Power Arc 12-2 VN User manual

(-) Negative
Battery or Frame
2 Cylinder, 1 Plug/Cylinder
(12 Volt Negative Ground)
Wasted Spark
Static
Timing LED
To +12 VDC from
Kill Switch or
Switched Power
Gray:
To Points
White - Coil TRIG
Black - GND
MC-2
Coil
Stop
Before wiring
disconnect the
battery !!
Smart
Points
Module
12-2 VN
Red
Points
(-) Negative
Battery or Frame
Static
Timing LED
To +12 VDC from
Kill Switch or
Switched Power
Gray:
To Points
White - Coil TRIG
Black - GND
Smart
Points
Module
12-2 VN
Red
Points
Stop
Before wiring
disconnect the
battery !!
(12 Volt Negative Ground)
Distributor or Single cylinder
MC-1
WARNING: Do not touch output wire (White) To +12.
DO NOT use Solid or Spiral wound suppression spark plug
wires of less than 800° per foot. Failure to observe these
precautions will damage Ignition & Void the Warranty.
1. Disconnect the battery Positive (+) wire.
2. Turn the ignition/kill switch OFF. Remove and replace the
existing ignition coil with a Power Arc Coil MC-1/2 Coil.
3. Attach the black smart points module wire to the - (NEG)
terminal of the coil and a wire from coil - (NEG) terminal to the
negative battery (-) or frame.
4. Attach the red power wire of the smart points module to the
ignition/kill switched power.
5. Remove the condenser from the distributor or points housing
and attach the gray wire to the points. Condenser may be left in
place if you disconnect the wire and isolate. If you have 2 sets
of points hook them together and attach to the gray wire and
isolate the condenser wires.
6. DO NOT attach the white wire to the TRIG of the MC-1/2 coil.
7. Connect the battery Positive (+) wire.
8. Reduce dwell (widen gap) by 25% and set your points timing
as per your applications instructions. The coil will not fire as
long as gray wire is not hooked to the TRIG terminal of the coil.
9. Power on ignition/kill switch and using the Red static timing
LED (lights when points are closed)
10. Power the ignition/kill switch OFF
11. Hook the white wire to the coil TRIG terminal.
12. Install spark plug wires as per appropriate coil used and
install on spark plugs. Wires may go to either spark plug.
13. Power the ignition/kill switch ON.
14. Start the Engine.
POWER ARC IGNITIONS CO., INC.
2518 N. E. 102 AVE.
ANKENY, IA 50021
[phone]
http://www.powerarc.com
PATENT #4,951,629 OTHER PATENTS PENDING
OWNERS MANUAL
All information contained in this owner manual is the property of P. A. Ignition Co., Inc. and
cannot be duplicated in whole or in part by any means or disseminated or distributed
without the prior written consent of P. A. Ignitions Co., Inc. The information in this manual
has been carefully compiled and checked for accuracy and is believed to be correct.
However, P. A. Ignition Co., accepts no responsibility for inaccuracies which may occur. All
specifications in this manual are subject to change without notice.
The following customer actions automatically voids the warranty.
1) Use of any other spark plug wires other than resistor type wires with at least 800 ohms
of resistance. 2) Use of non-resistor spark plugs. 3) Drilling or cutting of any kind into the
module 4) Incorrect wiring of the module. 5) Use of module on systems with defective
charging systems. 6) Use of defective coils. 7) Directly shorting the coil output wires to +12
VDC. 8) Physical damage to the ignition . 9) Any other items covered in the warranty &
instruction manual.
LIMITED WARRANTY
P. A. Ignition Co., Inc. warrants to the original retail purchaser of a Smart Points ignition that it
will, free of charge, repair or replace at its own option, the product if returned to P. A. Ignition
Co., Inc. within 6 months from date of purchase and if found by P. A. Ignition Co., Inc. to be
defective in material or workmanship. This warranty is not transferable by the purchaser and
shall be voided: if alterations not authorized by P.A. Ignition Co., Inc. are made in the equipment
or if the serial number or date of manufacture has been altered, defaced or removed. Nor does
this warranty apply: if the equipment has been subjected to accident, misuse, improper
hookup, damaged by flood, fire, or act of God, or has been used on circuits or voltages other
than those indicated in its instruction manual. If the equipment is found to be defective in
materials or workmanship the equipment will be returned and P. A. Ignition Co., Inc. will pay the
return shipping (this does not include next day shipping, second day shipping, shipments
outside of the continental U. S. A. or shipments outside of the U.S.A.). All warranty work
outside of the U.S.A. must include prepayment of return shipping. Customs, duties or tariffs
are not covered by this warranty. If the equipment is found to be defective but is due to
customer misuse (as described in warranty) P. A. Ignition Co., Inc. will notify the customer and if
the customer wants the defective equipment returned P. A. Ignition Co., Inc. will return the
equipment C.O.D. freight. If the equipment is found to be in operational order when returned to
the factory P. A. Ignition Co., Inc. will return the module with a $35.00 service charge plus freight
and C.O.D. Charges.
Any module returned under the warranty must include note of explanation of failure and
be accompanied by a dated bill of sale.
P. A. Ignition Co., Inc. warranty obligations are limited to those set forth herein and no other
obligations, expressed or implied, are assumed by P.A. Ignitions Co., Inc.
Some states do not allow the exclusions or limitations of incidental or consequential
damages, or allow limitations on how long an implied warranty lasts, so the above
limitations or exclusions may no apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
The Smart Points low current input reduces wear and extends
the life of ignition points eliminating pitting or arcing at the
points.
Automatic coil shutoff prevents damage to coil, points or
electronic trigger units when the ignition key or switch is left on
accidentally.
Exceptional low voltage operation of the Smart Points and coil
means improved starting.
Static timing indicator for easier more accurate installation and
points setup.
Smart Points
12-2 VN
2 Cylinder, 1 Plug/Cylinder
(12 Volt Negatvie Ground)
Wasted Spark

DCR
Wire
Must be inserted between the distributor
and the Smart Points coil.
(-) Negative
Battery or Frame
Static
Timing LED
To +12 VDC from
Kill Switch or
Switched Power
Gray:
To Points
White - Coil TRIG
Black - GND
Smart
Points
Module
12-2 VN
Red
Points
Stop
Before wiring
disconnect the
battery !!
POWER ARC IGNITIONS CO., INC.
2518 N. E. 102 AVE.
ANKENY, IA 50021
[phone]
http://www.powerarc.com
PATENT #4,951,629 OTHER PATENTS PENDING
1. Disconnect the battery Positive (+) wire.
. Remove and replace the existing
ignition coil with Power Arc oil .
3. Attach the black module wire to the - (NEG) terminal
of the coil and a wire from coil - (NEG) terminal to the negative
battery (-) or frame.
4. Attach the red wire to the
5. Remove the condenser from the distributor or points housing and
attach the gray wire to the points. Condenser may be left in place if
you disconnect the wire and isolate. If you have 2 sets of points
hook them together and attach to the gray wire and isolate the
condenser wires.
6. DO NOT attach the white wire to the TRIG of the MC-1 coil.
.
10. Power the
11. Hook the white wire to the coil TRIG terminal.
Install spark plug wire on spark plugs.
1 . Power the
14. Start the Engine.
2 Turn the ignition/kill switch OFF.
a C MC-1 Coil
smart points
power of the smart points module
ignition/kill switched power.
ignition/kill switch and
ignition/kill switch OFF
12. If used on distributor
ignition DCR Wire must be
3 ignition/kill switch ON.
7. Connect the battery Positive (+) wire.
8 Reduce dwell (widen gap) by 25% and set your points timing as
per your applications instructions. The coil will not fire as long as
gray wire is not hooked to the TRIG terminal of the coil.
9. Power on using the Red static timing LED
(lights when points are closed)
inserted between the distributor
and the Smart Points coil.
(12 Volt Negative Ground)
Distributor or Single cylinder
MC-1
OWNERS MANUAL
All information contained in this owner manual is the property of P. A. Ignition Co., Inc. and
cannot be duplicated in whole or in part by any means or disseminated or distributed
without the prior written consent of P. A. Ignitions Co., Inc. The information in this manual
has been carefully compiled and checked for accuracy and is believed to be correct.
However, P. A. Ignition Co., accepts no responsibility for inaccuracies which may occur. All
specifications in this manual are subject to change without notice.
The following customer actions automatically voids the warranty.
1) Use of any other spark plug wires other than resistor type wires with at least 800 ohms
of resistance. 2) Use of non-resistor spark plugs. 3) Drilling or cutting of any kind into the
module 4) Incorrect wiring of the module. 5) Use of module on systems with defective
charging systems. 6) Use of defective coils. 7) Directly shorting the coil output wires to +12
VDC. 8) Physical damage to the ignition . 9) Any other items covered in the warranty &
instruction manual.
LIMITED WARRANTY
P. A. Ignition Co., Inc. warrants to the original retail purchaser of a Smart Points ignition that it
will, free of charge, repair or replace at its own option, the product if returned to P. A. Ignition
Co., Inc. within 6 months from date of purchase and if found by P. A. Ignition Co., Inc. to be
defective in material or workmanship. This warranty is not transferable by the purchaser and
shall be voided: if alterations not authorized by P.A. Ignition Co., Inc. are made in the equipment
or if the serial number or date of manufacture has been altered, defaced or removed. Nor does
this warranty apply: if the equipment has been subjected to accident, misuse, improper
hookup, damaged by flood, fire, or act of God, or has been used on circuits or voltages other
than those indicated in its instruction manual. If the equipment is found to be defective in
materials or workmanship the equipment will be returned and P. A. Ignition Co., Inc. will pay the
return shipping (this does not include next day shipping, second day shipping, shipments
outside of the continental U. S. A. or shipments outside of the U.S.A.). All warranty work
outside of the U.S.A. must include prepayment of return shipping. Customs, duties or tariffs
are not covered by this warranty. If the equipment is found to be defective but is due to
customer misuse (as described in warranty) P. A. Ignition Co., Inc. will notify the customer and if
the customer wants the defective equipment returned P. A. Ignition Co., Inc. will return the
equipment C.O.D. freight. If the equipment is found to be in operational order when returned to
the factory P. A. Ignition Co., Inc. will return the module with a $35.00 service charge plus freight
and C.O.D. Charges.
Any module returned under the warranty must include note of explanation of failure and
be accompanied by a dated bill of sale.
P. A. Ignition Co., Inc. warranty obligations are limited to those set forth herein and no other
obligations, expressed or implied, are assumed by P.A. Ignitions Co., Inc.
Some states do not allow the exclusions or limitations of incidental or consequential
damages, or allow limitations on how long an implied warranty lasts, so the above
limitations or exclusions may no apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
The Smart Points low current input reduces wear and extends
the life of ignition points eliminating pitting or arcing at the
points.
Automatic coil shutoff prevents damage to coil, points or
electronic trigger units when the ignition key or switch is left on
accidentally.
Exceptional low voltage operation of the Smart Points and coil
means improved starting.
Static timing indicator for easier more accurate installation and
points setup.
Smart Points
12 VN
Distributor or Single cylinder
(12 Volt Negative Ground)
WARNING: Do not touch output wire (White) To +12.
DO NOT use Solid or Spiral wound suppression spark plug
wires of less than 800° per foot. Failure to observe these
precautions will damage Ignition & Void the Warranty.