Powersmart DB5021LED User manual

INSTRUCTION MANUAL
EN 21"ELECTRIC SNOW THROWER
FR 21"CHASSE-NEIGE ÉLECTRIQUE
ES LANZDE NIEVE ELECTRICA DE 21"
Model
Have product questions or need technical support? Please feel free to contact us!
Website: www.PowerSmartUSA.com
Tollfree:1-800-791-9458Mon-Fri9-5EST
Email:[e-mail]
# DB5021LED
Website

2

3
TABLE OF CONTENTS
Feature Identification ......................................................................................4
Safety Information...........................................................................................5
Operating Instructions.....................................................................................7
Troubleshooting ..............................................................................................12
Care and Maintenance.....................................................................................12
Exploded View and Part List...........................................................................13
Two Years Limited Warranty..........................................................................17
PRODUCTS SPECIFICATIONS
Voltage:120v,60Hz
Input Power:15Amp
Rotation speed:2,100 RPM
Clearing width and depth: Approx. 53 cm x 31 cm (21 in. x 12.5 in.)
Max. throwing distance: 10 m (30 ft.)
Net Wight:18 kg (40lbs)
EN

4
FEATURE IDENTIFICATION
1
Auger Control
7
Auger
2
Switch button
8
Chute Deflector
3
Upper Tube
9
Chute
4
Polarized Plug
10
Chute Crank
5
Lower Tube
11
Knob
6
Wheel
12
Light

5
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
Work Area
Keep work area clean and well-lit. Cluttered, dark areas invite accidents.
Do not operate snow thrower in an explosive atmosphere, such as in the presence of flammable liquids, gases,
or dust. Electrical appliances create sparks that may ignite the dust or fumes.
Keep children, pets, and bystanders away from work area. Be aware that the normal noise of the machine when
turned on may make it difficult for you to hear approaching people.
Electrical Safety
Electrical plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor plugs with
grounded appliances. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There
is an increased risk of electric shock if your body is earthed or grounded.
Do not abuse the cord. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or yank the cord
to disconnect it from the electrical outlet.
Replace or properly repair damaged cords. If cord is damaged in any manner while plugged in, pull the
extension cord from the wall receptacle.
Contact with water while operating the snow thrower can result in electric shock and serious bodily injury. Do
not use the snow thrower in damp or wet locations or expose to rain. Do not handle the plug or the appliance
with wet hands or while standing in water.
Extension Cord-WARNING –Only use a UL-rated extension cord for OUTDOOR, all-weather use (usually
orange color).The extension cord MUST be of the proper gauge size depending on it’s length(see page 11).To
prevent the extension cord from disconnecting during operation.tie it around top right side of the middle frame
before connecting it to the snow thrower as shown in Figure 2 on page 12.
Turn off the power switch and disconnect the power cable before inspecting, servicing, repairing, or cleaning
the snow thrower stop completely.
Do not move or transport the snow thrower when the plug is connected to the power socket and the switch in
turned on.
Personal Safety
Stay alert-watch what you are doing and use common sense when operating the snow thrower.
Do not use the machine when tired, ill, or under the influence of drugs, alcohol, or medication. A moment of
inattention may result in serious personal injury.
Wear proper clothing-Wearing rubber boots offers additional protection from electric shock. Do not wear loose
clothing or jewelry that may become caught in the machine. Wear protective headgear to keep hair away from
revolving parts of the machine. Safety glasses offer better protection than everyday eyeglasses.
Moving parts present risks –Keep your face, hair, clothing, hands, and feet away from moving parts. All guards
and safety attachments must be installed properly before using the unit. Shut off and disconnect cord before
touching any parts other than handles and switch.
Surfaces-This snow thrower is intended for use on paved surfaces. Do not use on gravel, stone, or other
unpaved surfaces unless the snow thrower is adjusted for such surfaces according to the instructions given in
the operators manual.
Avoid accidental starting –Make sure the switch is in the off position before plugging in the unit. Do not carry
the snow thrower with your finger on the switch.

6
Body position-Maintain proper footing and balance at all times. Place heels firmly on the ground and tightly
grasp the handle bar. Watch for uneven surfaces and do not over reach. In case you fall or collide with the snow
thrower, inspect the unit for damage. When steeping backwards, be careful to avoid obstacles beneath your feet
or behind you to avoid falling.
Snow Thrower Use and Care
Know your snow blower-Familiarize yourself with the main parts of your snow thrower. Read the operators
manual carefully. Learn your snow throwers applications and limitations as well as specific potential hazards
related to this machine. Do not use this machine for any purpose other than one for which it was designed.
Otherwise, it may cause mechanical defaults, serious damage or personal injury.
Preliminary unit inspection –Thoroughly inspect the unit before use. Make sure all the parts are secure and
installed correctly. If you notice any abnormalities, do not use the machine until it has been properly repaired.
Always perform a test run the first time you use the snow thrower or after replacing parts to ensure that unit is
functioning properly.
Preliminary area inspection-Clear the area to be plowed before each use. Remove all objects such as rocks,
broken glass, nails, wire, or string which can be thrown by or become entangled in the snow thrower .Keep the
area of operation clear of other people and pets.
Excessive force –The snow thrower was designed to respond at a certain rate for various snow conditions for
optimum safety band performance. Do not force it; keep pressure constant.
Malfunctioning switch-Do not use the snow blower if the switch does not turn it on and off. Any electrical
appliance that can not be controlled by the switch is not safe to use and must be repaired.
Hitting an object-If the snow thrower accidentally strikes an object, stop the snow thrower. Inspect for damage;
repair or replace any damaged part before restarting and operating the snow thrower.
Discharge chute safety -Never direct the snow discharge chute at the operator, at bystanders, at vehicles or at
windows. Thrown snow and foreign objects accidentally picked up by the snow thrower can cause serious
damage and personal injury. Do not use your hands to unclog the discharge chute. Stop the motor before
removing debris.
Abnormal operation-If you notice the snow thrower running in an unstable state or hear abnormal sounds from
machine，stop the machine, disconnect the power immediately, and contact your original distributor.
Noise control-When using the snow thrower, you must respect local laws and regulations regarding noise
control and environmental protection. To avoid noise disturbance, you should carefully decide upon an
appropriate operation time and consider the surrounding conditions.
When work is completed -Disconnected the snow thrower from the power source when not in use, when
changing accessories, and before performing any maintenance.
Store safety-Store snow thrower indoors in a dry area between uses. Keep in a locked area where children and
unauthorized users can not gain access. Do not store the machine while it is still connected to the power source.
It may cause damage and injury.
Maintain for safety and longevity-Check for misalignment or binding of moving parts, breakage of parts, and
any other conditions that may affect the units operation. If damaged, repair or replace the damaged part before
use. Use only those replacement parts made for your model. When replacing any parts, you must strictly
observe the instructions and procedures described in this manual. Special care should be paid to any rubber
parts, since these parts may increase the engine load and decrease its mechanical power if damaged.

7
PRODUCT LABELS
WARNING-Read, understand and follow all safety labels and markings on the unit.
CAUTION
Inspect wiring, which, if damaged during shipping, may cause serious bodily injury during equipment use. If any
damage is seen or suspected, do not assemble. instead, contact our customer service department at 1-800-791-9458.
Handle with care during assembly so that electrical wiring does not become damaged.
OPERATING INSTRUCTIONS
Note: Before using this machine, make sure that the power source you will use complies with the
specification’sdetailedinthismanual.Beforeinsertingtheplugintothesocket, verify that the snow throwers auger and
scraper are firmly attached with screws. Perform a test run to ensure that the rotor turns freely.
SECURING THE EXTENSION CORD
1. For safe and efficient use of your snow thrower, use only a UL-rated extension cord recommended for outdoor
use. Refer to the Extension Cord Chart below.
WARNING
Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:
•Do not allow any part of snow thrower to make contact with water while powered on. If the appliance becomes
wet while turned off, wipe dry before starting.

8
•Use only a UL-rated extension cord for outdoor, all-weather use. Do not use an extension cord more
than150feet long.
•Don't touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots offers
some protection.
EXTENTION CORD CHART
Cord Length
Up to 100 ft.
100-150ft.
Wire Gauge
14
12
2. To prevent the extension cord from disconnecting during use, tie the female end of
the extension cord in to a loose knot on the top right side of the middle frame (B)
before connecting to the male plug in the socket of the snow thrower.
Note: The protective cover around the polarized plug is compatible with most extension
cords. When choosing an extension cord be sure the female end of your cord will fit
into the polarized plug.
3. Note that the snow thrower has a polarized male plug (O), with one prong in the
socket slightly longer and wider than the other. The extension cord female end
should be likewise polarized, so that the extension cord fits snugly into the socket.
WARNING
Damaged electrical cords present risk of fire, electric shock, and serious bodily injury.
Before operating the snow thrower, carefully examine the electrical cord. Id the cord is damaged, do not use the
snow thrower. Replace or repair the damaged cord immediately. If you need assistance, contact our customer
service department at 1-800-791-9458.
POWERING ON AND OFF
1. Connect extension cord to the male plug on the snow thrower then connect
extension cord to proper AC power source.
2. Press and Hold the switch button.

9
3. To start, while holding the switch button in, pull the handlebar toward you until it
touches the handle. The switch button must be pressed in and held before pulling the
handle. Once the snow thrower starts, release the switch button.
4. To stop, release switch button.
USING LIGHT
1. Press button 1 to control the light. Press 1 time for high light, 2 times for low light,
and 3 times for flash. Press 4 times to turn off the light.
2. 2 is the charging port, The light switch displays red when charging and green
when fully charged.
MOVING THE MACHINE AND PLOWING THE SNOW
WARNING
Foreign objects, such as rocks, broken glass, nails, wire, or string, can be picked up and thrown by the snow
thrower, causing serious personal injury.
Remove all foreign objects from the area to be plowed before operating the snow thrower.
Keep the area of operation free of foreign objects that can be become thrown by the rotor blades.
Perform a thorough inspection of the area since some objects may be hidden from view by surrounding
snow, If the snow thrower hits an obstruction or picks up a foreign object during use, stop the snow
thrower, disconnect the extension cord, remove the obstruction, and inspect the unit for damage.
Repair or replace any damaged parts before restarting and operating the unit.
Keep children, pets, and bystanders away from the area of operation. Be aware that the normal noise of the
machine when turned on may make it difficult for you to hear approaching people.
When moving the snow thrower, use the wheels on the sides as the pivot point. Slightly tilt the snow
thrower on this pivot point to move it forward or backward.
Start your clearing path near the electrical outlet and work outward, throwing snow in a back and forth
motion, To clear in the opposite direction, stop over the cord and pivot the snow thrower on its wheels.
Make sure to overlap clearing paths.
Note wind direction. If possible, move in the same direction as the wind so that the snow is not thrown
against the wind (and thus back into your face and back onto the patch).
While moving the snow thrower, do not drag the power cable violently or roughly. The snow thrower
should move within the range that the cable can reach.
Do not push the snow thrower with excessive force. You should push machine gently and evenly in
accordance with the units throw rate.
Some parts of the snow thrower may freeze under extreme temperature conditions. Do not attempt to
operate the snow thrower with frozen parts. If the parts freeze while the snow thrower is in use, stop the
snow thrower, unplug the extension cord, and inspect for frozen parts. Free all parts before operating the
snow thrower. Never force controls that have frozen.

10
Working on pebbles, gravel, or unpaved surfaces-To avoid throwing loose surface material along with the
snow, push down on the raise the scrapper at the base of the unit above the pebbles or gravel.
CHANGING THROW DIRECTION AND THROW HEIGHT
WARNING
Never direct the snow discharge chute at the operator, at bystanders, at vehicles or at nearby windows.
Discharge snow and foreign objects accidentally picked up by the snow thrower can cause serious damage and
personal injury.
Always orient the discharge chute in the opposite direction from where you, bystanders, surrounding vehicles,
or windows are located.
1. The discharge chute (H) can be adjusted 180 degrees
by rotating the chute crank. Rotate the chute control
crank clockwise to move the discharge chute (H) to
the left, counterclockwise to move the chute to the
right.
2. The chute deflector on the top of the discharge chute (H) controls the height of the snow stream. Loosen
both chute deflector knobs to raise or lower the deflector to the desired height you wish to throw the snow.
Tighten the knobs to secure the deflector.
Note: Do not over tighten the chute deflector knobs.
H

11
DRIVE BELT REPLACEMENT
WARNING Entanglement Hazard - Before performing any service procedures, make sure the snow thrower is
disconnected from the power source.
Note: Record component position before disassembly, to assist in reassembly.
1. Using screw driver, remove 3 screws attaching belt cover to housing.
2. Manually push the belt tension pulley up to reduce belt tension.
Note: When replacing the belt it is important to determine the cause of the failure (if applicable) and take
corrective action to avoid repeated failure.
3. Inspect the old belt, pulleys and tension spring before installing a new belt for damage and wear, replace
parts as required
4. Inspect the new belt to ensure it is the correct size and type.
Original –Part Number: 3PK695
5. Manuallypushthebelttensionpulleyuptoallowinstallationofthenewbelt.
6. Position the belt onto the small drive pulley, then while holding the belt tension pulley away from the belt,
carefully wind the belt onto the large pulley. Do not damage the new belt during installation.
7. Using screwdriver, install 3 screws attaching belt cover to housing.

12
TROUBLESHOOTING
Problem
Possible Causes
Remedy
WARNING - Before attempting to make any inspections, repairs or adjustments, stop the snow thrower, wait for
all moving parts to stop moving and carefully disconnect the AC extension cord from the power source.
No start
condition,
won't not
turn on
No power from AC
power source
Connect to known good AC power source
Extension cord not
connected
Securely connect extension cord at power source and
snow thrower
Extension cord faulty
Connect a known good extension cord
Improper starting
procedure
Review "Powering ON and OFF" procedure in this
manual
Auger damaged or
blocked
Check auger for damage, blockage or frozen
condition, repair as required
Faulty switch, wiring or
motor
Call customer service or contact service center
Turns on,
but won't
blow snow
Auger damaged or
blocked
Check auger for damage, blockage or frozen
condition, repair as required
Chute blocked or
damaged
Check chute for damage or blockage, repair as
required
Drive belt damaged
or loose
Check drive belt condition, repair as required (drive
belt is located on left side behind cover)
Turns on,
but won't
run at full
speed
Extension cord faulty
Connect a known good extension cord
Improper extension
cord
Check extension cord length and gauge for use in proper
application, Review "Extension Cord Chart" in this manual
Auger damaged or
blocked
Check auger for damage, blockage or frozen
condition, repair as required
Drive belt damaged or
loose
Check drive belt condition, repair as required (drive
belt is located on left side behind cover)
Faulty wiring or motor
Call customer service or contact service center
CARE AND MAINTENANCE
WARNING
Make sure to turn off the switch and disconnect the extension cord before performing any maintenance task on
your snow thrower.
Run the snow thrower for a few minutes to melt away any snow on the snow thrower. Turn the snow
thrower's power off.
Disconnect the extension cord from the snow thrower.
Examine the extension cord thoroughly for signs of wear or damage. Replace it if it is worn or damaged.
Examine the snow thrower thoroughly for worn, loose bolts or damaged parts. For repairing or replacing
parts, contact customer service.
Store the extension cord with the snow thrower.
Store the unit in a locked and dry or high and dry place to prevent unauthorized use/damage and keep out
of the reach of children. Store the instruction manual along with unit for future use.

13
EXPLODED VIEW AND PART LIST
AUGER HOUSING ASSEMBLY

14
ITEM
SKU#
DESCRIPTION
QTY
ITEM
SKU#
DESCRIPTION
QTY
1
303020561
hex bolt M6*16
6
43
301080009
overcurrent protector
1
2
303050066
shaft ring Φ17
1
44
306010037
screw crimping cap
1
3
303100034
6203Z ball bearing
2
45
303010203
screw 3*10
4
4
303070797
bearing platen welded
2
46
303070074
brush holder
2
5
303020106
hex bolt M8*20
12
47
301110043
brush cover
2
6
303042013
flat washer
12
48
301110058
electrical carbon
2
7
303030036
lock nut M8
12
49
301110044
brush component
2
8
302110091
short scraper
2
50
303010162
screw ST4×70
2
9
302110092
long scraper
4
51
303041008
spring washer
2
10
303181282
auger shaft welded
1
52
303042038
flat wahser
2
11
303042018
flat washer Φ18*Φ24*2
3
53
203020050
rear motor support
1
12
203010646
belt pulley
1
54
303100023
608Z ball bearing
1
13
303042009
flat wahser
1
55
301030008
stator
1
14
303041009
spring washer φ6
1
56
203050587
motor holder
1
15
303020282
hex bolt
1
57
303010185
screw ST6.3*30
4
16
303010176
screw ST6.3×16
2
58
203020063
front motor bracket
1
17
303010383
screw ST4.8*10
1
59
301030005A
rotor
1
18
203050655
right side cover
1
60
303100030
6001Z ball bearing
1
19
203010747
LOGO plate
1
61
303090005
middle cover
1
20
203050170A
base
1
62
303110021
woodruff key
1
21
303070739
right corner
1
63
203060019
small gear
1
22
303010284
screw ST4.8×12
4
64
303030047
nut M8-
1
23
303010108
screw ST4.8*16
3
65
303130019
tensioner spring
1
24
303070741A
Shovel
1
66
303042019
flat wahser
1
25
303070738
left corner
1
67
303020077
bolt M4*10
1
26
302040090
belt 3PK695
1
54
303100023
608Z ball bearing
1
27
203050654
left side cover
1
68
303050029
shaft ring
1
17
303010383
screw ST4.8*10
1
69
303160004
big gear
1
16
303010176
screw ST6.3×16
2
70
303110020
woodruff key
1
28
303030066
normal nut
2
71
303160111
output shaft
1
29
203020336A
knob
2
72
303100024
6201Z ball bearing
1
30
303042023
flat wahser
2
73
303070029
oil pad
1
31
203020380
tooth pad M8*25
2
74
303090002
end cover
1
32
303020161
bolt
4
75
303010221
screw ST4×40
2
33
203050174
upper chute
1
51
303041008
spring washer
3
34
203050175
middle chute
1
52
303042038
flat wahser
3
35
303030077
lock nut M8
2
76
303020079
bolt M4*14
3
36
203010648
chute handle
1
77
303180588
tensioning wheel bracket
welding
1
37
203050172
rotating disc
1
66
303042019
flat wahser
3
38
203010647
located block
1
67
303020077
bolt M4*10
3
39
303130138
chute pressure spring
2
78
203020077
tension wheel
1
40
203050171
base part
1
79
303100016
6000RS ball bearing
1
41
203050567
motor bracket
1
80
303042035
flat washer
1
42
303010358
screw ST4.2×14
2
67
303020077
bolt M4*10
1
16
303010176
screw ST6.3×16
8
81
303160957
small pulley
1
23
303010108
screw ST4.8*16
6

15
PANEL ASSEMBLY

16
ITEM
SKU#
DESCRIPTION
QTY
ITEM
SKU#
DESCRIPTION
QTY
82
303071480
right support
plate
1
29
203020336A
knob
4
83
303010353
screw ST6.3x16
8
28
303030066
normal nut
4
84
303071479
left support
plate
1
105
303081213
middle handle
1
85
303160845
butterfly pin
2
106
303081212
upper handle
1
86
303181283A
shaft
1
107
301120014
light
1
87
203021421
right wheel
cover
1
108
301040045
power cord
1
88
303121002
cotter pin
2
109
303010028
screw 4*18
10
89
303100065
wheel bearing
4
110
302070001
sealing ring
4
90
203050544
8 inch wheel
2
111
203050660
lower switch box
1
91
203050658
left wheel cover
1
112
303130013
knob spring
1
92
203050662
battery pack
cover
1
113
303042019
flat wahser
1
93
303100086
cover shaft
2
114
303010313
screw 4×12
1
16
303010176
screw ST6.3×16
2
115
203021102A
switch button
1
94
203050656
upper cover
1
116
203010655
push rod
1
95
303042019
flat wahser
1
117
203021101A
right switch trigger
2
96
303010363
screw ST4.2*10
1
118
203050552
upper switch box
1
97
203020047
cable clamp
1
114
303010313
screw 4×12
2
16
303010176
screw ST6.3×16
4
119
303130125
anti-self-locking button spring
1
98
203050657
bottom cover
1
120
203010656
anti-self-lock button
1
99
303020124
hex bolt
7
121
303130124
spring
1
100
303042013
flat wahser
6
122
301040078A
connection line
1
101
303030077
lock nut M8
7
123
203050519
wire clip
2
102
303081214
lower handle
1
97
203020047
cable clamp
2
103
303020057
T-screw M8×45
4
124
301100046
switch
1
104
303043010
concave pad
4

17
TWO (2) YEARS LIMITED WARRANTY
POWERSMART IS COMMITTED TO BUILDING TOOLS THAT ARE DEPENDABLE FOR YEARS. OUR
WARRANTIES ARE CONSISTENT WITH OUR COMMITMENT AND DEDICATION TO QUALITY.
TWO (2) YEARS LIMITED WARRANTY OF POWER SMART PRODUCTS FOR HOME USE.
POWERSMART (“SELLER") WARRANTS TO THE ORIGINAL PURCHASER ONLY, THAT ALL POWERSMART
CONSUMER POWER TOOLS WILL BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP FOR A
PERIOD OF TWO (2) YEARS FROM DATE OF PURCHASE. NINETY (90) DAYS FOR ALL POWERSMART
PRODUCTS, IF THE TOOL IS USED FOR PROFESSIONAL OR COMMERCIAL USE.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY UNDER THIS TWO (2) YEARS LIMITED
WARRANTY AND, TO THE EXTENT PERMITTED BY LAW, ANY WARRANTY OR CONDITION IMPLIED BY LAW,
SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN
MATERIAL OR WORKMANSHIP AND WHICH HAVE NOT BEEN MISUSED, CARELESSLY HANDLED, OR
MISREPAIRED BY PERSONS OTHER THAN SELLER OR AUTHORIZED SERVICE CENTER. TO MAKE A
CLAIM UNDER THIS LIMITED WARRANTY, YOU MUST RETURN THE ENTIRE POWER TOOL PRODUCT;
TRANSPORTATION PREPAID, TO POWERSMART INCLUDE A LEGIBLE COPY OF THE ORIGINAL RECEIPT,
WHICH LISTS THE DATE OF PURCHASE (MONTH AND YEAR) AND THE NAME OF THE COMPANY
PURCHASED FROM.
THIS LIMITED WARRANTY DOES NOT APPLY TO ANY ACCESSORY ITEMS INCLUDED WITH THE TOOL
SUCH AS CIRCULAR SAW BLADES OTHER RELATED ITEMS OR TO ANY REPLACEMENT PARTS LISTED
UNDER MAINTENANCE.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO TWO (2) YEARS FROM DATE OF
PURCHASE. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE
OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND
FROM COUNTRY TO COUNTRY.
FOR QUESTIONS / COMMENTS, TECHNICAL ASSISTANCE OR REPAIR PARTS –PLEASE CALL TOLL FREE
AT: 1-800-791-9458 (M-F 9AM –5PM EST) EMAIL: [email protected]
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.

18
TABLE DE MATIÈRES
IDENTIFICATION DES CARACTÉRISTIQUES.......................................................................................................................19
INFORMATIONS SUR LA SÉCURITÉ ...................................................................................................................................20
INSTRUCTIONS D'UTILISATION ..........................................................................................................................................22
DÉPANNAGE .............................................................................................................................................................................27
ENTRETIEN ET MAINTENANCE ..........................................................................................................................................27
VUE EXPLOSÉE ET LISTE DES PIÈCES..................................................................................................................................28
GARANTIE LIMITÉE DE DEUX (2) ANS.................................................................................................................................32
SPÉCIFICATIONS DES PRODUITS
Tension :120v,60Hz
Puissance d'entrée :15Amp
Vitesse de rotation :2,100 RPM
Largeur et profondeur du défrichement : Environ 53 cm x 31 cm (21 pouces x 12.5 pouces)
Distance de projection max. : 10 m (30 pieds)
Poids net :18 kg (40 livres)
FR

19
IDENTIFICATION DES CARACTÉRISTIQUES
1
Contrôle de la tarière
7
Tarière
2
Bouton de commutation
8
Déflecteur de goulotte
3
Tube supérieur
9
Goulotte
4
Fiche polarisée
10
Manivelle de la goulotte
5
Tube inférieur
11
Bouton
6
Roue
12
Lumière

20
INFORMATIONS SUR LA SÉCURITÉ
Veuillez lire et comprendre l'ensemble de ce manuel avant d'essayer d'assembler, d'utiliser ou d'installer le
produit.
Espace de travail
Gardez la zone de travail propre et bien éclairée. Les zones encombrées et sombres sont propices aux accidents.
Ne faites pas fonctionner la souffleuse àneige dans une atmosphère explosive, par exemple en présence de
liquides, de gaz ou de poussières inflammables. Les appareils électriques créent des étincelles qui peuvent
enflammer la poussière ou les fumées.
Tenez les enfants, les animaux domestiques et les passants àl'écart de la zone de travail. Sachez que le bruit
normal de l'appareil lorsqu'il est allumépeut vous rendre difficile d'entendre les personnes qui s'approchent.
Sécuritéélectrique
Les fiches électriques doivent correspondre àla prise de courant. Ne modifiez jamais la fiche de quelque
manière que ce soit. N'utilisez pas de fiches adaptatrices avec des appareils mis àla terre. Les fiches non
modifiées et les prises assorties réduisent le risque de choc électrique.
Évitez tout contact du corps avec des surfaces mises àla terre ou àla masse, telles que les tuyaux, les radiateurs,
les cuisinières et les réfrigérateurs. Le risque de décharge électrique est plus élevési votre corps est mis àla
terre ou àla masse.
N'abusez pas du cordon d'alimentation. Tenez le cordon àl'écart de la chaleur, de l'huile, des arêtes vives ou
des pièces mobiles. Si le cordon est endommagéou si vous tirez dessus, débranchez-le de la prise électrique.
Remplacez ou réparez correctement les cordons endommagés. Si le cordon est endommagéde quelque manière
que ce soit lorsqu'il est branché, tirez la rallonge de la prise murale.
Le contact avec l'eau pendant le fonctionnement de la souffleuse peut entraîner une décharge électrique et des
blessures corporelles graves. N'utilisez pas la souffleuse dans des endroits humides ou mouillés et ne l'exposez
pas àla pluie. Ne manipulez pas la prise ou l'appareil avec des mains mouillées ou en restant debout dans l'eau.
Rallonge électrique AVERTISSEMENT - Utilisez uniquement une rallonge électrique homologuée UL pour
une utilisation en EXTERIEUR, par tous les temps (généralement de couleur orange). La rallonge électrique
DOIT être de la bonne taille en fonction de sa longueur (voir page 31). Pour éviter que la rallonge électrique ne
se débranche pendant le fonctionnement, attachez-la autour du côtésupérieur droit du châssis central avant de
la brancher àla souffleuse, comme indiquédans la figure 2 de la page 32.
Eteignez l'interrupteur et débranchez le câble d'alimentation avant d'inspecter, d'entretenir, de réparer ou de
nettoyer complètement l'arrêt de la souffleuse àneige.
Ne déplacez pas ou ne transportez pas la souffleuse àneige lorsque la fiche est branchée sur la prise de courant
et que l'interrupteur est en position marche.
Sécuritépersonnelle
Restez vigilant, surveillez ce que vous faites et faites preuve de bon sens lorsque vous utilisez la souffleuse.
N'utilisez pas la machine lorsque vous êtes fatigué, malade ou sous l'influence de drogues, d'alcool ou de
médicaments. Un moment d'inattention peut entraîner des blessures graves.
Portez des vêtements appropriés - Le port de bottes en caoutchouc offre une protection supplémentaire contre
les décharges électriques. Ne portez pas de vêtements amples ou de bijoux qui pourraient se prendre dans
l'appareil. Portez un casque de protection pour éloigner les cheveux des pièces tournantes de la machine. Les
lunettes de sécuritéoffrent une meilleure protection que les lunettes de tous les jours.
Les pièces mobiles présentent des risques - Gardez votre visage, vos cheveux, vos vêtements, vos mains et vos
pieds loin des pièces mobiles. Tous les dispositifs de protection et les accessoires de sécuritédoivent être
correctement installés avant d'utiliser l'appareil. Éteignez et débranchez le cordon avant de toucher toute pièce
autre que les poignées et l'interrupteur.
Surfaces - Cette souffleuse àneige est destinée àêtre utilisée sur des surfaces pavées. Ne l'utilisez pas sur du
gravier, de la pierre ou d'autres surfaces non pavées, àmoins que la souffleuse ne soit réglée pour ces surfaces
conformément aux instructions données dans le manuel d'utilisation.