Powell 449H User manual

#3
(A) LEFT SIDE PANEL
(B) RIGHT SIDE PANEL
(C) CROSS BRACES (2)
(D) LARGE DOWELS (12)
(E) FRONT DOOR
(F) BASE
(G) BACK DOOR
(H) CAM-BOLTS (8)
(I) CAM-LOCKS (8)
(J) COVERS (8)
(K) HANDLES (4)
(L) SHORT MACHINE SCREWS (8)
(M) HINGE PINS (4)
IMPORTANT NOTE: Follow instructions listed below in the proper sequence as numbered to assure fast, easy and correct
assembly.
1. Note: Upon opening, thoroughly clean all wood surfaces with furniture polish to remove dust and dirt that may have
settled onto finish during shipment.
2. Insert Small Wood Screws (Y) through ends of Magnets (V) and tighten into underside of Cross Braces (C). Insert Large
Dowels (D) into ends of Cross Braces (C). Insert Large Dowels (D) extending from Cross Braces (C) into corresponding
holes near top edge of Left and Right Side Panels (A,B). Glide on Side Panels (A,B) should face inward. (See ill. #1)
3. Insert Short Machine Screws (L) through holes on back of Front Door (E) and tighten into Handles (K). (See ill. #2)
4. Insert large Wood Screws (Q) through hoops in Basket (N) and tighten into corresponding holes on inside of Front Door
(E). (See ill. #3)
#2
E
K
K
K
L
L
L
L
K
#1
B
C
D
D
D
D
D
D
D
D
A
C
Q
E
Q
Q
N
Made in China
PARTS
ASSEMBLY INSTRUCTIONS (ZH)
MODEL NO. 449H "HEIRLOOM CHERRY"
469H "NOSTALGIC OAK"
ATTENTION: SOME NUMBERED PARTS LISTED ON THE INSTRUCTION SHEET MAY NOT BE IN PARTS BAG AS THEY MAY ALREADY BE ASSEMBLED.
CAREFULLY CHECK PARTS AND PACKING MATERIALS PRIOR TO ORDERING REPLACEMENTS.
Thank you for purchasing this quality product. Be sure to
check all packing material carefully for small parts which
may have come loose inside the carton during shipment.
Separate, identify, and count all parts and metal hardware.
Compare with parts list to be sure all parts are present. If
any part(s) are missing or damaged, phone, fax, or mail
to our Customer Service Department. For efficient and
speedy service, please indicate the model number and
code letter of part(s) needed.
HARDWARE ILLUSTRATION
Tools required: Screwdriver (not included)
(N) BASKET
(O) TRAY
(P) TOP
(Q) LARGE WOOD SCREWS (4)
(R) DECORATIVE CROSS BRACES (3)
(S) LEFT MAGAZINE RACK PANEL
(T) RIGHT MAGAZINE RACK PANEL
(U) KNOBS (3)
(V) MAGNETS (2)
(W) LONG MACHINE SCREWS (6)
(X) SMALL DOWELS (12)
(Y) SMALL WOOD SCREWS (4)
X D W L Y Q U H M I J V

#5
X
X
F
S
X
W
W
W
W
X
X
X
R
T
R
A
P
G
M
HH
O
#4
M
A
D
F
D
M
H
V
I
J
C
H
J
I
E
M
5. Tighten Cam-bolts (H) into threaded holes in Base (F). Insert Large
Dowels (D) into center holes in Base (F). Insert Cam-locks (I) into
large holes near bottom edge of Side Panels (A,B). Rotate Cam-
locks (I) with a screwdriver so arrow points toward Cam-bolts (H).
Note: Be sure that slot for screwdriver faces outward. Insert long
end of Hinge Pins (M) into top and bottom corners of Doors (E,G).
Align holes on bottom edge of Side Panels (A,B) with Cam-bolts
(H) and Large Dowels (D) extending from Base (F) and insert Cam-
bolts (H) and Large Dowels (D) into holes in bottom edge of Side
Panels (A,B). Insert Hinge Pins (M) extending from bottom corner of
Doors (E,G) into hole in Base (F). Lift Side Panels (A,B) slightly to
allow insertion of Hinge Pins (M) extending from top corner of
Doors (E,G) into hole in Cross Braces (C) and push Side Panels
(A,B) and Cross Braces (C) downward until Side Panels (A,B) rests
on Base (F). Rotate Cam-locks (I) clockwise to secure Side Panels
(A,B) to Base (F). Push Covers (J) into Cam-locks (I). (See ill. #4)
6. Tighten Cam-bolts (H) into threaded holes in Top (P). Insert Cam-
locks (I) into large holes near top edge of Side Panels (A,B). Rotate
Cam-locks (I) with a screwdriver so arrow points toward Cam-bolts
(H). (See ill. #4)
7. Rest Tray (O) onto Cross Braces (C) and glides attached to Side
Panels (A,B). Finished side of Tray (O) should face upward. Tighten
Knobs (U) into ends of Tray (O). Tighten Cam-bolts (H) into
threaded holes and insert Large Dowels (D) into center holes in
Top (P). Align Cam-bolts (H) and Large Dowels (D) extending from
Top (P) with holes in top edge of Side Panels (A,B) and Press down
on Top (P) until Top (P) rests on Side Panels (A,B). Rotate Cam-
locks (I) clockwise to secure Top (P) to Side Panels (A,B). Push
Covers (J) into Cam-locks (I). (See ill. #4)
8. Insert Small Dowels (X) into ends of Decorative Cross Braces
(R). Insert Small Dowels (X) extending from Decorative Cross
Braces (R) into corresponding holes of Left and Right
Magazine Rack Panels (S,T). Insert Long Machine Screws (W)
through inside of Left Side Panel (A), and tighten into holes
on edge of Left and Right Magazine Rack Panels (S,T). Insert
Long Machine Screws (W) through bottom of Base (F), and
tighten into holes on end of Left and Right Magazine Rack
Panels (S,T). (See ill. #5)
9. Your furniture has been handcrafted and skillfully finished by
fine craftsmen. Rich, deep antique finishes have been
applied which require very little polish. However, should you
desire a shinier finish, simply use any good grade of furniture
polish, rubbing the finish lightly as it is being applied. Allow to
dry and buff lightly with a soft cloth.
U
U
H
U
HC
MODEL NO. 449H "HEIRLOOM CHERRY"
469H "NOSTALGIC OAK"
Made in China
Place of Purchase
Daytime Phone ( )
Address
Name
Reason for Replacement
Part Letter Description Quantity
FAX this form to ( 10) 841-0842
or call Customer Service at [phone] or [phone]
Have your model number and part code letter handy.
IF YOU HAVE A PROBLEM, WE WANT TO HAVE THE OPPORTUNITY TO MAKE IT RIGHT!
Should there be any missing or defective part(s),
Rev. 06/02/03
Powell Service Department • P.O. Box 1408, Culver City, CA 90232-1408
© 1997 Powell