Premier Mounts SVL Series User manual

PLASMA DISPLAY MOUNT MODEL
INSTALLATION MANUAL
VISIT US AT WWW.PREMIERMOUNTS.COM
3130 E. Miraloma Ave. Anaheim, CA 92806 Phone: [phone] Fax: [phone]

2
o Safety & precautions
o Diagrams
o Parts List
o Measure and drill
o Securing the stand
o Securing the mounting bracket
o Securing the plasma to the stand
The swivel stand is a sleek, unobtrusive mounting pedestal that bolts to the top of any flat mounting surface. It offers over 12° tilt and can
swivel up to 45° left and right, depending upon screen size. Access holes on the back plate allow for discreet cable routing through the
neck. Security knobs prevent the plasma from being removed from the stand.
The tabletop surface must be capable of supporting at least five (5) times the weight of plasma display. If not, the tabletop structure must
be reinforced. Proper installation procedure by qualified personnel as outlined in the installations instructions must be adhered to. Failure to
do so could result in serious personal injury
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before
be
g
innin
g
installation. The installation instructions should be read, understood and followed to prevent personal in
j
ur
y
or propert
y
dama
g
e.
Keep these installation instructions in an easily accessible location for future reference.
Indicates that the power plug is to be disconnected from
the power outlet.
Safety precautions must be taken at all times.
Contact Premier Mounts for an
y
q
uestions
Warning and caution in general
Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so may
result in damage to the plasma television and could cause a risk of fire.
At least two qualified people should always perform the installation work. Injury and damage can result from dropping or mishandling
the plasma television.
Contents
Introduction
Safety & Precautions
WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and tools for the
installations procedure to prevent personal injury or damage to the plasma displays or plasma mounts.

3
22.780
7.350
0.448
9.250
10.974
1.187
13.907
13.907
11.432
12.000
12.562
5.750
5.750
SPECS
PART#:
SVL Table-top stand
COLOR:
Silver
A. Bottom plate
B. Covers
C. Front plate
D. Center channel
E. (1) Cable access hole
F. (3) 5/16" Fixed tabletop mounting
points
G. 5/16" Mounting hardware
Stand diagrams
B
C
D
A
E
B
F
E
G

4
5.75 5.75
DESIRED POSITION
DESIRED POSITION
DESIRED POSITION
5.75 5.75
Phillips screwdriver (4) M8 x 20 Phillip screws (4) 5/16"- 18 x 1" Hex head slotted
½" (4) M8 Flat washers (4) 5/16" - 18 x 1¼" Hex head slotted
(4) 5/16" Flat washers (4) 5/16" – 18 x 1½" Hex head slotted
Parts List
TOOLS & SUPPLY NEEDED
Measure and drill
Step 1
Warning: Make sure the tabletop where the stand will be located is capable of supporting at least five times the weight of the plasma display. If it cannot the
tabletop must be reinforced. Make proper measurements and markings on the tabletop where the plasma will be secured. Drill four (4) 3/8" holes through the tabletop stand
to accept 5/16" in diameter screws. Cut the cable access hole to proper size to accept cables. See Fig 1.
HARDWARE
Step 2
Position the SVL tabletop stand front plate facing out and secure with the 5/16" Hex head screws and flat washers (supplied). Do not over tighten the screws. See fig 2.
NOTE: They are 3 different sizes of 5/16" Hex head screws 5/16"-18 x 1" / 1¼" / 1½" please choose the right size according to you installation needs. If you need screws
longer than those provided please use (commercially available) suitable hardware depending on the installation environment. See Fig 2.
Front plate
SVL Stand
Base plate
Table-top surface
Drill
mounting
p
oints
5/16" Hex head screws
5/16" Flat washers
Front plate
SVL Stand
Table-top surface
Cut cable access
o
p
enin
g
Mark mounting
p
oints
Mark cable access
o
p
enin
g
s
Securing the stand

5
Step 3
Secure the mounting-bracket the SVL tabletop stand (8 height adjustable mounting points are found on the front plate, choose the one that will best fit your application).
Secure the plate using the four (4) M8 x 20 Phillip head screws and flat washers (supplied). Do not over-tighten the M8 screws. See Fig 3.
CAUTION: Make sure to check all the
hardware for proper tightness and security.
NOTE: Eight different height adjustable
mounting points are found on the mounting
bracket. Choose the best ones to fit your
application.
Securing the mounting plate
Mounting plate
M8 x 20 mm Phillip
screws
Front plate
Tabletop surface
Table-top surface
M8 Flat washer
Mounting plate
8 Height adjustable
mountin
g
p
ositions
M8 Mounting points
SVL Stand
SVL Stand

6
Thank you for choosing PREMIER MOUNTS INC. for your installation needs.
If you have any questions please contact PREMIER MOUNTS INC.
Information is shown on the front of this page.
Securing the plasma to the stand
Step 5
CAUTION: Two people are required for the next step. Failure to do so may result in personal injury or damage to the plasma display.
Refer to the CTM installation instructions at this time to properly secure the mounting brackets to the plasma display.
Safely raise the plasma display (2 people required) and insert the top and bottom of the hooks to the rods found on the mounting plate. Once the plasma if fully resting on the
r
ods
t
il
t
t
h
e
p
l
as
m
a
to
i
t
s
f
u
ll 12°
a
n
d
secu
r
e
t
h
e
t
w
o
(
2
)
M
6
x 12
secu
rin
g
kn
obs
to
secu
r
e
t
h
e
p
l
as
m
a
to
t
h
e
p
l
ate
.
See
Fi
g
5
.
CAUTION: The two (2) M6 x 12
securing knobs must be applied to
secure the plasma to the plate.
Mounting plate
SVL Stand
Plasma display
Mounting brackets
(2) M6 x 12 Securing
knobs
Plasma display
(2) M6 x 12 Securing
knobs
SVL Stand
Mounting plate
Mounting brackets
M8 Tension nut
M5 Fine tension
ad
j
ustment
Step 6
Once the display installation is complete you could move the plasma display from left to right or right to left to optimize the final position. Gently sliding the unit on the steel
rods of the mounting plate. This adjustment distance will vary depending on the display model being installed. To adjust the tilt tension tighten the M5 screw and M8 tension
nut. See Fi
g
6. Recheck all hardware for
p
ro
p
er ti
g
htness and securit
y
.
Cable access
Table top