PowerNet S023 User manual

INSTRUCTIONS
S023 | 18.5 X 6.5 SOCCER GOAL
WWW.POWERNETINC.NETPOWERNET,INC@POWERNET_BASEBALLPOWERNETBASEBALLNET
13959 CENTRAL AVENUE•CHINO•CA•91710 • 909.203.5495
Out Work! Out Play!
PowerNet Inc. is dedicated to providing quality products at affordable prices. Our goal is to develop the skills
of the young, old, seasoned and professional athletes through training, reps and practice. Further building
confidence leading to consistent winning performance.
Using PowerNet’s equipment indoors and outdoors creates better players. PowerNet gives the opportunity
to have the accessibility to practice anywhere with our nets and equipment. We believe that using the
process of integrating practice in your daily lives allows you to mold the next generation into professionals &
professionals into icons through their performance. Separating the best players from the good by providing
life skills for the future.
Thank you for choosing Powernet
Our Vision
OTHER SOCCER SIZES:
12X6
FUTSAL 3X2M6X4 8X4
14X7 24x8 NOT SHOWN

5a. Then place the
black loop around
the front base post
holder.
EASY SETUP & EASY TEARDOWN
INSTRUCTIONS
2. Open up middle hinge bracket of the
base frame until it locks on both sides.
S023 I (18.5 X 6.5) SOCCER GOAL
SOCCER
CHECK OUT OUR VIDEO INSTRUCTIONS AT:
WWW.POWERNETINC.NETPOWERNET,INC
1. 3.
2.
4.
WARNING:
• Use adult supervision and follow
instructions when using and
setting up the net.
• Frequent use and/or abuse will
eventually strain the net and will
cause breakage.
• Keep fingers away from hinges
and joints.
• This is not a toy, do not climb or
swing on net.
• Don’t drag the net! Use two
people to move.
Out Work! Out Play!
4a. Insert one of the
lower metal poles into
the back of the frame.
5.
TIP: Best used when weighing down net
with PowerNet sandbags (not supplied).
6a. Standing by the front of the net,
on one side, slide sleeve up and hook
the white loop on the net around the
silver notch.
6.
7a. Stand on the outside of the frame by the
back poles.
7.
UPPER POLES
NOTE: Step 1c will extend the back base to
make it a rectangle. If you do NOT extend
the back base it will look like this:
IMPORTANT NOTE:
Near the middle hinge bracket, there are two designed bends
used to raise the frame off the ground for stability.
These are NOT damages!
NOTE: The back side of
the frame is where the
hinges meet and there
is no red sleeve.
NOTE: All four hinges should be locked into place from
steps 2 and 3.
6b. Then repeat 6a on the opposite
side with the second white front loop.
7b. While firmly holding the back pole and
net, hook the white loop on the net around
the sliver notch.
7c. Then repeat steps 7a & 7b on the opposite
side with the second white back loop.
PULL UP
1c. Slowly telescope the legs up on
one side of the frame until it locks.
1b. Then set one leg down
on the ground.
1d. Repeat steps 1b-1c on opposite side.
4b. Then insert the upper
fiberglass pole into the
lower metal pole.
4c. Repeat steps 4a-4b
on opposite side’s back
pole.
5c. Slip one net sleeve
over one fiberglass
pole set. 5e. Repeat 5a-5d on
opposite side.
PARTS LIST
(1) NET
(1) BASE FRAME
(4) LOWER METAL POLE
(4) UPPER POLES
(4) GROUND STAKES
(1) BAG
NOTE: Don’t pull post
all the way out of frame.
1a. Unwrap the net and
place the double hinge on
the ground.
3b. Repeat 3a
on the opposite
side of the base
frame.
3a. Lift side leg
of the frame
until the hinge
locks.
NOTE: Per step 1 the center is designed
to be raised & curved off the ground.
Don’t force the middle down!
LOAD
WARNING: In steps 6 & 7 don’t stand in direction of the pole’s load when bending.
The pole may snap back and cause injury.
LOAD
5d. Next insert it into
the holder on either
side of the front base.
5b. Connect an upper
fiberglass pole into a
lower metal pole.
3c. Place both
legs on ground
with post inserts
up.