POWER START PS750LI Assembly instructions

1
PS750LI
Operating & Safety Instructions
GENERAL
The 12V Jump Starter PS750Li is designed to assist with starting 12 Volt vehicles that have
discharged batteries. To ensure safe and trouble-free operation of your PS750LI you must follow the
instructions below.
IMPORTANT INFORMATION FOR YOUR SAFETY
DO NOT SHORT CIRCUIT OR TAMPER WITH THIS UNIT. ALWAYS OBSERVE
CORRECT POLARITY AND SYSTEM VOLTAGE WHEN CONNECTING.
Failure to do so may lead to a HAZARDOUS situation, Damage the pack or the vehicle and may
invalidate the warranty.
Remove personal items such as rings, bracelets and watches when working with a vehicle
battery.
Use PS750Li for boosting standard 12 Volt vehicle batteries only.
Switch unit off when not in use.
WARNING
Before initial use, the PS750Li must be put on charge overnight (16Hrs). Failure to do so
may reduce the life of the product and invalidate the warranty.
CHARGING
CHECKING STATE OF CHARGE
The state of charge is best checked 2 hours after charging. Ensure all cables are disconnected. Push
the “Push to test” button. The LEDs will indicate the approximate state of charge of the unit.

2
WARNING: The PS750LI MUST BE SWITCHED OFF and the switch key must be
removed BEFORE the charger is connected to it. Ensure all output cables are
disconnected. Failure to do so may damage the charger and will prevent the unit from charging.
Connect the supplied charger to the “CHARGE SOCKET” on the front of the unit. Plug the
charger into the mains (230 VAC 50 Hz). Switch on the charger using the switch on the side
of the charger case. The “CHARGE INDICATOR” LED will illuminate on the unit. The LEDs on
the charger will indicate when the unit is ready for use, however, the PS750LI must be left on
charge when it is not being used. The charger supplied is designed for this purpose.
Before disconnecting the charger from the PS750LI, switch off the charger using the switch
on its side. Only charge using the supplied charger. No other charger should be used as
this may cause damage to the battery. Never leave the PS750LI discharged at any
time. This may cause permanent damage to the batteries and will invalidate the warranty
CHARGING FROM A VEHICLE
The PS750LI may also be charged from a 12 Volt vehicle cigarette lighter socket by using the cigarette
lighter lead supplied. This lead is designed to connect to the charge socket on the PS750LI to the
cigarette lighter on the vehicle. The PS750LI will only be recharged slowly using this lead and only while
the vehicle engine is running. Therefore the pack should normally be recharged using the mains
charger. Insufficient charging of the pack may result in failure and this is not covered by
the Warranty.
STARTING & CONNECTIONS
STARTING VEHICLES
Always follow the vehicle manufacturer’s instructions for safe jump-starting. Ensure the PS750Li key-
switch is in the "OFF" position (all LED’s are off). Switch off all lights and other loads on the vehicle.
Connect the positive (RED) clamp to the vehicle system observing correct polarity. Next connect the
negative (BLACK) clamp.
If the connection polarity is wrong then a buzzer will sound. Disconnect the clamps and reconnect
correctly. Always check that the connection polarity is right even if the buzzer does not sound.
Switch on PS750Li by inserting and turning the switch key to the ON position. Make sure cables are
free of turning parts of engine and start the engine normally. If the engine does not start within 10
seconds, stop and wait for one minute before making a further attempt.
After the engine has started, allow it to run for a few minutes to recharge the vehicle’s on-board battery.
Switch off the engine then switch off the PS750Li. First remove the negative clamp, then the positive
clamp. Store the clamps in the end compartment of the PS750Li. Restart the engine from the vehicle’s
on-board battery.
Note: It is not recommended that the PS750Li is used to start vehicles without a battery fitted or with
a battery that has had the electrolyte dried out. Damage may occur to the PS750Li or the vehicle if the
PS750Li is disconnected or switched off while the engine is running.
TO USE AS AN AUXILLIARY POWER SOURCE
The PS750Li can also be used to maintain the vehicle’s computer memory functions when the vehicle’s
on-board battery is disconnected. The optional lead with two cigarette lighter plugs is used for this
purpose but can only be used with 12 V vehicle systems. The cigarette lighter socket on the PS750Li
cannot be used for charging the batteries.
MAINTENANCE

3
The unit case must not be opened as there are no user serviceable parts inside and this will invalidate
the Warranty.
VOLTAGE “SPIKE” PROTECTION
The PS750LI has a spike protection system. This protection is in operation as long as the clamps are
connected to the vehicle, even when the unit key-switch is switched off. NEVER remove one of the
clamps before the key-switch is switched off.
DISPOSAL
The batteries inside the PS750Li are sealed lead types. They must be removed and recycled or disposed
of properly at the end of their useful life.
PS750LI LAYOUT
1
12V OUTPUT LEAD
2
CHARGER SOCKET
3
PUSH TO TEST BUTTON
4
STATE OF CHARGE LEDS
5
MAIN SWITCH
6
CIGARETTE LIGHTER SOCKET
PS750LI Technical Specifications
6
1
2
3
4
5

4
PS750LI
Power Source
12V, 8Ah
Cranking Amps
750A
Peak Amps
1200A
Main Switch
Heavy Duty
Polarity Alarm
Acoustic
Cable Size
25mm²
Clamps
Fully insulated
Heavy Duty
Housing
High Density Polyethylene
H x W x D mm
315 x 365 x 120
Weight (approx)
4.75kg
Mains Charger
230V AC
14.8V DC
2 Amps
We reserve the right to change the specification without notice