Powersmart DB6701 User manual

16 IN. REEL MOWER
Français p. XXEspañol p. 12
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-791-9458.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
1
MODEL #DB6701

TABLE OF CONTENTS
2
Safety Information .........................................................................................3
...................................................................................................................
............................. 4
Care And Maintenance ........................................................................................................................................9
Assembly Instructions.........................................................................................................................................6
Operating Instructions ........................................................................................................................................8
Warranty ..............................................................................................................................................................10
Replacement Parts List ...................................................................................................................................11
Package Contents
.......................................................
........................................................................................................... ............................. 2
Product Specifications
PRODUCT SPECIFICATIONS
PRODUCT SPECIFICATIONS
Cutting path 16 in.
Blade type 5 helical blades
Height adjustments 4 heights: 5/6 in. - 1-4/5 in.
Functions Cutting
Weight 23 lbs.
Hardware Contents ..............................................................................................................................................5

3
SAFETY INFORMATION
CAUTION
Please read and understand this entire manual before attempting to assemble, operate or install the product. If
you have any questions regarding the product, please call customer service at 1-800-791-9458.
READ YOUR OPERATOR’S MANUAL COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET
UP OR OPERATE YOUR NEW REEL MOWER. ALL OPERATORS OF THIS EQUIPMENT SHOULD READ
AND UNDERSTAND ALL SAFETY RULES PRINTED ON THE MACHINE AND IN THIS OPERATOR’S
MANUAL BEFORE USE.
Never place hands, fingers or feet inside the reel. Although a motor does not power this mower, when the
wheels turn the reel spins and can cut.
Never mow when grass is wet as it can be slippery.
Do not use the reel mower while barefoot or while wearing sandals.
Walk behind, never run, while using reel mower. Always make sure of your footing when using this reel mower.
Never intentionally strike or hit trees, fences, etc. This can cause injuries or severely damage the reel mower
mechanisms.
Make sure your reel mower is in a safe operating condition. Do not attempt to operate this reel mower if dam-
aged. Contact customer service or have the reel mower repaired by a qualified repair service provider before
using.

4
YTITNAUQNOITPIRCSEDTRAP
A
Top handle
1
B
Center handle pieces
1
C
Lower handle
Reel mower body
2
D 1
E
Foam grip
1
B
A
D
E
C
PACKAGE CONTENTS

5
HARDWARE CONTENTS
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
PREPARATION
AA
M6 x 35
Carriage Bolt
Qty. 6
BB
DIA. 6
Washer
Qty. 6
CC
M6
Fixing Knob
Qty. 6
Estimated Assembly Time: Less than 15 minutes.

6
ASSEMBLY INSTRUCTIONS
ASSEMBLING THE HANDLE
1. Insert the two center handle pieces (C) into the left and
right side of the top handle (B) and secure with two
carriage bolts (AA), washers (BB), and fixing knobs (CC).
NOTE: The carriage bolts should be inserted from the
downside of the handle so that the washers and the
fixing knobs are inserted upside of the handle.
1
CC
BB
AA
B
A
C
2
CC
BB
BB
CC
AA
D
2. Attach the top handle subassembly to the lower handle
(D) using four carriage bolts (AA), washers (BB), and
fixing knobs (CC).
NOTE:
The carriage bolts should be inserted from the
inside of the handle so that the washers and the
fixing knobs are inserted outside of the handle.

7
ASSEMBLY INSTRUCTIONS
ATTACHING THE HANDLE TO THE MOWER BASE
3. Align the holes at the bottom of the arms of the lower
handle (D) with the posts extending from the side plates
on the reel mower body (E). Slide lower ends of handle
arms onto posts.
3
D E
CUTTING HEIGHT ADJUSTMENTS
1. The cutting height of the mower can be adjusted from
5/6 – 1-4/5 in. with 4 positions for
adjustment height, using the roller assembly.
2. For the highest cutting level, move the adjustment
knobs to position A as shown in Fig. 4.
3. For the lowest cutting level, move the adjustment
knobs to position B as shown in Fig. 4.
4. Other cutting heights are achieved by moving the
adjustment knobs to any stop between the highest
and lowest positions.
4
position A
position B
The highest
cutting position
The lowest
cutting position
The height
adjustment knob
NOTE: The maximum grass cutting height for most grass types
is 3 in. If the grass exceeds 3 in., the following guidelines are
recommended; however, results will vary depending on lawn
type and condition.
Increase cutting height for initial cutting, then lower as needed
during repeat cutting.
Overlap cutting paths.
Mow the same path in opposite directions.

8
OPERATING INSTRUCTIONS
MOWER BLADE ADJUSTMENT
NOTE: Blades are factory adjusted.
Misalignment can occur, often caused by blades
being too loose or too tight. This can cause an
uneven cut or difficulty pushing the mower.
Each end of the cutting bar is adjusted separately.
To move the cutting bar closer to the blades, turn the
adjustment screw clockwise. To move the cutting bar
away from the blades, turn the adjustment screw
counterclockwise.
Adjustment
screw
WARNING
BLADES ARE EXTREMELY SHARP. TO AVOID INJURY, DO NOT TOUCH BLADES WHEN
MAKING ADJUSTMENTS.
CAUTION
djusting the screws for blade adjustments is a very sensitive procedure. A sixteenth of a turn is considered a
major adjustment. efore tightening one adjustment screw, make sure to loosen the opposite screw an equal
amount.
1. Turn mower upside down.
2. Insert a piece of paper between cutter bar and reel blades and slowly turn wheel by hand.
3. All blades should slice the paper evenly along the entire length of the cutter bar while the reel turns smoothly.
4. If mower has an intermittent cut, adjustment should be made to the appropriate side of blades to attain proper
cutting action.
WARNING
Do not overtighten adjustment screws, as this could damage cutter bar. Both screws must be tight
on final adjustment.

9
CARE AND MAINTENANCE
1. Minimum care is required to ensure smooth operation of your mower.
2. To avoid damage to mower or cutting blades, keep area to be mowed free from debris.
3. For best results, regularly apply lubricant to mower s cutting surfaces, cutting reel axle shaft and wheels.
NOTE: Clean any grinding compound or debris from the cutter bar blade, reel blade, pinions, and pawls.
Cleaning and Storage:
3. Store the mower in a dry place. Do not place other objects on top of the mower during storage.
3. Turn the reel blades until the front edge of the cutter bar blade is polished.
Sharpening the cutting blades:
1. Spread a thin layer of lapping compound on the front edge of the reel blades.
2. Adjust the cutter bar so that the blade has light but firm contact across the full width of the cutter bar.
NOTE: Use industrial or valve lapping compound between 100 and 240 grit. Lubricate the axle and pinion with a
light film of wheel bearing grease.
1. Clean the exterior of the machine thoroughly using a soft brush and cloth before storing. Do not use water,
solvents or polishes.
2. Turn the mower on its side to clean the blade area.
Clean any grinding compound or debris from the cutter bar blade, reel blade, pinions and pawls.
WARNING
Do not place hands in the mower near blades. If grass cuttings are compacted in the blade area,
remove using a wood or plastic cleaning tool appropriate for the cleaning of the blades.
WARNING
Do not overtighten the adjusting screws, as this could damage the cutter bar. Tighten both screws during final
adjustment.
CAUTION
· Reel mowers are not effective for rough terrain, excessively bumpy or overgrown yards. If the wheels do not
have traction and cannot turn at a steady fast rotation, the blade will not turn fast enough to cut the grass. In
addition, the reel mower can only cut the blades of grass that are between the reel and the cutter bar.
Uneven terrain makes it increasingly difficult for cutting.
· Reel mowers may not typically cut wood stems, branches, or tall thick grass types such as Zoysia, St
Augustine
and Bermuda. In addition, they have difficulty cutting tall weeds such as dandelions and buckthorn. The reel
mower may tend to push them over and not actually cut them.
· Reel mowers do not cut close to the edge of the mower. The wheels of a reel mower are outside of the blades.

10
WARRANTY
The manufacturer warrants to the original purchaser that each new product and service part is free from defects
in material and workmanship and agrees to repair or replace under this warranty any defective product or part as
follows from the original date of purchase.
1 Year Limited Warranty
THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER:
Products sold damaged or incomplete, sold "as is," sold reconditioned or used as rental equipment.
Delivery, installation or normal adjustments explained in
Damage or liability caused by shipping, improper handling, improper installation, incorrect voltage or improper
wiring, improper maintenance, improper modification, or the use of accessories and /or attachments not
specifically recommended.
Repairs necessary because of operator abuse or negligence, or the failure to install, operate, maintain and store
manual.
Damage caused by cold, heat, rain, excessive humidity, corrosive environments and materials, or other
contaminants.
Expendable items that become worn during normal use.
Cosmetic defects that do not interfere with tool functionality.
Freight costs from customer to vendor.
ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT
FROM ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT.
Some states do not allow the exclusion or limitations on how long an implied warranty lasts, so the above
limitations may not apply to you.
WARRANTY REPLACEMENT PARTS are available b
y
calling the toll-free number,1-800-791-9458.