barn kids
GRAYSON STORAGE BED

Date: 2016-Jul.-08
Rev: Page 2 of 8
www.potterybarnkids.com
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Do not remove warning labels. Labels are permanent and not designed to be removed.
Pre-assembly:
Remove allparts and hardware from the box and lay out on a clear carpeted or scratch-free work
surface, as this will avoid damaging partsduring assembly.The shipping box provides an ideal work
surface.
Do not dispose of any packaging or contents of the shipping carton untilassembly is completed to
avoid accidentally discarding small parts or hardware.
Use the parts and hardware lists belowto identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware
and split wood.
Parts Included:
(A) Headboard (1x)
(B) Headboard Left Leg (1x)
(C) Headboard Right Leg (1x)
(D) Footboard (1x)
(E) Side Rail(2x)
(F) Side rail Panel(2x)
(G)Side rail Panel(2x)
(H) Drawers(2x)
(I) Support Rail(2x)
(J) Slats Roll(1 set)

Date: 2016-Jul.-08
Rev: Page 3 of 8
Hardware Included:
Tools required (not included):
Philips Head Screwdriver
(K) Ball TipAllenKey
–1x
(L) Allen Bolt
5/16”x63mm -12 x
(M) Allen Bolt
¼”x63mm –8x
(N) Allen Bolt
1/4”x38mm –20x
(O)Spring Washer 5/16” -
12x
(P)Flat Washer
5/16”-12x
(Q) Spring Washer
1/4”-28x
(R)Flat Washer 1/4”-
28x
(S)Half Moon Washer
5/16”-8x
(T) Half Moon
Washer 1/4”-8x
(X)Phillips head
screw 8x30mm -24x

Date: 2016-Jul.-08
Rev: Page 4 of 8
Assembly Instruction Steps:
1. Attach (B)&(C)to (A) using (K) as shown below.
2. Attach (G&F) to (E) using (K) as shown below. Do not fully tighten .
L
4x
O
4x
P
4x
N
8x
Q
8x
R
8x

Date: 2016-Jul.-08
Rev: Page 5 of 8
3. Attach (E)to (A)&(D) using (K) as shown below. Do not fully tighten.
4. Attach (F&G)to (B&C&D) using (K) ,as shown below. Do not fully
tighten.
L
8x
O
8x
P
8x
S
8x
M
8x
Q
8x
R
8x
T
8x

Date: 2016-Jul.-08
Rev: Page 6 of 8
5.Attach (H)to (F)&(G). making sure the pre-drilled holes align. as shown below.
Do not fully tighten..
6. Adjust the lever(up and down) on (H) . as shown below.
N
4x
Q
4x
R
4x

Date: 2016-Jul.-08
Rev: Page 7 of 8
7. Attach (I)to (H). as shown below. Check alignments andsecureall bolts with (K).
Notes : Make sure the wooden drawer runners, and the rubber stoppers are properly aligned as you
re-install the drawer.
8. Attach Slat Roll (J) to the bed .
N
8x
Q
8x
R
8x
U
24x

Date: 2016-Jul.-08
Rev: Page 8 of 8
9. Assembly is completed.
Care Instructions:
Dust often using a clean, soft, dry, lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish
on our lacquered finish.
If the product is to be stored, store in cool dry place and carefullypackage alloriginal
hardware to protect from loss or damage.
Check fasteners periodically for tightness. DO NOT over tighten, as this may cause
distortion or breakage.
Thank you for your purchase
Stores |catalog | www.potterybarnkids.com
USA 1.800.290.8181